筋縱 的英文怎麼說

中文拼音 [jīnzōng]
筋縱 英文
flaccidity of tendon and muscle
  • 筋 : 名詞1 （肌的舊稱） muscle2 [口語] （肌腱或骨頭的韌帶） tendon; sinew 3 [口語] （可以看見的皮下靜...
  • 縱 : Ⅰ動詞1 （釋放; 放走） release; set free; let go 2 （放任; 不約束） indulge; give oneself up to; l...
  1. The main components of the latter are multi - rib sandwich panels, including floor slabs and wall slabs. reinforced concrete conformation columns are set where the longitudinal walls and latitudinal walls intersect and copulative beams are set where floor slabs and wall slabs intersect. they play a role of linking and transferring loads, bearing a small part of loads at the same time

    無骨架體系的主要承重構件是密肋夾芯板（包括樓板和墻板） ，縱、橫墻相交處設鋼筋混凝土構造（連接）柱，墻板和樓板相交處設連系（圈）梁，連系梁和柱主要起連接和傳遞荷載作用，也承擔少部分荷載。
  2. The corbel ' s dimension should be ascertained as the manipulative condition of diagonal section. the amount of longitudinal reinforcement be ascertained on the basis of the flexure model, is obtained according to static for balance condition, the calculative expression of the load is obtained. and in terms of the design method in ultimate state the maximum load

    我國規范對于牛腿的設計規定，牛腿尺寸的確定以斜截面抗裂作為控制條件，縱筋用量的確定以彎壓破壞模型為基礎，根據靜力平衡條件得到承載力的計算公式，按照極限狀態設計方法計算得到，箍筋用量則按照構造要求確定。
  3. The application of resin bolt made in thread steel with left direction revolves and no lengthways physique at coal mine entry

    左旋無縱筋螺紋樹脂錨桿在回採巷道的運用
  4. Sliding displacement of beam longitudinal bars in staggered joints is smaller than in ordinary joints, and the beam bar " overstrength in staggered joints is more serious than in ordinary joints when shear force is equal in the two types of joints

    2在節點所受剪力相同的情況下，錯層節點中梁縱筋的粘結滑移比普通節點的要小，梁筋的超強更嚴重。
  5. Longitudinal topology by using double - strength steel, two rows of steel should pad diameter 25 mm with a short iron bars, designed to keep their distance

    縱向受力鋼筋採用雙層排列時，兩排鋼筋之間應墊以直徑25 ?的短鋼筋，以保持其設計距離
  6. Columns under axial compression and biaxial bending. in the beginning of the paper, it summarized the history and the actuality of the nonlinear analysis of special - shaped columns and the capability of the sliding of reinforcement anchoring. on the basis of related papers, the full path of stress - strain relation of concrete and the sliding of longitudinal reinforcement anchoring are all considered

    本論文主要內容是對鋼筋混凝土異形截面雙向壓彎柱（包括l形、 t形、十字形柱）進行非線形全過程分析，首先綜述了異形柱構件非線性分析以及粘結滑移性能研究的歷史與現狀，在有關文獻基礎上考慮了受拉縱筋和周圍混凝土的粘結滑移和混凝土應力?應變關系曲線的下降段。
  7. 2 the effects of load angle on load - bearing capacity of l, t and + - shaped columns under axial compression and biaxial bending are discussed. as for l and t - shaped columns, load angle has a great effect on bending capacity of them, mainly because of the asymmetry of sections. but for + - shaped columns, the effect of load angle on load - baring capacity is not much significant

    2討論了荷載角對l 、 t和十形柱受彎承載力的影響，表明l 、 t形柱由於截面不對稱，縱筋分佈不對稱，造成某一荷載角下承載力較大，而另一荷載角下承載力又很低。
  8. The content of the paper is nonlinear analysis of complete response process for t, l - shaped and " + " shaped section r. c. columns under axial compression and biaxial bending. on the basis of related papers, the full path of stress - strain relation of concrete and the sliding of longitudinal reinforcement anchoring are all considered, simultaneously, the restriction effect for concrete by thickening of stirrups is also included

    本論文主要內容是對鋼筋混凝土異形截面雙向壓彎柱（包括l形、 t形、十字形柱）進行非線形全過程分析，在有關文獻基礎上考慮了受拉縱筋和周圍混凝土的錨固滑移和混凝土應力?應變關系曲線的下降段，同時考慮到在箍筋加密區箍筋對混凝土的約束影響。
  9. 3. a space bond slip relation of reinforcements in either end of a member is proposed, based on one - dimensional bond slip model of reinforcements proposed by teng zhiniirmg from tsinghua university, the first - time loaded ascending stage ? curve of which model is modified as the line which parameters are not changed so as to simply the computation. the bond, slip is regarded as the boundary nonlinearity of a member

    3 、採用清華大學滕智明建議的一維鋼筋粘結滑移恢復力模型，但從簡化計算的角度出發，將首次加載的上升段曲線改為直線，並假定構件端部的諸多縱向鋼筋的滑移服從平截面假定，考慮由節點錨固區粘結滑移引起的構件端截面軸向和兩轉角附加變形。
  10. Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior

    分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大，實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著，而連接端板厚度及剪力連接程度的影響則不是太顯著。
  11. Based on measurement of strains of both horizontal stirrups in the joint core and longitudinal reinforcement passing througth the joint, in different stages, transfer mechanism and factors affacting seismic behavior of the joint, were analysed. under different shear compression ration, effect of axial force ratio on seismic behawior of the joint was also evaluated, static shear and seismic shear of the joint based on capacity design were investigated. on this basis, new governing criteria and conditions of seismic behavior of the joint were put forward

    通過對節點區水平箍筋以及貫穿節點梁、柱縱筋在不同受力階段應變的精細量測，對節點的傳力機理以及影響抗震性能的因素進行了分析研究；對不同剪壓比條件下軸壓比對節點抗震性能的影響規律進行了分析研究；對不同受力階段梁筋的粘結退化規律以及節點區的剪切變形進行了分析研究；對節點的靜力抗剪與建立在能力設計思路上的抗震抗剪問題進行了深入研究，提出了建立在新思路基礎上的節點抗震性能控制準則和控制條件。
  12. In the hogging condition, double bottom and the side shell remain the ultimate bucking strength, deck and upperwing tank remain the yield stress, and the other parts keep elasticity. then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels. in this regard, the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure. fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence. all possible collapse modes involed in collapse of stiffened panels, including overall buckling collapse, column or beam - column type collapse, tripping of stiffeners and local bukling of stiffened web are considered

    確定了船體梁整體破壞時的剖面應力分佈之後，關鍵在於確定板架的極限屈曲強度。本文充分考慮了在縱向彎曲、橫向壓力作用下加筋板可能發生的幾種破壞模式，即板架的整體屈曲破壞、樑柱形式的破壞、筋的側傾、腹板的屈曲並同時考慮了初始焊接殘余應力、初撓度的影響，使其更精確的計算加筋板的屈曲強度。對于加筋板中加強筋腹板的局部屈曲，採用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  13. On the contents of two sides abovementined, this paper attempts to do some initial researches from three angles as follows : 1, the analyses of anti - seismic features on longitudinal direction of the aqueduct l ) the seismic longitudinal effects are small. the vibrant characters are decided from the structure integration and rigidness of piers and main arch - ring of the aqueduct, so the following measures should be taken in order to weaken and isolate seismic influence : properly broadening the section sizes and adopting the high class concrete, lowering the height and barycenter of building, setting hoop steel bars so as to increase the plasticity of the concrete which can absorb the seismic energy and prevent the damages due to stress centralization on the linkages and changing place

    本文試圖就上述的這兩大方面的內容，從以下三個角度進行了初步研究： 1 、縱槽向抗震性能分析1 ）湯峪河吊桿拱支承結構的縱槽向地震效應較小；吊桿式拱架結構動力特性取決于槽墩和主拱圈的剛度，以及結構的整體性，故適當加大構件截面尺寸或提高砼標號，盡量降低結構的建築高度和重心，在構件連接和變截面處增設梗脅，按照約束混凝土的要求來加強箍筋的配置，增加砼的延性，以克服地震時構件連接和變截面處的應力集中造成的坡壞，並吸收大量的地震能量，從而起到隔震，減震的效果。
  14. The influence of such parameters as axial load index, aspect ratio and percentages of lateral reinforcement, on seismic performance of reinforced concrete frame column in hong kong and analyses the distribution relationships of flexural deformation, shear deformation and slippage of longitudinal reinforcement in joint zone

    根據試驗結果，討論了軸壓比、配箍率、剪跨比等參數對其抗震性能的影響，分析了水平荷載作用時塑性鉸區的彎曲變形、剪切變形和縱向鋼筋粘結滑移變形所產生的位移在框架柱總水平側移中所佔的比例及其變化規律。
  15. The prestressed continuous beam - arch composite bridges are a special structural system where the horizontal thrust of the arch rib is absorbed by a prestressed tie at deck level. in some cases, this type of structure is preferable because it does n ' t have the large thrust at the spring hi traditional arch bridges and the somewhat large bending moment and shear force in traditional beam bridges. as a result, the performances of the prestressing reinforcement can be efficiently utilized

    它利用拱肋承擔壓力，系梁預應力束抵抗拱端推力，吊桿及縱橫橋面系結構承受橋面荷載，既克服了傳統拱橋巨大的拱端推力，又改善了連續梁橋較大的彎矩和剪力的受力狀況，最大限度地發揮了拱梁混凝土和預應力鋼筋各自的特點，經濟效益顯著。
  16. ( 3 ) the beam stirrups are very important to the anchorage of the upper longitudinal bar in the beam outside the wall " s width

    節點區的寬梁箍筋對于凸出在墻外的寬樑上部縱筋的錨固具有比較重要的作用。
  17. Thus it is necessary to study moment resistance, rotation stiffness and rotation capacity of the joints. in this paper, six specimens on end - plate composite beam - to - column joints and two specimens on end - plate composite beam - to - column joints were designed to subject to static load. the factors of m - characteristics about semi - rigid composite joints, including bolts, profiled steel sheeting, beam, column, stiffen rib and reinforcement, are studied

    本文設計了6個端板型鋼-混凝土組合樑柱節點與2個端板型純鋼樑柱節點，通過對這些試件的靜力荷載試驗，重點研究了端板型鋼-混凝土組合節點的彎矩-轉角性能的影響因素，包括高強螺栓、壓型鋼板、型鋼梁、型鋼柱、加勁肋，以及混凝土板內縱向鋼筋配筋率等。
  18. Longitudinal crack formed when screw steel rebar is cold - bended was analyzed. the result indicates that ununiformly distributed silicate inclusions contributed to the longitudinal crack. protective measurements were also provided

    摘要對螺紋鋼筋由冷彎產生的縱向裂紋進行了分析，結果表明，硅酸鹽夾雜物分佈不均勻是造成螺紋鋼筋冷彎縱向裂紋的主要原因，並提出了相應的預防措施。
  19. In view of the rapid development of electric undertaking and a sharp increase of steel products consumption, the state development planning commission, the former state water resources and hydropower ministry and state energy ministry have been urging that the building of steel towers should be strictly controlled in the construction of transformer substations ; and warning that the need of the present 500kv power transmission and transformer trusses can hardly be satisfied by ordinary steel and concrete electric poles or prestressed concrete poles, which have endangered the operation and longevity of the high voltage transmitting line due to the common problem of cracks by gravity

    隨著電力工業建設的迅速發展，鋼材的用量急劇增長，為此，國家計委，原水電部和能源部一再強調在輸變電工程建設中，應從嚴掌握自立式鐵塔的建設。然而，一般的鋼筋混凝土電桿或與預應力混凝土電桿，較普遍地存在著縱向裂縫問題，嚴重影響了高壓輸電線路的安全運行及其使用壽命，已不能適應高壓輸電桿塔和變電構架的要求。
  20. Uses the high quality special molding manufacture, but becomes by the kneading board and the leg combination ; has the contour artisticly, firm is durable, does not need to maintain and so on the merit ; the kneading board and the inside lining stiffener spreads across, the bearing power optimizes, leg each strengthens processing, the average distributed load ; the surface uses galvanizes or the static electricity spurts models processing, is advantageous for cleanly, is not easy to pollute ; is suitable in various professions, the many kinds of situations, the use scope is extremely broad

    鋼制托盤：採用優質特種型材製造，由面板和支腿組合而成；具有外形美觀、堅固耐用、無須維護等優點；面板與內襯的加強筋縱橫交錯，承重能力更加優化，支腿各面均強化處理，平均分佈載荷；表面採用鍍鋅或靜電噴塑處理，便於清潔、不易污染；適用於各行業，多種場合，使用范圍極廣。
分享友人
分享到 Line

分享到臉書