等角偏線 的英文怎麼說

中文拼音 [děngjiǎopiānxiàn]
等角偏線 英文
isogonal
  • 等 : Ⅰ量詞1 （等級） class; grade; rank 2 （種; 類） kind; sort; type Ⅱ形容詞（程度或數量上相同） equa...
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 偏 : Ⅰ形容詞1 （不正; 歪斜） inclined to one side; slanting; leaning 2 （只側重一面） partial; prejudi...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  1. Because color isochromatic fringes appear in the stress model based on a plane polariscope in white light, we studied the problems systematically by a digital camera as image inputting device, digital image processing technique and bp artificial neural network. based on the work that has been reported before, a technique named five - step color phase shifting technique ( fcpst ) to acquire single isoclinics is presented

    根據白光入射時應力模型在偏振儀光學系統中的等色線條紋是彩色的特點，本論文採用彩色數碼相機作為數據採集與輸入設備，結合彩色信息圖像處理和bp神經網路等新技術，對上述兩個難題進行了系統的研究，獲得以下成果：在綜合前人工作的基礎上，提出獲得全場單純的等傾角相圖的五步彩色相移法。
  2. This paper analyses emphatically the position error and manufacture error of critical - angle prism the position error and aberration of object lens the position error and manufacture error of the polarization beam splitter the position error of the detector, and come out their relations

    著重分析了臨界角棱鏡位置誤差與製造誤差；物鏡的位置誤差與像差；偏振分束棱鏡的位置誤差與製造誤差；探測器的位置誤差等對離焦誤差信號的影響，並給出了理論曲線。
  3. According to the theory of light transmission, we derived the expression of rotation angle as a function of the dielectric constant conductivity of er fluid, and ( the angle between the electric vector of linearly polarized light and electric field ) from maxwell ' s equations and fresnel reflection, on the condition of several appropriate approximations and assumptions

    進而導出了非均相結構電流變液在外電場與光場交互作用下旋光角與（入射線偏振光振動方向與外加電場方向間夾角）及參數（為外加電場e 、分散顆粒介電常數、體積分數、絕緣油介電常數、位置矢量（ ? ）等量的函數）的西北工業大學應用物理系碩士學位論文摘要理論表達式。
  4. Based on geometry alignment data and speed difference, by stat. formula are established about the relation between downgrade, curve radius and deflection and speed change. then method to establish speed characteristic curve is present

    依據樣本路段的幾何線形數據和速度變化特徵，利用統計手段得出了縱坡坡度、平曲線半徑和偏角等線形指標與速度變化之間的關系公式，根據這些公式，給出了一定線形組合求解速度特徵曲線的方法。
  5. The in - plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and it ' s found that the in - plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5 %. the tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space. the

    研究結果表明：隨著縫紉密度、縫紉線直徑、最大纖維偏轉角和縫紉變形區寬度的增加，縫紉復合材料層合板面內等效模量逐漸降低，最大降幅一般在5 %左右；縫紉復合材料層合板的拉伸強度隨縫紉針距的增加而增大，隨縫紉行距的增加而降低，因此縫紉密度對拉伸強度的影響程度要看具體的縫紉針距和行距。
  6. Secondly, based on cutting edge geometric model and machining mode of mk6335a grinder, the rake face with constant normal rake angle and flank face with constant orthogonal clearance angle models of ball - end cutters are discussed. the cutting geometry angle parameters are solved and analyzed. moreover, the tool paths models of wheel which grinding are builded and the post - processing technique for coordination transfer is studied

    然後，基於刃口曲線模型、五軸數控磨床刃磨運動方式和微分幾何的直紋面概念，本文推導與建立了具有等法前角的前刀面和具有等主后角的后刀面的球頭立銑刀數學模型，並對球頭立銑刀的刀具角度如刃傾角、主前角、法后角、主偏角等參數進行了求解與分析。
  7. In new state standard < < machining center testing items - accuracy testing > > [ refering to iso / dis10791 ], issued in 1999, the test of straightness accuracy has been changed. now it becomes more scientific and reasonable. in old state standard, the testing of straightness accuracy of kinetic part only focus on vertical and " horizontal plane, and it only includes two linear errors ; but in new state standard, we not only measure those two linear errors, but also measure the errors of pitching, deflecting, and inclining of the kinetic part, so it includes two linear errors and three angle errors

    1999年公布的國標《加工中心檢驗條件?精度檢驗》 （參照iso dis10791訂）中，直線度等項的檢測做了更為科學的實質性更改，坐標移動的直線度以由只檢測垂直面和水平面內的兩個平移線值誤差，改為用移動坐標方向之外的另兩個坐標的平移線值誤差和移動部件繞三個坐標軸的俯仰，偏擺和傾斜三個角值誤差綜合表徵。
分享友人
分享到 Line

分享到臉書