等切變線 的英文怎麼說
中文拼音 [děngqiēbiànxiàn]
等切變線
英文
isoshear-
Experimental results show that the bistable of tuned substrate self - bias was determined by discharge gas pressure, discharge power and tuning circuit parameters etc. the bistable exists is because of there is capacitive coupling in icp system and sheath capacitance is nonlinear
實驗結果表明這種跳變回滯現象與等離子體的放電氣壓、射頻功率以及調諧外電路的參數等多種因素密切相聯系。而產生跳變回滯現象的原因是icp中存在容性耦合以及鞘層電容具有非線性特性。Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece
將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義During piano playing and teaching, we should pay attention to rhythm changing of formal or informal rhythm, strong or weak beat, syncope or link line tercet or various slur
在鋼琴教學及演奏中，要注意正規節奏與不正規節奏、強起拍與弱起拍、切分音與連結線、三連音及各種連音符等節奏的變化。The new developments of htm station technique were introduced from the aspects such as changing the htm pipeline type in pet htm station, increasing the switch forms of steam atomization and compressed air atomization, increasing the steam generator, sending stripping tower off - gas to combination and using new material nd steel in air preheater
摘要從改變聚酯熱媒站的熱媒爐熱媒管線形式、增加蒸汽霧化與壓縮空氣霧化的切換形式、增加蒸汽發生器、汽提塔尾氣送燒、空氣預熱器採用新型材質nd鋼等方面介紹熱媒站技術的新發展。The connection between the torque and the polarized charges is established. on the base of mathematical model of torsional effect, using multivariate unrestrained nonlinear optimization method, we research cutting angles and parameters of crosssection to get best torsional sensitivity
在建立石英晶體扭轉效應模型的基礎上，應用多變量、無約束非線性優化方法對于晶體切型、截面形狀等參數進行了優化，以獲得最佳扭轉靈敏度。At present, the most of vtr which are used in watch - control occasion for speciality are short of a uniform control - check - alarm system, which brings on the discommodiousness of operation and the user can not know the time of occurring a fault, which reduces the reliability of the watch - control system. therefor, at first, i carefully analyze the servo theory of the vtr which had been produced by chmavc with k mechanism to find out the work rule of the control signal ; second, take out some right control signal ; then for dealing with the problem of vtr in use for watch - control, i choose some right components to design the uniform control system for many special vtr with protel software. it mainly includes the following functions : operation functions of all vtr ( for example : power, play, ff, rew, stop, rec, eject, fwd, rwd, sp, lp ) was controlled by line at the same time ; in, the process of recording, when the tape walks to the end or stops by itself, the system gives an alarm and shows the number of the wrong vtr ; in the process of recording, the system gives an alarm and shows the number of the wrong vtr when the video signal from vidicon is losed ; the system controls all vtr to record on the non - working time when there is something wrong in the guarding section ; the system controls the video from vtr to switch to right monitor
目前，用在監控場合的業務用錄像機普遍缺乏一個統一的控制及檢測報警系統，這就導致了操作的不方便和出現了故障用戶不知道，降低了監控系統的可靠性，為此，我首先對華錄松下生產的k機芯的錄像機伺服原理進行仔細分析，找出各個伺服控制信號的控制變化規律；然後從中選出合適的控制信號；針對目前錄像機在實際監控使用過程中存在的問題，選用合適的元器件；運用protel繪圖軟體，設計了這個多臺業務用錄像機的統一控制系統，她主要包括以下功能：錄像機操作功能（如power play ff rew stop rec eject及正尋反尋帶速設定等）的統一線控控制功能；磁帶在記錄過程中，磁帶到頭和磁帶自己「偷停」的報警，並要能顯示出具體是哪一臺錄像機；在記錄狀態下，攝像頭輸入信號丟失報警，並要能顯示出具體是哪一臺錄像機；在休息或其他不需要記錄時，一旦警戒區有情況，則控制所有機器自動進入錄像狀態的功能；從錄像機輸出的監控圖像信號對監視器的切換功能。Aiming at such problems in combustion system of homemade middle and miniature boiler, as a complex system with the character of dead zone, time variation, serious non - linearity, large time delay, coupling and a lot of disturbance, this paper presents a new set of optimal control resources. by using well - matched control method on system, stable automatic running is realized. having the serious divulgence coals difference a lot from each other in character, instability of chemistry, value of lowest emission of heat, home - made boiler controller is not at all ideal. instead of traditional model that controls the ratio based on proportional control or with the correct signal of the amount of oxygen, this paper, combined with intellect control theory - - fuzzy control and self - optimizing concept, propounded a kind of fuzzy self - optimizing controller to be used in air supplying system of the boiler, and expatiates on the idea of dividing the control process into two parts, dynamic and static to realize, thus meets the demand of homemade boiler economic running
本設計針對國產中、小型電站鍋爐燃燒系統參數時變、嚴重非線性、干擾因素復雜、耦合嚴重、模型不易確定的特點，提出多變量協調控制方案，解決了系統可控性差，難以實現穩定自動運行的問題；在此基礎上，改變以往以煙氣含氧量控制送風的傳統模式，針對國產電站鍋爐設備主體及一、二次送風迴路泄露嚴重，煤種混雜、成分不穩定、燃燒發熱值低、燃燒效率不高等問題，應用智能控制理論中的模糊控制技術，結合自尋最優控制的思想，設計了一種模糊自尋優控制器，應用在電站鍋爐送風控制系統上，並闡述了動靜態兩種實現途徑，通過在線優化風煤配比，實現最佳經濟燃燒，切實保障了鍋爐的經濟運行。Study achievement appears as following aspects : ( 1 ) yellow river estuary gate river flow and tide flow mixed area is not keep standing deposition status, on special income water and sediment conditions, boundary conditions and oceanic power conditions, this area may on the scour status ; ( 2 ) observed from estuary sediment deposition distributing process : delta and sea offing area sediment deposition vary trend is similar, each part sediment deposition scale varies as wave shape ; ( 3 ) on estuary gate, affect the sediment deposition factors, primary factors are tide prop, the gate widens gradually, estuary gate have branches, brine induced flocculation. this paper study the estuary gate widen, estuary gate have branches to affect the river channel deposition in quantity ; ( 4 ) based on field measured data, for the first time, deduce the estuary sediment deposition and distributing regress formula which can estimate estuary different areas sediment deposition volume ; ( 5 ) this subject demonstrate the estuary delta coastline dynamic balance conception, build the relationship between the estuary income sediment with deposition land area, draw the following important conclusion : when estuary years - averaged income sediment keeps at 345 million tons, the delta coastline may on the dynamic balance status. ( 6 ) this subject firstly brings up estuary sediment optimized control conception, and has the primary study on the macroscopically optimized control conception method
研究認為： （ 1 ）黃河河口口門逕流潮汐區域並非持續保持淤積狀態，在特定的來水來沙、邊界條件和海洋動力條件下，該區域可以處于沖刷狀態； （ 2 ）從河口泥沙沉積分配的過程來看：三角洲與濱海區泥沙的沉積變化趨勢是基本一致的，各部位的泥沙沉積比例變化基本呈波動狀態，且三角洲與濱海區泥沙的沉積比例與來沙量密切相關，基本成正比關系； （ 3 ）在口門處，影響泥沙沉淤的因素主要集中在潮汐頂托、口門逐漸加寬、河口門分汊、鹽水造成絮凝等，本報告主要對口門加寬，口門西妥理工大學工程碩士專業學位論文分漢對河道淤積的影響進行了定量分析: （一扣根據實測資料首次建立了河贖流路泥沙沉積分配的回歸計算式，據此可以預估計算河口不同區域泥沙的沉淤量; 、 5 ）本項研究首次論證了河口三角洲岸線動態平衡的概念，並建立了黃河河口來沙量與造陸面積的相關關系，得出了當河口多年平均來沙量維持在3 . 45億t時其河口三角洲岸線則可能處于動態平衡狀態的重要結論; 『 6 ）本項研究首次提出了河口泥沙優化調控的概念，並對其宏觀優化調控模式進行了初步探討。Solution of nonlinear wave loads in regular oblique seas. based on strip method, thinking about nonlinear factors such as no straight shipboard on waterline, the instantaneous variation of wet surface shape and slamming effect of ship bottom, the numerical methods of nonlinear fluid force in large amplitude oblique regular seas are discussed
關于斜浪規則波中非線性波浪載荷的計算:本文基於切片理論，考慮到船體非直舷、水下剖面形狀的瞬時變化以及砰擊等非線性因素，討論了大波幅斜浪規則波中非線性流體力的時域計算方法。Compared with traditional arithmetic, the result shows that the improved method is better in keeping integrality and consistency of image, image segmentation, threshold edge detection
然後針對骨髓切片圖像中粘連細胞的特點，運用了基於距離變換的分水嶺分割演算法以及等值線跟蹤及臨界跟蹤法完成了對粘連細胞的分割。The main relative systems of heavy - hard rainfall in northeast plateau are western pacific subtropical high, south asia high, low latitude systems, upper level jet ( ulj ), low level greater wind speed axes, westerly trough and plateau trough, low level vortex, cold frontal, occluded front in qinghai lake, mesoscale low pressure, heat low - pressure in qinghai, shear line and convergence line, mesoscale cloud cluster, etc. the west subsidiary model of south asia high is the main circulation type of heavy - hard rainfall in this area
3 、西太平洋副高、南亞高壓、低緯系統、高空急流、低空大風速軸；西風槽和高原槽、低渦、冷鋒、青海湖錮囚鋒以及中尺度低壓、青海熱低壓、切變線與輻合線、中尺度雲團等系統是高原東北部地區大到暴雨的主要相關系統。 100hpa上的南亞高壓中心強度加強，位置東西擺動預示高原地區將有降水產生，中心強度減弱，降水過程結束。南亞高壓西部副型是高原東北部地區大到暴雨的主要流型。Secondly, their aims are made the investment of substations, feeders or running cost of electric power system minimum. but they do n ' t take into account of land utilization, street accessibility of right of way, etc., but demands of electric power system. generally, a straight line distance, namely, euclid distance, was used for calculating the distance between a load point and a substation, which is a straight forward but non - practical way for most planning techniques
其次受研究工具的限制，這些模型以工程投資、運行費用等最小為目標，僅能考慮導線載流量、電壓降等電力系統技術約束條件，簡化略去了用地限制、街道可達性等重要的自然約束條件，且求解這些模型的前奏是計算負荷點到變電所的歐幾里得距離（直線距離） ，簡便但不切合實際（這一點在城市電網規劃中尤其重要） ，因此較難給出技術上可行的最優解。Clear of any power sources such as power lines, transformer stations, pylons, and transmitter towers, etc which might cause radio interference
遠離一切可干擾無線電訊息的電源，例如電線、變壓站、高壓電線和變壓塔等；Based on the continuous damage theory, considering the shear effect, the high - order shearing, flexural and in - plane deformation coupling model is built ; through the nonlinear fem analysis of rc beams strengthened with frp, the damage theory and damage course is researched ; compared with experiment results, it shows that the model is effective ; the fem analysis software is prepared to provide simple and effective method for the engineering application ; using the soft the frp strengthened beams before and after damage is modeled so as to provide the theory base for engineering application
摘要基於連續損傷理論，考慮膠層的剪切效應，建立frp加固鋼筋混凝土梁的高階剪切彎曲及面內變形耦合模型，編制了有限元分析的軟體，進行非線性有限元分析；通過與已有的試驗結果進行對比，證明該模型的簡單，有效性；利用該軟體對未加固混凝土梁，初始進行加固的混凝土梁以及最大拉應變達到極限值時進行加固的混凝土梁等幾種情況進行數值模擬。The dosage of the hormones are difficult to control, and they can bring out side effects, such as hoarse voice, excess growth of body hair, and so on, so this kind of hormone should not be taken without doctor s instruction
但用藥的份量難于掌握及會產生副作用，例如：聲線變粗、毛發增多等，所以切勿擅自服用。Because the different stiffness match of front and rear suspension is very influencing to the ride comfort, optimal model of ride comfort is developed, regarding the rms of driver ’ s acceleration as the objection, regarding the stiffness of front and back suspension as optimal variable, regarding quiet flexibility 、 dynamic flexibility 、 frequency and dynamic load as nonlinear constraints. by matlab program and using sqp, the optimal match of front and back suspension ’ s stiffness is achieved, this optimal model consider not only request of quiet 、 dynamic flexibility 、 frequency and damp, but also security of run and peace of road, it is closer to the fact than other models which only consider partial restriction
由於前後懸架垂直剛度的不同匹配對汽車行駛平順性影響較大，論文建立以駕駛員垂直加速度的均方根值作為汽車行駛平順性優化目標值、以前後懸架垂直剛度作為優化變量的優化設計模型，並輔以靜撓度、動撓度、頻率、動載荷等非線性約束，使用序列二次規劃法，利用matlab編制優化程序，求得前後懸架垂直剛度的最優匹配值;此優化模型不僅包含動靜撓度及頻率和阻尼的限制，還考慮到汽車的行駛安全性和道路友好性，比文獻報道的只考慮部分約束的優化模型更切合實際情況。This variation of stresses is due to the action of in - plane shear strain in the plate, which is termed “ shear - lag ”. stresses larger than the elementary bending uniform stress thus develop at the web - flange connection. an appropriate reduced “ effective width ” of the plate - with the uniform stress equal to the maximum longitudinal stress - has been widely used by engineers in conjunction with the elementary beam bending theory
但實際上翼緣中剪切變形是不均勻的，由此導致正應力沿橋寬呈曲線分佈，從而引出了有效寬度的概念，即按初等梁理論的公式也能得與真實應力峰值接近相等的那個翼緣折算寬度。Aim : to analyze the mechanism, thermadynamic theoretical basis, dynamic mechanism and influencing factors of thermally induced phase separation ( tips ) in order to completely grasp the factors affecting the size, distribution and form of pores, so that the adjusted range of pore can be widened and the preparation of porous membrane can be repeated and controlled. methods : considering from the structural characteristics of tissue engineered materials, the methods of preparing porous membrane using tips technique, the hermadynamic theoretical basis, dynamic mechanism and influencing factors were analyzed, the problems and investigative directions in the future were also analyzed. tips technique is a process of phase separation of polymer homogenous solution under quenching, and it is suitable for diameter and structural form of the micropore materials prepared using tips are closely correlated with the kind and dispensing proportion of polymer attrnuant, polymer concentration and polymer molecular mass, etc. conducted, including determination of polymer - solvent system phase diagram, study of form and appearance of porous membrane of different thickness, study of form and appearance of porous membrane prepared with systems of different x, which is the parameter of polymer - solvent interaction
目的:分析熱致相分離成膜過程的機理、熱力學理論基礎、動力學機制以及影響因素，以便充分掌握影響孔度大小、分佈、形態的因素，使孔度調控范圍得以拓寬，使多孔膜的制備能重復可控.方法:從組織工程材料結構特點出發，分析熱致相分離聚合物多孔膜的制備方法及該法成膜的熱力學理論基礎、動力學機制以及影響因素.並分析實驗中存在的問題及今後的研究方向.結果:以熱致相分離法可制備聚合物多孔膜.熱致相分離法制備多孔膜是高聚物均相溶液在淬冷條件下發生相分離的過程，它適用於上臨界共溶溫度型聚合物一稀釋劑二元體系.熱致相分離法成膜的過程，可以認為是旋節線機理佔主導地位.熱致相分離法制備的微孔材料，其孔隙率、孔徑大小、結構形態與聚合物稀釋劑的種類、組成配比、聚合物濃度、聚合物分子量等因素密切相關.結論:可採用熱致相分離技術制備多孔膜，通過改變不同的成膜條件可獲得一系列不同孔徑尺寸和孔徑分佈的多孔膜材料.對熱致相分離成膜過程中聚合物-溶劑體系的相圖測定，不同厚度的多孔膜形貌研究，不同x （聚合物-溶劑相互作用參數）體系所制備的多孔膜形貌等需深人研究Firstly, related to the problem about many kinds of geometric non - linear factors and shear deformation which are not differentiated definitely in a lot of studies, several kinds of beam element stiffness matrices respectively corresponding to geometric non - linear factors and shear deformation are derived as far as planar beam element is concerned and geometric non - linear factors of beam element in frame structure are analyzed systematically
本文首先針對眾多研究中對多種幾何非線性因素及剪切變形等不加以明確區分的問題，以平面桿單元為例，分別推出與多種幾何非線性因素及剪切變形相對應的桿單元剛度矩陣，系統闡述框架分析中桿單元的幾何非線性因素。Based on experimental research and theoretical analysis, investigations on the new type of joint are made systematically, the main contents and results include the following items. 1 four specimens of new joints between cfrt columns and steel beams are designed. by low - cyclic reversed load test, skeleton curves of new joints and shearing deformation in joint core area are studied, the influence of parameters, such as concrete cores, length of stiffener, and relative dimensions of column and beam, is discussed
本文在分析現有節點方案特點的基礎上，提出了角鋼加勁式節點方案，並採用試驗和理論分析相結合的方法，對這種新型節點進行了系統研究，主要研究內容與成果如下： （一）設計了4個新型方鋼管混凝土柱?鋼梁節點的試件，通過對新型節點的低周反復荷載試驗，研究了新型節點的骨架曲線和節點核心區剪切變形等，探討了內填混凝土、加勁肋長度和樑柱相對尺寸等對節點抗震性能影響。分享友人