篩析終點 的英文怎麼說

中文拼音 [shāixīzhōngdiǎn]
篩析終點 英文
end-point of screening
  • 篩 : 名詞[書面語] （植物名） sedge
  • 析 : Ⅰ動詞1. （分開; 散開） divide; separate 2. （分析） analyse; dissect; resolve Ⅱ名詞（姓氏） a surname
  • 終 : Ⅰ名詞1 （最後; 末了） end; ending; finish 2 （指人死） death; end 3 （姓氏） a surname Ⅱ形容詞（...
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  • 終點 : 1 （一段路程結束的地方） terminal point; finishing point; destination 2 [體育] finish; 終點裁判員...
  1. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  2. By analyzing the characteristic of the flow field in overloading srm and comparing several existing experiment techniques, a convergence - fold tube facility was developed. the flow field in chamber of srm with high acceleration was simulated. some inhibitor ablation experiments were carried out in this test facility

    通過分析過載條件下流場的特點，提出並比較了現有過載地面模擬試驗技術的優缺點，最終確定了收斂?折管的模擬試驗方法，模擬了高過載條件下發動機燃燒室內的高濃度粒子流，利用該方法開展了高過載模擬沖刷條件下的絕熱層燒蝕特性研究及絕熱層抗沖刷能力的篩選試驗。
分享友人
分享到 Line

分享到臉書