管軸 的英文怎麼說

中文拼音 [guǎnzhóu]
管軸 英文
axle,tube
  • : Ⅰ名詞1 (管子) pipe; tube 2 (吹奏的樂器) wind musical instrument 3 (形狀似管的電器件) valve;...
  • : 軸Ⅰ名詞1. (圓柱形的零件) axle; shaft 2. (對稱部分的直線) axis 3. (圓柱形的纏繞器物) roller; spool Ⅱ量詞(用於纏在軸上的線以及裝裱帶軸子的字畫)
  1. The products includes : the tubes for structural purpose, fluid transportation tubes, the compo tubes, the heterogeneous tubes, the boiler tubes, tubes for hydraulic cylinders, the tubes for bearing, the tubes for petroleum well, and so on

    產品品種有:結構流體合金異型鍋爐液壓鋼體管軸油井用等。
  2. Bearings for derrick goosenecks - assemblies and components

    起重吊桿鵝頸管軸承.組件和部件
  3. Spirit level axis

    水準管軸
  4. The impact tests were carried out at the mid - span, and internal pressures of ompa, 5mpa, lompa and 15mpa were used in addition to the tests with water. the critical energy of perforation and the ballistic speed was measured, and the various types of rupture were identified from the section of the test specimens. force - time curves and internal pressure - time curves were obtained from experiment

    實驗中記錄了沖擊力時程曲線和內壓時程曲線,測量了鋼管軸向和周向橫截面的變形,得到了不同工況下的破壞模態、臨界穿透能量以及彈道極限速度,並找到了臨界穿透能量隨內壓的變化規律。
  5. Sea water lubricated stern tube bearing

    海水潤滑艉管軸
  6. Stern tube sealing oil pump

    管軸封油泵
  7. Abstract : the paper introduces the design of the water - lubricate stern rubber bearings d , deseribes the simple formulas for calculating the force applied on the marine stern bearings and the interral between bearings

    文摘:介紹了水潤滑橡膠承的設計,提供了船舶尾管軸承受力的計算公式及確定承間距的公式。
  8. Make sure to cut pipe keeping the cut plane perpendicular to the axle

    切割子時要使面與管軸保持垂直。
  9. Axis of the tube

    電子管軸
  10. When in position, square with the pipe axis, it is clamped in place by hydraulically - operated shoes

    到位后,使其與管軸垂直,用液壓操縱套接在適當的位置處將其夾緊。
  11. This article studies on damaged round steel tube members and at the same time both material nonlinearity and geometric nonlinearity are considered in calculation. numerical integration method is planed to be adopted to analyses the ultimate bearing cap acity of damaged round steel tube members

    本文研究同時考慮材料非線性和幾何非線性的特點,採用數值積分方法,對受損圓鋼管軸壓桿件的極限承載能力進行分析。
  12. According to the theory of numerical integration calculation programs are complied to calculate the ultimate bearing capacity of damaged round steel tube members. thus the impacts of different damage notch depths and different damage zone lengths on round steel tube members " stability ultimate bearing capacity can be discussed

    根據數值積分原理,編制受損圓鋼管軸壓桿件極限承載能力的計算程序,並對受損傷的桿件穩定極限承載力問題進行計算分析,討論不同損傷情況對桿件穩定極限承載力的影響。
  13. Through the pneumatic experiment of resemble model, it was discovered the fact that the flow speed was 1. 34 times faster than the natural wind speed at 565mm to the entrance section ( 37. 8 % of the length of diffuser in axial spacing ), and flux energy increased to 2. 41 times of the same area

    在相似模型的氣動特性實驗中,發現了在距相似模型入口565mm處(擴散管軸向長度的37 . 8 %處) ,氣流流速是前方相同面積來流風速的1 . 34倍,氣流動能增至前方相同面積來流風能的2 . 41倍。
  14. Hydraulic grease fitting : hydraulic grease fitting provides for lubrication of yoke sleeve bearing surfaces ( not shown )

    液壓潤滑油注入器:液壓潤滑油注入器為軛架套管軸承表面提供潤滑(沒有圖示) 。
  15. Through the combination of analysis and experiments, we get a certain sense of the function of net cover. setting the research of axis ei as example, this paper studies the effect of net cover

    通過計算分析與試驗相結合,以金屬軟管軸向剛度的研究為例,研究了網套的作用,對金屬軟網套的作用有了一定的認識。
  16. But method based on large deflection theory was proposed in this paper. accordingly, output force and displacement of each sma actuator under anticipative attitude was obtained as well as accurate coordinate of the center of the joint and deflection curve equation of the axis of the active catheter

    基於大撓度理論對主動導做了力學和運動學分析,相應獲得了預期姿態下各個sma驅動器上的輸出力和輸出位移,以及精確的關節中心位置坐標和導管軸線撓度曲線的具體形式。
  17. Oil bath type stern tube bearing

    油浴艉管軸
  18. Conducting ring, pipe heater, bearing, synchronous belt, conveyance belt and so on are of import brands

    導電環、加熱承、同步帶、輸送帶等採用進口產品。
  19. Oil lubricated stern tube bearing

    油潤式艉管軸
  20. The flow properties including chemical species distribution along axis of the nozzle were also presented

    並給出計算條件下噴管軸線上的物理量和化學組元分佈。
分享友人