空壁噴管 的英文怎麼說

中文拼音 [kōngbìpēnguǎn]
空壁噴管 英文
hollow nozzle
  • 空 : 空Ⅰ形容詞（不包含什麼; 裏面沒有東西或沒有內容; 不切實際的） empty; hollow; void Ⅱ名詞1 （天空） s...
  • 壁 : 名詞1 （墻） wall （of a house etc ） : 銅墻鐵壁 bastion of iron2 （作用像圍墻的部分） wall of st...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  1. According to the feature that deformation resulted from water absorption and mildew appear mainly on the rabbet surface of ccf, this paper adopts rsst to spray a special waterproof sealant on rabbet surface of ccf, so that the sealant can get into fiberboard to certain extent by means of capillarity and penetration, blockage the holes between fibers and capillary, cut up passage of water and change the properties of soakage and sorption to water in capillarity and fiber. at the same time, solidified sealant can form a compact waterproof pellicle on rabbet surface so as to prevent water and humidity from fiber ' s expansion and mildewing

    針對吸水變形、霉變主要發生在地板企口表面的特徵，採用企口表面全封閉法，在復合強化地板企口表面噴塗特殊的防水封閉劑，使其依靠毛細管作用及滲透作用進入板內一定深度，堵塞木纖維之間的空隙及毛細孔通道，截斷水分傳遞的渠道，並改變毛細孔壁及纖維的表面性質以不利於水的浸潤與吸附，同時其固化后能在企口表面形成一層緻密的憎水薄膜，防止水分、濕氣從企口侵入板內引起木纖維膨脹變形、發霉等現象。
  2. This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation

    本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。
  3. Abstract : this paper briefly presents th e application of advanced brazing techniques for a larye number of assemblies of space vehicles, such as thrust chamber and turbine rotor of launch rock et engine, titanium tube of satellite, attitude control engine injector and wave guide component of satell ite, reflector, tube and honeycomb panel of manned spacecraft, main engine nozzl e and preburner of space shuttle as well as the pipeline systems of space statio n

    文摘:簡略地介紹了先進釬焊技術在航天器部件，例如運載火箭發動機的推力室和渦輪轉子、人造衛星的鈦導管、姿控發動機噴注器和波導器件、載人飛船的反射器、導管和蜂窩壁板、航天飛機的主發動機噴管和預燃室以及空間站的管路系統等的廣泛應用情況。
分享友人
分享到 Line

分享到臉書