簡單加性模型 的英文怎麼說

中文拼音 [jiǎndānjiāxìngmóxíng]
簡單加性模型 英文
simple additive model
  • 簡 : Ⅰ形容詞（簡單） simple; simplified; brief Ⅱ動詞1 （使簡單; 簡化） simplify 2 [書面語] （選擇人才...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 簡單 : 1 （不復雜） simple; uncomplicated; plain; simplicity 2 （平凡 多用否定式） commonplace; ordinary...
  • 模型 : 1 （仿製實物） model; pattern 2 （制砂型的工具） mould; pattern3 （模子） model set; mould patter...
  1. And the deficiencies are pointed out in present researches, such as highway capacity, level - of - service, influence factor of road alignments, etc. from these, it has confirmed that the thesis should be studied from rational analysis, quantitative analysis of level - of - service, impact on capacity of road alignments, setting - up simulation model, etc. the high - accuracy gps dynamic data acquisition appearance is proposed to be used for the first time to carry on the experiment of overtaking on two - lane highways, and experiment scheme is designed according to the driver ' s perceive to judge each overtaking course. based on the experiment data, it can get two important parameters of acceptant gap ? the critical gap of overtakable time headway and returnable time headway through data processing, which can offer the strong support to the research of two - lane highway capacity with qualitative and quantitative analysis. besides, the experiment methods is provided to observe overtaking ratio and to measure the

    研究中首次提出了運用高精度gps動態數據採集儀對雙車道公路上的超車行為進行觀測，設計了根據駕駛員感受度來衡量超車過程的實驗方案，並通過後期數據處理得到了超車過程中兩個重要的可接受間隙參數-可超車車頭時距和可回車車頭時距的臨界間隙值，為定性和定量分析雙車道公路通行能力提供有力的數據支持;同時，還提出了觀測超車率的實驗方法以及測量加速度干擾的實驗方案，統一了計算加速度干擾的時間統計間隔，為雙車道公路的服務水平量化研究奠定基礎;最後還簡單介紹了駕駛員問卷調查法和模擬程序中模型參數標定和驗證的數據採集方法。
  2. Fist of all, on the basis of the research of agone boffins, this author investigates the interaction mechanism of bolts and rock, and introduces the elastic ? lastic analytical resolution which is consist of the liner structure, the equivalent reinforced wall rock and the original wall rock in the simple loading from the equivalent well - proportioned view ; this solution is very important meaning for the engineering design. on the basis of coulomb friction model, the author introduces the finite element equation of the contact problem in order to provide the academic foundation for the application of msc. marc. finally, combining the engineering practice of the non - linear analysis of shield tunnel through yellow river of the south - north water transfer and using the model of friction, the author researched the evolution law of stress and displacement field in the structure of grouted rock bolts, and analyzed the effect to the stress and deformation of surrounding rock mass due to anchor supports

    首先，在前人研究成果的基礎上，對錨桿與圍巖的相互作用機理進行研究，利用全長錨固錨桿的中性點理論，從等效均化的角度來考慮錨桿對圍巖的加固作用，並推導了在簡單荷載作用下，含有襯砌、等效加固后的圍巖、原始圍巖三者的彈塑性解析解，對工程設計有著重要的參考意義；在數值模擬方面，以考慮錨固圍巖滿足規則化庫侖摩擦模型為基礎，利用虛功原理推導了接觸問題的有限元方程的計算格式，為開發運用大型商用有限元軟體msc . marc提供了理論根據，也形成了本文的理論基礎：最後，論文以南水北調東線穿黃隧洞穩定性分析項目為工程實例，利用本文所述的接觸問題的摩擦模型理論，對錨桿支護結構的應力場、位移場的變化規律進行了研究，分析了加錨支護對隧洞圍巖應力、變形的影響。
  3. In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test

    然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。
  4. Furthermore, to show the feasibility of our new approach, we briefly discuss the quantization of o ( n ) nonlinear sigma model, classical nonlinear sigma model and gross - neveu model which are constrained on a half line or supplemented by integrable boundary terms in chapter four

    第四章是為了進一步說明我們這一新方法的可行性，又分別對限制於半直線上或附加了可積邊界項的o （ n ）非線性模型、經典非線性模型和gross - neveu模型的自洽的poisson結構及量子化進行了簡單討論。
  5. The result is that this gas pool has simple structure, only forms a little nose - like structure at the district of fenghuangshan ; this pool belongs to delta front sub - facies sedimentary model, the underwater distributary channel and mouth bar is the better sedimentary microfacies ; the physical property of the reservoir is poor, the type of pore of the reservoir rock mostly are intergranular pore, intergranular solution hole and little are intercrystalline micropore ; the influential factors of pore structure and physical property are lithofacies, lithologic character and diagenesis ; the off - take potentia of all the testing well are deadly shortness, the wells have the worth of industrial recovery only under the condition of going through sand fracturing, and in the early of binging into production, the oil and sheath pressure drop rapidly, the production of the well drop rapidly

    研究認為該氣藏構造簡單，只在鳳凰山形成了一個小型的鼻狀構造；屬於三角洲前緣亞相沉積模式，水下分流河道和河口壩是有利的沉積微相；儲層物性差，儲層巖石的孔隙類型主要有粒間孔、粒間（內）溶孔及少量晶間微孔；影響蓬萊鎮組氣藏儲層孔隙結構及儲集性的因素有巖相、巖性條件及成巖作用；所有測試井自然產能都極低，必須經加砂壓裂后才有工業開采價值，且投產初期，油套壓下降較快，氣井產量下降迅速。
  6. ( 2 ) according to the advantages and disadvantages of plural information, the author analysed suited conditions and ranges of different predictable models. confirmed the mathematic model to be adopted in the studied areas. practice indicating : algebraic method can be used in those area where study degree is very lower. ( 3 ) author studied the mineralize prediction model of plural information based on cis, discussed the applications of different mathematic models, and also solved inaccurate which analysed only by normal maps in the past

    實踐表明，代數疊加法比較適合於地質研究程度較低的地區； （ 3 ）研究基於gis的多元信息成礦預測模型，探討基於不同數學模型之上的成礦預測適用條件和范圍，解決了以往傳統方法中僅通過紙質地圖進行簡單分析的不精確性； （ 4 ）通過對研究區成礦有利區預測成果的級別劃分，提出用結果分佈統計圖輔助分段的方法對結果值進行分段。
  7. And gave priority to the eular - bernonulli beam model, the simply and convenient analytical resolution for the response of the pipelines under dynamical traffic loads through the impulse function and the congruence method of the vibration form and so on. during the analysis of the chanmical results of the pipelines, the randomicity of the output of the pipelines response was taken into accout. so the stochastic process method was applied to describe the probability characters of the pipelines response, which made the results truer, more veracious

    本文採用eular - bernonulli梁模型和tomosimko梁模型對動力下kelvin粘彈性地基中管道固有振動性狀進行了分析，提出了各力學結果描述的解析式；並以eular - bernonulli梁模型為主，基於脈沖函數、振型迭加法等對管道在動力交通荷載作用下的管道響應問題提出簡單便捷的解析演算法；在管道受力結果的分析中，考慮管道響應輸出的隨機性，將管道響應用隨機過程來描述其概率特徵，使得結果描述更加真實準確。
  8. The beam - on - dynamic - winkler - foundation ( bdwf ) model was utilized to determine the lateral dynamic response of a pile with finite length in a viscoelastic soil. an analytical solution was obtained in the time domain for the vibration of a pile under a laterally cyclic force applied at the pile head. based on the solution, the transient response of the pile loaded by semi - sine force was acquired with superposition principle

    首先，基於動力winkler模型（ bdwf ）對粘彈性地基中有限長樁的水平動力響應問題進行求解，得到了單樁在樁頂受水平簡諧荷載作用下的時域解析解，並在此基礎上通過疊加原理得到了半正弦激振條件下的瞬態解析解。
  9. Through comparing the prediction result with that of traditional software growth reliability models, it could be seen that the double exponential smoothing technique not only was simple without complicated computation but also was able to provide more accurate prediction

    通過同傳統軟體可靠性增長模型的預測結果進行比較，可以看出雙指數平滑方法簡單，沒有復雜的數學計算，而且對通信軟體的失效行為的預測更加準確。
  10. The forecasts method including the forecast method of simple moving average, the forecast method of weighting moving average, the forecast method of single exponential smoothing, the forecast method of double exponential smoothing, the forecast method of multiplication model and the forecast method of monadic linear regression

    預測方法包括簡單移動平均法、加權移動平均法、一次指數平滑法、二次指數平滑法、乘法模型預測法和一元線性回歸方程預測法。
  11. Abstract : an integrated approach is proposed to investigate the fuzzy multi - attribute decision - making ( madm ) problems, where subjective preferences are expressed by a pairwise comparison matrix on the relative weights of attributes and objective information is expressed by a decision matrix. an eigenvector method integrated the subjective fuzzy preference matrix and objective information is proposed. two linear programming models based on subjective and objective information are introduced to assess the relative importance weights of attributes in an madm problem. the simple additive weighting method is utilized to aggregate the decision information, and then all the alternatives are ranked. finally, a numerical example is given to show the feasibility and effectiveness of the method. the result shows that it is easier than other methods of integrating subjective and objective information

    文摘:研究了結合主觀和客觀信息的模糊多屬性決策問題，其中主客觀信息分別由屬性權重的兩兩比較矩陣和決策矩陣組成.提出一種結合主觀和客觀信息的特徵向量決策方法，給出了2種求解基於主客觀特徵向量法的模糊多屬性決策方法.這種方法通過求解2個線性目標規劃模型得到最優屬性權重，然後，通過對決策信息進行簡單的加權集結，得到所有方案的排序結果.最後，通過一個算例說明了該方法的實用性和有效性.結果表明，該方法要比其他主客觀結合多屬性決策方法簡單
  12. An integrated approach is proposed to investigate the fuzzy multi - attribute decision - making ( madm ) problems, where subjective preferences are expressed by a pairwise comparison matrix on the relative weights of attributes and objective information is expressed by a decision matrix. an eigenvector method integrated the subjective fuzzy preference matrix and objective information is proposed. two linear programming models based on subjective and objective information are introduced to assess the relative importance weights of attributes in an madm problem. the simple additive weighting method is utilized to aggregate the decision information, and then all the alternatives are ranked. finally, a numerical example is given to show the feasibility and effectiveness of the method. the result shows that it is easier than other methods of integrating subjective and objective information

    研究了結合主觀和客觀信息的模糊多屬性決策問題，其中主客觀信息分別由屬性權重的兩兩比較矩陣和決策矩陣組成.提出一種結合主觀和客觀信息的特徵向量決策方法，給出了2種求解基於主客觀特徵向量法的模糊多屬性決策方法.這種方法通過求解2個線性目標規劃模型得到最優屬性權重，然後，通過對決策信息進行簡單的加權集結，得到所有方案的排序結果.最後，通過一個算例說明了該方法的實用性和有效性.結果表明，該方法要比其他主客觀結合多屬性決策方法簡單
  13. Simply operation mode, increased hoister, high efficiency stoner, steady presser sheller, super capacity paddy separator and strong function of rice miller ensuire this equipment a leading status among middle and small unit, indicate that currently it ' s the preferred equipment to the middle and small food - processing corporation in domestic

    其簡單方便的操作模式，加大流暢的提升機，高效寬大的清雜去石機，衡壓無油的壓鉈礱谷機，超大處理量的谷糙分離機和性能強大穩定的碾米機等保證了該設備在中小型機組中獨領風騷的地位，經廣泛的市場信息反饋表明其是當前國內中小糧食加工企業的首選機型。
  14. In order to make the mgb more easy - operating, ultrasonic testing simula - tion software was designed and developed, which has a good user - oriented interface and can simulate easily the inspection fields of planar transducer, focused transducer and angle beam transducer. it also can help inspectors analyze the inspection procedures and predict the feasibility of actual ultrasonic testing, then choose suitable inspection parameters. the side - drill hole and flat - bottom hole are commonly used in ultrasonic

    為了使多元高斯模型使用更加方便，本文設計並開發了基於多元高斯聲束理論的超聲檢測聲場模擬軟體，該軟體具有良好的圖形用戶界面，操作簡單，可方便地實現直探頭、聚焦探頭和斜探頭的檢測聲場模擬，可幫助檢測人員進行檢測過程的分析及結構件的可檢性預測，並選擇合適的檢測工藝參數。
  15. In order to improve dynamic performance of the control system in the assembly robot, according to acpmsm ( ac permanent magnet synchronous motor ) vector control model and the control idea about preview control, the paper presents a kind of control strategies that is composite of a primary pid ( proportion integral dif - ferenfial ) with a preview feed - forward compensation, its compensation is equivalent to linear combination of future adjacent difference, the simulation results show that it can not only improve the system tracking performance effectively, but also implement easily

    摘要為了提高裝配機器人控制系統的動態性能，依據交流永磁同步電機矢量控制模型，從預見控制的思想出發，提出了一種在原有pid基礎上外加預見前饋補償的控制方法，這種控制方法的前饋補償項取未來幾項目標值一階差值的線形組合，並模擬驗證了該控制方法對提高系統跟蹤性能的有效性和簡單可行性。
  16. This paper establishes a simple physical model of the non - linear temperature field of the metal material heated by monopulse laser and makes an analytical study on the physical model. the modeling results are basically in agreement with those of experiments

    建立了單脈沖激光加熱下金屬材料非線性溫度場的簡單物理模型，並進行了解析研究，所得結果與實驗結果基本符合
  17. Based on the continuous damage theory, considering the shear effect, the high - order shearing, flexural and in - plane deformation coupling model is built ; through the nonlinear fem analysis of rc beams strengthened with frp, the damage theory and damage course is researched ; compared with experiment results, it shows that the model is effective ; the fem analysis software is prepared to provide simple and effective method for the engineering application ; using the soft the frp strengthened beams before and after damage is modeled so as to provide the theory base for engineering application

    摘要基於連續損傷理論，考慮膠層的剪切效應，建立frp加固鋼筋混凝土梁的高階剪切彎曲及面內變形耦合模型，編制了有限元分析的軟體，進行非線性有限元分析；通過與已有的試驗結果進行對比，證明該模型的簡單，有效性；利用該軟體對未加固混凝土梁，初始進行加固的混凝土梁以及最大拉應變達到極限值時進行加固的混凝土梁等幾種情況進行數值模擬。
  18. Research result shows that the object - oriented geographic spatial model has stronger representative ability, is easier understood and accepted ; using the concept of geometric data type unify the process method of attribute and spatial data, and simplify entity query and analyses. the topologic relations between entities, which are not been stored in explicit formulation in the model, can be achieved through collective operation of geometric object ' s hypergraph model. compared with traditional his, the query and analyses ability of which based on new model are stronger

    研究結果表明，面向對象的地理空間模型具有更強的表現能力，並且容易被理解和接受；採用幾何數據類型的概念，可以使對非空間數據和空間數據的處理方法相統一，而且會使對實體的各種屬性數據（包括空間屬性）的查詢和分析模型更加簡單；對于面向對象模型中不顯式表示的地理實體間的空間拓撲關系，可以利用實體的幾何對象的超圖模型間的集合運算來求得；基於面向對象地理空間模型的實體查詢和分析，也比基於傳統gis數據庫查詢和分析具有強得多的功能。
  19. The secondary combustion, which has better controllability, and plays the most pivotal role on the overall performance of a strutjet, so the paper detailedly studied and analyzed the mechanism of fuel ' s atomization, the mechanism of fuel ' s spray burning, vital spray burning models and the combustion ' s controllability, combined with the author ' s practical investigation in the rbcc lab, finally, the author got a most simple and feasible method to control the spraying burning of liquid kerosene - - to set up an adjusting valve in the fuel pipeline

    文中重點對燃油的霧化機理、燃油的噴霧燃燒機理、主要的燃燒模型和燃燒過程的可控性，展開了詳細地分析研究，並結合在rbcc實驗室的實際研究，獲得了對燃油噴霧燃燒進行調節的最簡單、可行的方法，即在燃油管路上設置流量調節閥。於是燃燒組織問題轉化為對該調節閥的開度如何施加適當控制的問題。
  20. The wall was equaled to a beam - hinged frame. furthermore, the paper proposed a rigidity formula of continuous function based on damage theory. 4 ) on the basis of previous study on elastic stage, the paper put forward two orthotropic composite material models, twice reinforced model and bi - reinforced model, and also a simplified isotropic material model for engineering

    4 ）結合課題組前期的研究成果，就墻體在彈性階段的復合材料問題，提出兩種正交各向異性復合材料計算模型：二次單向纖維加強模型和雙向纖維加強模型，並在此基礎上，給出了適于工程計算的各向同性墻體簡化材料模型。
分享友人
分享到 Line

分享到臉書