立齒條 的英文怎麼說
中文拼音 [lìchǐtiáo]
立齒條
英文
vertical tooth rack-
Based on the ostwald - de waele equation, the leakage characteristics of power - law transmitted by helical gear pump are researched, and the leakage model of power - law in the clearence is founded, and - the velocity distributing and the leakage capacity are worked out by the boundary condition. the power loss of leakage is got through the clearence leakage capacity, and the friction power loss is attained by the velocity distributing. the mathematic calculation model
利用冪律流體本構方程，首次對聚合物流體在斜齒齒輪泵中的漏流特性進行了研究，建立冪律流體在間隙中的泄漏模型，利用邊界條件求出速度分佈及泄漏量；由間隙泄漏量得到漏流損失功率，由速度分佈得到流體摩擦功率損失，並得到間隙最優解的數值計算數學模型，同時給出實例及數值計算結果。On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs
考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示Article 59 in the case when any rodent is found to have died of unusual or unknown cause either at the border port or on the conveyance, the border port authorities or the captain of the conveyance is required to the health and quarantine organ about the case without delay so that prompt examination and sanitization can be carried out
第五十九條在國境口岸或者交通工具上發現嚙齒動物有反常死亡或者死因不明的，國境口岸有關單位或者交通工具的負責人，必須立即向衛生檢疫機關報告，迅速查明原因，實施衛生處理。This paper mainly discussed the optimization design of two - stage star - type gear transmission system. it covered the two sides : one - stage gear transmission and two - stage gear transmission. on the basis of their analysis and research, the mathematic models are created which include the objective functions of minimum volume and minimum center distance, the constraints of contact strength, bend strength and scuffing strength
本文主要研究了航空發動機星型齒輪傳動系統的優化設計，對單級齒輪傳動和兩級星型傳動都進行了深入的分析和探討，分別以系統體積最小和中心距最小為目標函數，以齒輪的接觸強度、彎曲強度、膠合強度等為約束條件，建立了完整的數學模型。End mills with brazed helical hardmetal tips - part 4 : technical specifications
硬質合金螺旋齒立銑刀第4部分:技術條件Based on the theories of gear engagement, contact analysis, friction and heat transfer, a three - dimensional finite element model of gear tooth was established to investigate temperature distributions and variations along the contact path over a range of applied loads and operating speeds with consideration of lubrication conditions. sensitivity analysis of surface temperature to gear configuration, frictional heat flux, heat transfer coefficients, and oil and ambient temperature was conducted and the major parameters influencing surface temperature were evaluated
本文基於齒輪嚙合原理、輪齒接觸分析、摩擦學和傳熱學，以有限元分析方法和理論分析計算相結合為手段並以實驗測量結果作為參考，建立了適用於工業應用並具有較高計算精度的高速齒輪傳動輪齒溫度分析的模型和方法，系統地分析了輪齒本體溫度的大小和分佈以及齒輪幾何、載荷及轉速和潤滑冷卻條件等對輪齒本體溫度的影響。Under the conditions of market economy, we must use the market mechanism to protect the environment, cultivate essential environmental market, set up economy inspirit system and mobilize the enthusiasm of principal part of the market. as the legalized economic system, the emission rights trading has been used in developed countries at large, part areas in our country have tried to make experiments. the text points out several basic issues related on emission rights trading, including total amount control, emission license and application of emission rights abroad. combining chinese present problems on applying system of emission rights trading and several cases on emission rights trading in some cites, the thesis explains that it is necessary and promising that emission rights trading is applied in china
本文通過對與排污權交易制度相關的幾個基本問題：總量控制、排污許可證及排污權交易在國外環境領域中的應用的介紹，結合我國目前排污收費制度存在的問題和幾省市進行排污權交易試點的情況，指出排污權交易這一法律化的經濟制度在我國既有應用的必要和前景，也具有相應的運用基礎和條件，並對我國實施排污權交易制度可能遇到的問題及與之相配套的環境立法提出了設想，以期能引起我國學者關于排污權交易制度的大討論，不斷完善排污權交易制度，使其在環境領域中發揮重要作用，成為發展經濟、保護環境這兩個齒輪正常、高速運轉的潤滑劑。Woodworking machines. acceptance conditions and nomenclature for vertical band saws. ripsaws and split saws
木材加工機械.立式帶鋸床的驗收條件和術語.縱割鋸和粗齒鋸Because of the randomness and fuzziness of the design parameters of double circular arc gears, considering randomness and fuzziness of restrict conditions and influence factors in double circular arc gears, adopting fuzzy optimum design method, a optimum mathematical model of the tooth profile parameters of double circular arc gears is established. some examples and their analysis results are also supplied to demonstrate the feasibility and practicability of fuzzy optimum design. compare with the common optimum design method it is an improvement and development
由於雙圓弧齒輪齒形設計參數具有一定的離散性和模糊性，因此本文考慮約束條件的離散性和模糊性以及影響傳動的種種因素的模糊性，採用模糊設計方法，建立了雙圓弧齒輪齒形參數優化的數學模型，並結合實際算例進行分析，結果表明了模糊優化設計的可行性和實用性，是對過去雙圓弧齒輪齒形參數普通優化設計的一種改進和提高。Models of electro - hydraulic servo valve, gear - rack swing hydraulic - pressure oil vat and torque sensor are selected in order to analog the rolling moment more accurately. the transfer function of electro - hydraulic moment servo system is presented and the system parameters are gained. at the same time, the simulation of system is studied
為了能更好的模擬海浪作用於船舶的橫搖力矩，選取了電液伺服閥、齒輪齒條擺動液壓油缸和扭矩傳感器的型號，建立了電液力矩伺服系統的傳遞函數模型，求取了系統參數，並對系統進行了模擬研究。Models of electro - hydraulic servo valve, gear - rack swing hydraulic - pressure oil vat, double shanks hydraulic - pressure oil vat, placement sensor and torque sensor are selected in order to analog the rolling moment and swaying force more accurately. transfer functions of electro - hydraulic moment servo system and placement servo system are presented and the system parameters are gained
為了能更好的模擬海浪作用於船舶的橫搖力矩和橫蕩力，選取了電液伺服閥、齒輪齒條擺動液壓油缸、雙出桿油缸、位移傳感器和扭矩傳感器的型號，建立了電液力矩伺服系統和位置伺服系統的傳遞函數模型，求取了系統參數，並對系統進行了模擬研究。By analyzing the vibration movement of the gear system, the actual center - line equation and that of the theoretic meshing line were derived in their vibration condition, and their movements and the modality of the actual meshing line was analytically verified
摘要根據齒輪系統的振動運動，建立了在振動條件下齒輪副實際中心線方程和理論嚙合線方程，分析論證了實際中心線和理論嚙合線的運動及實際嚙合線的形態。The two key factors, machining methods and machine - setting parameters of sbg, which are related with the generation of theoretical tooth surface and topographic deviation for sbg, are analyzed in details. after building the machine - tool mathematical model and computing the tooth surface parameters, using the given conditions and mesh equation, the coordinates of the theoretical tooth surface of sbg can be computed, and, then, the theoretical tooth surface model of sbg is derived
本文詳細地分析了形成螺旋錐齒輪理論齒面及產生拓撲誤差的兩個關鍵因素，即螺旋錐齒輪的切齒加工方法和機床調整參數;通過建立機床數學模型，計算齒面參數，用已知條件和嚙合方程進行聯合求解，得出了理論齒面的坐標值，從而獲得了螺旋錐齒輪的理論齒面模型。We go all out to provide various reliable upper - and - lower ball joint for independent suspension, or rack end for rack - and pinion steering
我們竭誠提供始終為中外新老客戶值得信賴的各種結構形式的獨立懸架用上下球較節，和齒輪齒條轉向機構的齒條接頭。Then acoustic radiative pressure level is computed with a 3 - d fe acoustic - field model and bounary conditions imported from the result of vibration response by infinite fem
建立齒輪箱外聲場二維有限元模型，導入齒輪箱振動響應結果作為聲學邊界條件，並採用無限有限元法計算了輻射聲壓級。Abstract : according to the interrelation between the reliability and the optimization desi gn in gear drive, an optimal mathematics model of double reduction planetary tra nsmission is set up on rational reliability conditions
文摘:根據齒輪傳動可靠性與優化設計的相關性，建立起雙級行星齒輪傳動在合理可靠性條件下的優化設計數模。Its longish hood and two - tone interior cloak a responsive chassis that incorporates a fully independent suspension and rack - and - pinion steering, tuned to handle everything from rough pavement to highway curves
它修長的折式車篷和兩種色調的內部裝飾下，隱藏著是一個可對駕駛做出靈敏反應的底盤，其中融合了一個完全獨立的懸架和齒條齒輪式轉向裝置，它們可應付起伏不平的路面和高速公路轉彎的各種情況。Major contents of the thesis are as follows : 1 ) based on brief introduction of the profile theory about the spatial cam sliding tooth transmission, those formulas correlated to the mechanics feature are deduced to calculate the geometrical parameters ; 2 ) according to the hertz contact theory in elastic - mechanics, the mechanics analysis model of the spatial cam sliding tooth transmission is built up ; the deformation harmonizing conditions at each contact point are erected ; the force analysis formulas of point contact are deduced and the resolution method is presented ; 3 ) the numerical calculating software about the deformation of the spatial cam sliding tooth transmission is developed ; using the software, the force characteristics of the spatial cam sliding tooth transmission are calculated with different design parameters ; the general law on force characteristics of this transmission is obtained
論文的主要內容包括： 1 ）在簡要介紹空間凸輪活動傳動齒廓理論的基礎上，推導了與力學特性相關的幾何參數的計算公式。 2 ）建立了空間凸輪活動傳動的力學分析模型；依據彈性力學赫茲接觸理論，建立了各接觸點之間的變形協調條件，推導了空間凸輪活齒傳動點接觸受力分析公式，並給出了求解的方法。 3 ）開發了關于空間凸輪活動傳動受力變形的數值計算軟體；應用該軟體，對不同設計參數的空間凸輪活齒傳動的受力特性進行了數值計算，獲得了該傳動受力變形的一般規律。The establishment of diagnosis model about gear fault the history fault data of gear case is analysed by clustering supplied by analysis services of microsoft sql server 2000, and the data which has the same property and fault type is classified as a group. traversing 8 property and outcome of this cluster obtained can get a rule. rules whose degree of support or belief doesn ’ t meet the demand are deleted and the diagnosis model is established from the rest rules
2 .齒輪故障診斷模型的建立利用sqlserver2000中analysisservices提供的聚類法，對齒輪箱歷史故障數據進行挖掘，將具有相似屬性特徵且故障類型一致的數據分成同一組，得到一個聚類，遍歷這個聚類的8個屬性至結論得到一條診斷規則，濾掉支持度和可信度不滿足要求的規則，最後由所有規則建立診斷模型。分享友人