空間凸輪 的英文怎麼說

中文拼音 [kōngjiāntūlún]
空間凸輪 英文
spatial cam
  • 空 : 空Ⅰ形容詞（不包含什麼; 裏面沒有東西或沒有內容; 不切實際的） empty; hollow; void Ⅱ名詞1 （天空） s...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 凸 : Ⅰ動詞（高出） bulge; protrude Ⅱ形容詞（高於周圍） protruding; raised
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 空間 : space; enclosure; room; blank; interspace
  1. The profile inspection of sc is studied detailedly

    詳細研究了空間凸輪廓面檢測技術。
  2. Processing principle of spatial cam ( sc ) is analyzed intensively

    對空間凸輪的加工工藝進行了深入地分析和研究。
  3. Based on the one - side processing technology, the dissertation proposes a new method of structure design and realizes the drive of sc by pure roller pairs of point engagement. this new drive mode apparently improves the driving accuracy, efficiency, life - span, movement and dynamic feature of scm

    在凸輪廓面採用單側面加工工藝基礎上，提出了結構設計的改進形式，結合廓面修形方法，實現了空間凸輪機構點接觸的純滾動副傳動，顯然提高了機構的傳動精度、效率、使用壽命、運動性能和動力性能。
  4. The instantaneous meshing efficiency of scm is studied

    研究了空間凸輪機構傳動瞬時嚙合效率。
  5. Basic principles of non - equivalent machining of spatial cam surfaces

    空間凸輪廓面非等價加工的基本原理
  6. Analyze the scm ' s structure and its meshing characteristics systematically

    系統分析了空間凸輪機構結構及嚙合特性。
  7. The experiment has proved that those methods can realize precision measurement for spatial cams and reverse design of spatial cam follower motion specifications rapidly and accurately

    實驗結果表明，該方法能快速、準確地實現空間凸輪的精密測量及從動件運動規律反求。
  8. The cam contour curves are reconstructed by nurbs, and a rapid reverse design method for spatial cam follower motion specification via motion simulation is also studied

    利用nurbs實現了凸輪輪廓曲線的重構，並給出基於運動模擬實現迅速反求空間凸輪機構從動件運動規律的方法。
  9. According to the characteristics of spatial - cycloid - ball gearing, meshing transmission theory is studied and related numerical simulation is carried out. major contents are as follows : 1

    本文根據新型空間凸輪活齒精密傳動的特點，研究了嚙合傳動理論，並進行了相應的數值計算。
  10. This project originates from the national high - technology development and research named " the research and application on new spatial - cycloid - ball gearing ", ( no. 2001aa423190 )

    課題來源於國家高技術發展研究計劃項目「新型空間凸輪活齒精密傳動及其應用研究」 （課題編號： 2001aa423190 ） 。
  11. Precision measurement method for spatial cams and probe - radius compensation method are presented in this paper according to spatial cam characteristics, and a specified measure program that can realize real - time probe - radius compensation is programmed

    摘要根據空間凸輪的特點，給出了空間凸輪精密測量及剛球半徑補償方法，並編制了可實現實時測球半徑補償的空間凸輪專用測量程序。
  12. The dissertation puts forward the base circle ' s pressure angle method to calculate the instantaneous meshing efficiency of scm, analyzes the factors affecting instantaneous meshing efficiency and further improves the design theory of scm

    在對空間凸輪機構進行受力分析的基礎上，提出了計算空間凸輪機構瞬時嚙合效率的基圓壓力角法，分析了影響瞬時嚙合效率的因素，進一步完善了空間凸輪機構的設計理論。
  13. Focusing on the spatial cam mechanism ( scm ), the dissertation, starting with the practical processing and the characteristics of the structure and meshing, detailedly analyzes and experiments research the structure theory, processing error and, one - side process and profile inspection of scm with spatial meshing principle and rotating transformation matrix operator methods

    本文以空間凸輪機構為研究對象，從工程實際出發，以空間嚙合原理和旋轉變換矩陣為工具，從結構特點、嚙合特性入手，對空間凸輪機構的結構設計、加工誤差、單側面加工工藝及廓面檢測技術進行了深入地理論分析和實驗研究。
  14. 5 ) under the pro / engineer circumstance, the contact finite element analysis method of the spatial cam sliding tooth transmission are established ; using the i - deas software, the corresponding contact finite element analysis has been done. comparing

    5 ）在pro / engineer環境下建立了空間凸輪活齒傳動的接觸有限元分析模型，運用i - deas軟體進行了相應的接觸有限元分析，並將有限元分析的結果與基於赫茲理論的計算結果進行了對比分析，二者吻合。
  15. The paper analyses affecting on - movement law of special cam that by transition arc radius of special cam, we conclude that transition arc radius should be great than half of groove ' s width and that sharp - angled transition will bring excessive removal while nc - machining

    摘要對空間凸輪的過渡圓弧的半徑大小對凸輪運動規律的影響進行了分析，得出過渡圓弧半徑應大於槽寬的一半，尖角過渡數控加工時會產生過切現象。
  16. 4 ) the three - dimensional solid models of the spatial cam sliding tooth transmission are built up ; the assembling and exploding on the solid modes of those components are made ; the construction of this transmission device is described directly, and the checkout of the assembling coordination between the components of the spatial cam sliding tooth transmission can be done in the design stage

    4 ）建立了空間凸輪活齒傳動裝置的三維實體模型，並對實體模型進行裝配和爆炸處理，直觀地描述了該傳動裝置的結構，實現了在設計階段對空間凸輪活齒傳動零部件裝配協調性的校驗。
  17. Finally, based on the achievement of onc - sidc processing of sc illustrated above, sc has been processed successfully in the five - coordinate machine center and its profile error has been inspected by use of cmm. the result shows that this technology is correct and economic

    最後，基於上述空間凸輪單側面加工理論研究結論，在五坐標加工中心上，成功地加工出了空間凸輪，並應用三坐標鋇l量機對其進行了廓面檢測和誤差計算。
  18. This thesis emphasizes on the mechanics feature of the spatial cam sliding tooth transmission, and the corresponding numerical computing software is developed. all of these offer a feasible method and prompt tool for the intensity design of the new precision transmission

    本文著重對空間凸輪活齒傳動的力學特性進行研究，並開發相應的數值計算軟體，從而為該新型精密傳動的強度設計提供有效的方法和快捷的工具。
  19. Major contents of the thesis are as follows : 1 ) based on brief introduction of the profile theory about the spatial cam sliding tooth transmission, those formulas correlated to the mechanics feature are deduced to calculate the geometrical parameters ; 2 ) according to the hertz contact theory in elastic - mechanics, the mechanics analysis model of the spatial cam sliding tooth transmission is built up ; the deformation harmonizing conditions at each contact point are erected ; the force analysis formulas of point contact are deduced and the resolution method is presented ; 3 ) the numerical calculating software about the deformation of the spatial cam sliding tooth transmission is developed ; using the software, the force characteristics of the spatial cam sliding tooth transmission are calculated with different design parameters ; the general law on force characteristics of this transmission is obtained

    論文的主要內容包括： 1 ）在簡要介紹空間凸輪活動傳動齒廓理論的基礎上，推導了與力學特性相關的幾何參數的計算公式。 2 ）建立了空間凸輪活動傳動的力學分析模型；依據彈性力學赫茲接觸理論，建立了各接觸點之間的變形協調條件，推導了空間凸輪活齒傳動點接觸受力分析公式，並給出了求解的方法。 3 ）開發了關于空間凸輪活動傳動受力變形的數值計算軟體；應用該軟體，對不同設計參數的空間凸輪活齒傳動的受力特性進行了數值計算，獲得了該傳動受力變形的一般規律。
  20. The author proposes a new contact point regress method which can be applied to any type of sc profile inspection by use of coordinate measuring machine ( cmm ), establishes a mathematical model for data processing and error evaluation method, solves the puzzles of the spatial cam profile inspection and error calculation

    提出了以三坐標測量機為工具，適合於任何形式空間凸輪廓面檢測的接觸點回歸法，給出了數據處理的數學模型和誤差計算方法，解決了空間凸輪廓面檢測與誤差計算的難題。
分享友人
分享到 Line

分享到臉書