等截面梁 的英文怎麼說

中文拼音 [děngjiémiànliáng]
等截面梁 英文
beam with constant cross sections
  • 等 : Ⅰ量詞1 （等級） class; grade; rank 2 （種; 類） kind; sort; type Ⅱ形容詞（程度或數量上相同） equa...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 梁 : 名詞1 （屋架中架在柱子上的長木） beam 2 （通常也指檁） purlin 3 （橋） bridge4 （物體中間條狀隆起...
  1. It is the key of ebfs, therefore, furthermore calculation about link are carried out in this thesis, introduced achieved research, summarized the affect of link on whole capability in the first, the second, numerical calculation are proceeded on link with ansys : with the purpose of discussing yielding mode critical length of link, established five different specimens ; with the purpose of discussing the influence of h / tw of web, b / tf of flange and h / b, established eighteen different specimens ; with the purpose of discussing the affect of stiffener, established four different specimens, and elaborated the affect of stiffener on link based on achieved test researches

    因此，本文對耗能梁段進行進一步計算分析，概述耗能梁段對整體性能的影響，並利用有限元程序ansys對耗能梁段進行數值計算：針對耗能梁段的屈服類型建立5種不同長度的模型，計算討論耗能梁段屈服類型的長度劃分；針對耗能梁段腹板高厚比、翼緣寬厚比以及梁段截面形狀等因素共建立了18種模型進行計算分析；針對加勁肋對耗能梁段的作用建立了4種模型，並結合已有的試驗闡述了加勁肋對耗能梁段的影響。
  2. Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed

    在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。
  3. This paper presents the structural design of the main bridge of lhasa river bridge, makes a deep - going study of the key techniques for design of the bridge, such as the reasonable span length ratio of each span of the 5 - span girder and arch hybrid structure, mechanical behaviour of the dual arch ribs, and section of the continuous girder tie beam, and also works out rigidity and stress conditions of the continuous girder tie beam and stress conditions of the concrete - filled steel tube arches of the main bridge

    摘要介紹了拉薩河特大橋主橋結構設計情況，對於五跨梁拱組合橋梁各孔跨合理的跨度比、疊拱的受力行為及連續梁系桿截面形式等設計中的關鍵性問題進行了深入的研究，給出了主橋連續梁系桿的剛度和應力情況、鋼管混凝土拱的應力情況。
  4. Consequently, on the basis of non - winkler foundation model, a finite - element method that utilizes foundation flexibility matrix into iterative calculation is proposed in this paper originated from the item " the optimal design theory and research of pile capping beam " sponsored by natural science fund of hunan province, which the continuity of soil mass can be accounted for under various boundary conditions, different loadings and irregular beam characters

    本文結合湖南省自然科學基金項目「樁基承臺梁優化設計理論與方法研究」 ，針對非文克爾地基（半空間、線性變形層或單向壓縮層地基模型等）上的樁基承臺梁，提出一種利用地基柔度矩陣來進行迭代的有限單元法，可充分考慮梁下土體的連續性，並對基礎與土體脫開、承臺梁截面變化、梁體邊界條件復雜、上部荷載類型變化以及梁下基樁承載力差異等情況進行分析計算。
  5. Finally, by the analysis of the highness of beam - bridge, the most dangerous section and the abutment cons truction of the circular hole castellated beam, the design and calculating method of the beam is given to promote the application of the beam

    最後，通過對圓孔蜂窩梁的梁橋高度、驗算截面以及支座構造措施等的分析，總結出圓孔蜂窩梁的設計計算方法，以促進這種梁的設計與應用。
  6. Based on the research to the stability variable cross - section beam, the bending defection differential equation of the variable cross - section beam in critical state of bucking is established. according to the edge condition of the structure, the differential equation is solved and bucking equation of variable cross - section beam is created. we can get the algorithm which can be used to calculate the equivalent inertia moment of the variable cross - section lattice structure when it is regarded as constant cross - section of solid web beam

    對變截面格構式構件的穩定性計算進行了初步的研究，通過建立變截面構件臨界狀態下彎曲變形的微分方程，根據變形邊界條件，得到了兩端鉸支的變截面梁失穩特徵方程，提出了幾種特殊形式的變截面格構式構件等效為等截面實腹式構件時等效慣性矩的計算方法。
  7. The effects to beam for its normal section flexural capacity and rigidity and ductibility as well as other properties is discussed with different polypropylene fiber and different concrete strength by the bending test study herein on the reinforced concrete beams and the polypropylene fiber reinforced beams

    本文通過對摻聚丙烯纖維砼配筋梁的試驗研究，分析討論了單筋矩形截面梁配筋率相同時，分別考慮聚丙烯纖維摻量和混凝土強度等級等因素對梁的正截面承載力、剛度及延性等幾個方面的影響。
  8. ( 3 ) it is known that load effect is not consistent with the section resistance incommon section continuous composite beam. a kind of composite beam with itsrational section size is suggested, which is consist of the t shape concrete beam andsteel girder. this kind of composite beam not only has enough carrying capacity, almost has same positive and negative resistance moment, but can decrease theamount of the steel

    （ 3 ）分析可知連續組合梁的跨中、支座截面處荷載作用效應及截面抗力規律不匹配，本文提出了採用t形混凝土梁和工字鋼代替一般的混凝土板和工字鋼的組合梁截面形式，並給出了截面尺寸比例，能使正負截面抵抗矩接近，符合組合梁受力特徵，減少了材料用量，滿足承載力和剛度等要求。
  9. Based on the research of influenced parameters on constant and varying depth solid web box girder before, the shear lag aroused by the parameters including width - span ratio, outstanding flange on base slab and the position of the tendons are further studied. the investigation show that shear lag values diminish along with the decease of width - span ratio and the departure from the symmetrical axis of anchor position, but outstanding flange is contrary to the former

    在前人對等截面、變截面實腹箱梁剪力滯效應影響參數研究的基礎上，本文進一步對腹板開孔的連續箱梁的寬跨比、底板翼緣伸出以及預應力錨固位置改變等參數對箱梁剪力滯的影響進行研究。
  10. Not only the load is considered, but also the distance, the span, the wide and the percent of the reinforcement is considered. the chosen section is also meeted the stiffness

    該公式不僅考慮到荷載大小、而且考慮了梁格的間距、跨度、梁寬、以及梁的配筋率等因素，且所選截面滿足剛度要求。
  11. As is well known, the effective width depends on several factors, such as the cross - section width, the height of web, the spacing of span and so on. we can conclude that width / span ratio ( overhang width / span and central width / span ) is the governing factor of the effective width

    影響箱形截面樑上翼緣有效寬度的因素很多，如上翼緣寬度、梁高、跨度以及結構體系等，通過大量計算表明寬跨比[翼緣部分寬度、箱室部分寬度與跨度的比值]是有效寬度的控制影響因素。
  12. The difference between axial compressive capacity of beam - column joints and that of columns is introduced when joints are strengthened by various measures. influence of shapes, spiral hoops and ratio of beam depth to side dimension of square column upon axial compressive capacity of beam - column joints is discussed. then economy and security of the relative article in current code are demonstrated and the design recommendations of beam - column joints are given

    本文通過6個不同強度等級混凝土樑柱節點試驗，了解在不同的加強措施情況下，節點區的軸心抗壓承載力與柱的理論軸心抗壓承載力的差異，探討了角鋼、螺旋箍筋及梁高與柱截面尺寸的比值h c對節點區軸心抗壓承載性能的影響，驗證了我國現行規范有關條款的安全性和經濟性，並且在此基礎上，為不同強度等級混凝土樑柱節點的設計提出了相關建議。
  13. Plastic theory suggests, the composite beam for the floorslab is suited lower flange, it s plastic limit moment cuts down by 52. 4 % than the composite beam for the floorslab is suited on the top flange. it s plastic limit moment lifts 8. 8 % than the steel beam, which is on the same condition

    塑性理論分析的結果表明，樓板位於鋼梁下翼緣形式的組合梁和樓板位於鋼樑上翼緣形式的組合梁截面相比較，其塑性極限彎矩降低52 . 4 ，和同等條件下純鋼梁截面相比較，樓板位於鋼梁下翼緣的組合梁塑性極限彎矩提高8 . 8 。
  14. Numerical simulation about section damage and voids under beam are carried through, and some numerical examples are used to explain the experimental phenomenon in chap 2

    對地基梁截面損傷、脫空等現象進行了數值模擬，並通過數值算例對第二章一些試驗現象作出了解釋。
  15. It is shown that the effects of the stiffness and inertia of the piezoelectric element that lead to higher first natural frequency on the natural frequencies of the beam are significant, and that of the elastic modulus of the bonding layer is small

    研究表明，壓電元件的剛度和慣量對梁的頻率影響很大，變截面智能壓電梁的一階固有頻率總是高於等截面梁的固有頻率。
  16. On the foundation of analysis a quantity of experiments and theory home and abroad, the paper give a calculation formula for the cross - section anti - bending limit load capacity of reinforced concrete beam. at the same time, the paper discusses the establishment of fatigue load chart for the bridge structure and presents its calculation of stress chart

    2 、在分析國內外大量試驗研究和理論分析的基礎上，給出了碳纖維布加固鋼筋混凝土梁正截面抗彎極限承載力的計算公式，詳細闡述了等幅疲勞荷載和變幅疲勞荷載下橋梁結構疲勞強度的計算方法。
  17. Regarding the rc beams subjected to concentrated load or even load and braced by bonding steel, an analysis is made on the relevant factors influencing maximum anchorage shear stress of steel sheet. the analysis is based on elastic theory and makes use of the formula for calculating anchorage shear stress of steel sheet. as indicated by the results, the maximum anchorage shear stress not only realtes to such parameters as height of cross section of rc beam and span but also relates to the thickness of adhesive layer, elastic modulus, thickness of steel sheet, and length of steel sheet. the present method will check maximum an chorage shear stress on the end of shear sheet so as to prevent rc beam from local damage. the present results will offer important reference for our country to further perfect bracing design by bonding steel method

    在彈性理論的基礎上，利用鋼板錨固剪應力計算公式，對在集中荷載或均布荷載作用下採用粘鋼加固的混凝土梁，分析鋼板錨固最大剪應力的有關影響因數.結果表明，最大錨固剪應力不但和混凝土梁的截面高度、跨度等參數有關，還和粘膠層厚度、彈性模量、鋼板厚度及鋼板長度有關.採用文中方法可以對鋼板端部最大錨固剪應力進行驗算，防止混凝土梁出現局部受拉破壞.研究結果為進一步完善我國粘鋼法加固設計提供重要的參考資料
  18. Constant section beam

    等截面梁
  19. By use of the fem program, the paper contrasts the differences of static calculation and stability analysis results of tapered portal frame structure analyzed by uniform section beam elements and tapered section beam elements respectively

    利用該程序，比較了分別用等截面梁元和變截面梁元對變截面剛架進行靜力計算與平面內穩定性分析的差異。
  20. The present study is for the key point of development of the single section continuous beam of middle - small span cad system ( sscbms ), which is based on database management

    本文是針對中小跨徑等截面連續箱梁橋結構設計而開發的基於數據庫管理的中小跨徑等截面連續箱梁cad系統? singlesectioncontinuousbeamofmiddle - smallspancadsystem （ sscbms ） 。
分享友人
分享到 Line

分享到臉書