端板 的英文怎麼說

中文拼音 [duānbǎn]
端板 英文
header; end plate; end sheathing; end sheet
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  1. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  2. These jets are usually either endplate or contraction types.

    這種實驗段通常有端板型的或收縮型的。
  3. Finite - element analysis of end - plate connections in light weight steel structure with gabled frames

    門式剛架輕鋼結構端板連接節點承載性能的有限元分析
  4. Furthermore, in order to predict the force at beam tension flange when end - plate yields, kulak method, applied to determine the ultimate strength of the t - stub connections, are modified by introducing a parameter c. the general solution of parameter c is also provided in this paper

    在有限元計算的基礎上，本文分析了影響節點強度的主要因素，包括： （ 1 ）螺栓和端板的強度； （ 2 ）柱翼緣的抗壓強度； （ 3 ）柱腹板的抗壓強度。
  5. Steel moment - resisting frames with welded beam - to - column connections were traditionally regarded as having excellent performance, and widely adopted in steel constructions, but this opinion changed after the 1994 northrige earthquake and the 1995 hyogoken - nanbu earthquake. these earthquakes also arouse engineers to resurvey the behavior of end - plate connections

    傳統觀點認為，樑柱焊接剛性連接具有較好的抗震性能，因此在工程中得到了廣泛地應用，但1994年的northrige地震和1995年的阪神地震改變了這種傳統觀點，這兩次地震也引起了工程技術人員對端板連接的再審視。
  6. 2. pseudo - static force testing of twelve full - scale connections, including top - seat angle connections, two web flange and top - seat connections, extended - end - plate connections, slit - t steel connections and dog - bone connections are carried out for the first time in our country

    2首次在國內大規模地進行了頂底角鋼連接、帶雙腹板頂底角鋼連接、外伸端板連接以及短t型鋼連接等半剛性連接以及狗骨式剛性連接這五種連接類型共十二個原型試件的擬靜力試驗。
  7. Cyclic tests of semirigid end - plate connections in multi - story steel frames

    多層鋼框架半剛性端板連接的循環荷載試驗研究
  8. Two hypothesises, different from the traditional viewpoints, about stress distribution in beam section at the connection of beam and end - plate are presented by author to determine the ultimate moment of end - plate connection

    其計算過程分為兩步： （ 1 ）計算梁受拉翼緣的極限拉力； （ 2 ）計算端板連接的極限彎矩。
  9. The main popular theoretical method adopted to study end - plate connection is finite element technique under monotonic loading at present. this paper applies nonlinear ( material, geometry and contact ) finite element method to analyze the behaviors of connections under cyclic load at fist time. contact elements are set between end plate and column flange, screw cap and neighborhood plane, bolt bar and hole

    對于端板連接的理論分析，目前國內外的研究主要局限在單向加載有限元分析范疇，本文首次採用三維非線性（包括材料、幾何與狀態非線性）有限元對端板連接進行了循環加載分析，端板與柱翼緣間、螺栓頭（帽）與相鄰板件間、螺栓桿與孔壁間都設置了反映邊界狀態的接觸單元。
  10. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  11. Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior

    分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大，實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著，而連接端板厚度及剪力連接程度的影響則不是太顯著。
  12. On the basis of mode experiment of the drums, the paper analyzes the impacts of the drum end and the gradual wind of the wire ropes on the drum strength. and also on the basis of the analysis of the data of the drum mode experiment, the paper presents the research conclusion that unstability mostly occurs where drums are fully wound with wire ropes

    在進行捲筒模態試驗的基礎上，分析了捲筒端板和鋼絲繩逐步卷繞過程對捲筒剛度的影響關系，在對大量的捲筒模態試驗數據分析歸納的基礎上，給出了鋼絲繩全部繞滿捲筒是最容易發生失穩的研究結論。
  13. The experiment procedure and analysis result about exteriorly extended end - plate connection with high strength bolt are introduced primarily ; each sample ' s dimension is given. the adding load equipment, measuring apparatus placed, measuring point established is detailed. adding load measure load and m - curve is produced ; the single span gabled frames horizontal displacement formula is deduced when the horizontal concentrated force is applied to it

    重點介紹了外伸端板高強螺栓連接的實驗過程及實驗分析結果，介紹了各組試件的形狀尺寸、加載裝置、測量儀器安放、測點的布置等；給出加載方式及測出的m -曲線；計算出試驗節點的初始剛度；推導水平集中力作用下單跨門式剛架考慮節點半剛性的側移計算公式。
  14. But results from studis of r. hansan and n. kishi have shown that only when the initial stiffness of connection is more than 105. 05 kn - m / rad, the joint is considered as rigid connection, otherwise it should be dealt with semi - rigid connction

    但根據r . hansan和n . kishi等人的研究表明，當螺栓端板連接的初始連接剛度大於10 ~ （ 5 . 05 ） kn - m rad時，這種連接才可以看作是剛性連接，否則就應將其視作半剛性連接。
  15. The factors, such as end - plate thickness, bolt ' s types, beam and column " flank, that can effect on the joint rigidity and moment capability, are analyzed

    分析了節點端板厚度、螺栓類型、端板的加勁肋等因素對節點剛度以及抗彎承載力的影響。
  16. Nonlinear finite element analysis of beam - column end - plate joints

    樑柱端板連接節點的非線性有限元分析
  17. To meet this challenge, a research project was supported by ministry of communication and bv shanghai zhenhua port machinery co. ltd. focusing on analysis of tdtcd ( traditional design theories of crane drums ) the paper has studied the impacts of features under the binding force of wire ropes, the end - plate and rope slot. this study is based not only on the thin shell theory and viscoelastic mechanics to calculate the strength and stability of drum, but also on an experiment with technology in " state of act "

    本文結合交通部重點科技項目「港口起重機鋼絲繩傳動件高性能技術研究」和上海振華港機股份有限公司委託項目「起重機焊接捲筒極限壁厚研究」 ，針對起重機捲筒傳統設計方法偏於保守的情況，以薄殼理論和近代力學為基礎，以現代試驗技術為研究手段，對鋼絲繩緊箍力作用下的外載特性、端板、繩槽等因素對捲筒強度和穩定性的影響進行了系統的理論研究，在深入開展捲筒強度、穩定性和實驗模態分析等試驗的基礎上，提出了有別于傳統方法的捲筒強度、穩定性計算方法。
  18. No endplate of reasonable size will prevent tip flow.

    沒有一個合適的端板尺寸將會阻止翼根繞流。
  19. Finite element analysis of end - plated semi - rigid composite joints

    端板型半剛性組合節點的有限元分析
  20. Exploration on the design method of bolted end - plate connection

    對鋼結構端板連接節點設計方法的探析
分享友人
分享到 Line

分享到臉書