端接焊接頭 的英文怎麼說
中文拼音 [duānjiēhànjiētóu]
端接焊接頭
英文
edge joint weld- 端 : Ⅰ名詞1 (東西的頭) end; extremity 2 (事情的開頭) beginning 3 (門類; 方面) item; point 4 (原...
- 接 : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
- 焊 : 動詞(用熔化的金屬修補金屬器物或使金屬工件連接起來) weld; solder
- 端接 : head joint; terminating; heading joint; termipoint
- 接頭 : 1 (連接起來) connect; join; joint 2 (找人聯系) contact; get in touch with; meet 3 (了解情況...
-
As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers
本機床是電站大型汽輪發電機組的管道施工的關鍵設備,對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口,端平面,內外徑過緩斜度及直口,能滿足施工現場和製造廠家對各種管件的加工要求。Copper and copper alloys - plumbing fittings - fittings with short ends for capillary brazing to copper tubes
銅和銅合金.管路接頭.銅管毛細管銅焊法用短端頭接頭The kind of welding equipment is suitable forwelding the qarts in appplications of heat exchanger in - out water pipe port of electical heater and hot pipe fittings simple operation low lost and good seam foring are the advan tages. it is an essential and special equipment in the profression of tube - making electrical and solar water heaters
該系列焊接設備適用於太陽能熱水器端蓋及水箱內受到影響上的進出水管、熱管接頭、電加熱器接頭及搪瓷水箱進出水管的自動化焊接,焊縫盛開有美觀、效率高、成本上升低,是制桶業、太陽能熱水器、電熱水器等行業必不可少的專用設備。Solderability tests for component leads, terminations, lugs, terminals and wires
元件引線接線端焊片接頭和金屬絲的軟釬焊性試驗Aerospace series - pipe coupling 37, in heat resisting steel - ferrules, welded end - inch series ; german and english version en 4555 : 2003
航空航天系列.耐熱鋼制37 ?球面管子接頭.焊接端套圈Aerospace series - pipe coupling 8 o30 ' in titanium alloy - unions, bulkhead long welded end, for repair
航空航天系列. 8 30 ' .鈦合金聯管節.檢修用長的焊接端部的悶頭管接頭Aerospace series - pipe coupling 8 o30 ' in titanium alloy - unions, welded end threaded for repair
航空航天系列. 8 30 '鈦合金管接頭.檢修用端部焊接的螺紋管接頭Non - soldering and soldering compression fittings - stud ends for use with union nut ; design sheet
非釬焊和釬焊壓合接頭.與管接螺母使用的雙頭螺栓端部Valves - socket welding ends for steel valves ; german version en 12760 : 1999
閥門.鋼閥門的承口焊接端頭Aerospace series - pipe coupling 8 30 ' in titanium alloy - ferrule, welded, with dynamic beam seal end
航空航天系列.鈦合金8 30 '管連接件.帶動力橫梁密封端頭的焊接環箍Aerospace series - pipe coupling 8 30 ' in titanium alloy - ferrules with dynamic beam seal end, welded and reduced at pipe end
航空航天系列.鈦合金管連接件8 30 ' .在管端焊接和變徑的帶動力橫梁密封端頭的環箍Resistance spot welding - electrode adaptors, male taper 1 : 10 - part 2 : parallel shank fixing for end - thrust electrodes iso 5183 - 2 : 2000 ; german version en iso 5183 - 2 : 2002
電阻點焊.外錐度1 : 10電極接頭.第2部分:軸端推力電極Resistance welding equipment - electrode adaptors, male taper 1 : 10 - parallel shank fixing for end - thrust electrodes
電阻焊設備.外錐度1 : 10電極接頭.端推力電極用平行柄接頭Resistance spot welding - electrode adaptors, male taper 1 : 10 - part 2 : parallel shank fixing for end - thrust electrodes
電阻點焊.外錐度1 : 10的電極夾頭座.第2部分:端推力電極用直柄接頭Aerospace series - pipe coupling 8 30 ' in titanium alloy - unions, welded end threaded for repair
航空航天系列.鈦合金管連接件8 30 ' .修理用焊接端頭螺紋活接頭Aerospace series - pipe coupling 8 o30 ' - dynamic beam seal end for ferrule, welded - geometric configuration
航空航天系列. 8 30 '管接頭.金屬包頭焊接用動態梁密封端.幾何構型Abstract : the brazing technology for asynchronous traction motor is introduced from various aspects as the choosing of end - ring and conducting bar materials, solder and flux, brazing joint type and brazing technology
文摘:從端環和導條材料的選擇、釬料和釬劑的選擇、釬焊接頭型式的選擇及其釬焊工藝等方面介紹了異步牽引電動機端環與導條的釬焊技術。Non - soldering compression fittings with cutting ring - double ended stud ends with parallel threads and shaft for stud ends type a
帶切割環的非釬焊壓合接頭.柱螺栓端a型帶平行螺紋和Crimp - type cable sockets for solderless connections, insulated, for copper conductors
銅導線用絕緣非焊接連接的壓接電纜端頭Non - soldering compression fittings with cutting ring - double ended stud ends with parallel thread for stub ends type a
帶切割環的非釬焊壓合接頭.鈍端a型帶平行螺紋的雙鈍分享友人