節流孔板 的英文怎麼說

中文拼音 [jiéliúkǒngbǎn]
節流孔板 英文
choke flange
  • : 節構詞成分。
  • : Ⅰ動1 (液體移動; 流動) flow 2 (移動不定) drift; move; wander 3 (流傳; 傳播) spread 4 (向壞...
  • : Ⅰ名詞1 (片狀硬物體) board; plank; plate 2 (專指店鋪的門板) shutter 3 [音樂] (打拍子的樂器) ...
  • 節流 : 1. (節省經費開支) reduce expenditure 2. [工業] orificing; choke; throttle down, throttle back; throttle
  1. Measurement of fluid flow by means of pressure differential devices inserted in circular cross - section conduits running full - orifice plates

    用插入圓截面管道中的壓差裝置測量量.節流孔板
  2. Measurement of fluid flow by means of pressure differential devices inserted in circular cross - section conduits running full - part 2 : orifice plates

    用插入滿載的圓截面管道中的壓差裝置測量量.第2部分:節流孔板
  3. Measurement of fluid flow by means of pressure differential devices - guidelines for specification of nozzles and orifice plates beyond the scope of iso 5167 - 1

    用壓差裝置測量量. iso 5167 - 1規定范圍之外的噴嘴和節流孔板規范指南
  4. Measurement of fluid flow by means of orifice plates, nozzles and venturi tubes inserted in circular cross - section conduits running full

    量測量裝置用噴嘴和文丘里管測量充滿圓管的
  5. Abstract : various measurement methods of the capacity of gas discharge forpiston type compressor are analized and compared. the orifice choke device that is suitable for measurement in site is recommended emphatically. in combination with the example of measurement in site, the matters needing attention of measurement in site on the capacity of gas discharge for compressor are point out

    文摘:對活塞式壓縮機排氣量的各種測量方法進行了分析比較,著重介紹了比較適合於現場測量的裝置,並結合現場測量實例指出了壓縮機排氣量現場測量應注意的問題。
  6. Numerical simulation of a boiler primary - air flow through a throttle orifice - plate

    鍋爐一次風通過節流孔板時的數值模擬
  7. A solid - liquid fluidized bed has been designed and installed, which will be used in the heat exchanging and descale field. the experimental study for distributor design was carried out and the particles distribution in the tubes of the solid - liquid fluidized bed under different operating conditions was studied by using the ccd measure system. experimental results show that heterogeneous pores distributor which was arranged in the inlet chamber of the solid - liquid fluidized bed can improve the nonuniform distribution of particles in the pipe bundle under high flow rate. the nonuniform decreases by decreasing the mount of pore, but the solid holdup decreases too. the particles distribution is influenced by the position of the heterogeneous pores distributor

    實驗結果表明:在液固循環化床進口段安裝可調高度的變徑分佈,能在較高的速下,較好的改善固體顆粒在管束中的不均勻分佈;開率越小固體顆粒在管束中的分佈越均勻,但管束中粒子的平均固含率也越小;分佈的安裝高度對顆粒的分佈有很大的影響,在實驗范圍內分佈的安裝距離管束入口處越遠,顆粒在管束中的分佈越均勻。
  8. The technology of micro - electronics and calculation method was fully made in the system. how to improve the accuracy of standard orifice measurement is also discussed from the following aspects : the means of measurement and transmitter, online correction of measurement parameter and abnormal condition. all those means are used to overcome its shortcomings of less scale of measurement range, short period of checkout, more tache of maintenance and low accuracy of measure

    該系統充分利用微電子技術和計算技術以及通過實際現場總結的經驗,主要從測量與變送環採取的措施、相關參數的在線實時補償演算法、非正常情況的在線補償三個方面對如何提高量精度加以論述,盡可能地彌補差壓式量計量程比較小、檢定周期短、維護環多、準確度低的不足。
  9. Its role to regulating valves and flow - combination hole equivalent to the slip road to the flow distribution requirements

    其作用相當于調閥和等效量儀的組合,使各個支路的量分配達到要求。
分享友人