粒徑分配 的英文怎麼說

中文拼音 [lìjìngfēnpèi]
粒徑分配 英文
size distribution
  • 粒 : Ⅰ名 （小圓珠形或小碎塊形物） small particles; grain; granule; pellet Ⅱ量詞（用於粒狀物）
  • 徑 : Ⅰ名詞1 （狹窄的道路; 小路） footpath; path; track 2 （達到目的的方法） way; means 3 （直徑的簡稱...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  1. The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites

    研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。
  2. Rubber compounding ingredients - carbon black - determination of pellet size distribution

    橡膠配合劑.炭黑.粒徑分佈的測定
  3. Based on the topographic features and data of sediment particle size of bed load at the fluctuating backwater reach of liujiaxia reservoir, the streamwise variation and variation process of median diameter of bed load during silting and scouring periods of the fluctuating backwater reach are analyzed, and it can be seen that the turning point for the sediment diameter variation from coarse to fine is located at the outlet of shigou gorge of the fluctuating backwater reach

    摘要根據劉家峽水庫變動回水區的河段地形特徵和歷年河床質泥沙粒徑級配資料，分析了變動回水區河段淤積和沖刷時，河床質泥沙中值粒徑的沿程變化和歷年河床質泥沙中值粒徑變化過程，並指出粒徑分佈由粗變細的轉折點在變動回水區寺溝峽峽口處。
  4. This paper gives a brief introduction of the formation mechanism of sma and the handing property of pavement from the aspects of theory and research. at the same time, this paper also studies the effect of aggregate size on road - related performance in some different grads. except, it also having inspected to use the sbs, the pe and the combination material of sbs and pe to analyze the influence to the function of material road

    瀝青瑪蹄脂碎石混合料（ sma ）以其溫度穩定性好、抗滑性能優良、低噪音、使用耐久等優點在公路建設中越來越受到重視，本文對sma組成特點，強度形成機理與路面使用性能從理論和試驗研究角度進行論述，並針對不同級配的瀝青瑪蹄脂碎石混合料，分析了粗、細集料的粒徑變化對其路用性能的影響，同時也考察了用sbs 、 pe 、 sbs和pe復合改性后的瀝青結合料對混合料的路用性能影響。
  5. In this paper, based on the experi ment and research data of the injected water quality in lunnan oil field in many years, the actual situation of the injected water in lunnan oil field is analyzed and discussed and the chemical indices ( content of the iron, dissolved oxygen, sulfide, carbon dioxide and oil and corrosion rote ), the bacterial index, the phys ical indices ( content and particle diameter of the suspended sub stance ) and the compatibility of injected water with formation water, etc. are evaluated one by one

    文章立足於多年來輪南油田注入水水質的實驗研究數據，對輪南油田注入水現狀進行分析討論；對化學指標（鐵含量、溶解氧、硫化物含量、二氧化碳含量、含油量、腐蝕率） 、細菌指標、物理指標（懸浮物含量、懸浮物粒徑）和注入水與地層水配伍性等進行逐一評定。
  6. Abstract : in light of thicker grain and smaller viscosity of debris flow, a segmented simulation of the debris flow with flume is presented. for the first time. more difficult resistance similarity is brought about by geometric rate without excessive coarsing and discontinuous similarity of sand grain composition in model is eliminated with different grain scale. on this basis the density similarity and sand conveying similarity are achived. the method presented is verified through a model test case

    文摘:針對水石流顆粒粗，粘性小的特點，提出了利用水槽進行分段模擬水石流的設想，首次通過幾何變率解決難度較大的阻力相似問題，改變了以往過度加糙的方式;通過變粒徑比尺的方法消除了模型沙級配不連續相似的問題，較好地實現了固體物質級配相似，達到了泥石流的密度相似和輸沙相似.通過水槽概化模型試驗實例，對本方法進行了驗證
  7. This text completely and systematically studies the status and the development of the pyrolysis and the fluidization of biomass, which distill the bio - oil in the domestic and international area, as well as the existing problems. this thesis primarily include following aspects : ( l ), by experimenting and measuring the energy ( heat value ) and the content of c, h, n chemical element of right 20 kinds of common biomass, on the base of the experimental result, and respectively established the biomass energy predict experiment formula with the element of h and c is from change, and passed the ro. os examination, which provides the basis and convenience for flash pyrolysis fluidization device energy to convert the rate to compute with biomass energy utilization calculation ; ( 2 ), proceeded the tg and dtg experimentation equal velocity ( 10 ? / min, 20 ? / min, 40 ? / min, 60 ? / min ) heating and constant temperature heating by studying on eight kinds of biomass samples, according to the experimental data and arrhenius formula, we established the dynamics model of pyrolysis of, then, using the goast - redfern and p function, we also solved the dynamics parameters and analyze out every kind of biomass ' s frequency factor and parameters of activation energy, and established the every kind of dynamics model of pyrolysis of biomass, all of these provide the theories and basis to make sure the reactor ' s flash pyrolysis work temperature scope design and the describing of pyrolysis reactor dynamics ; ( 3 ), in order to study and ascertain the process of heat completely getting to pyrolysis time of varied size biomass particles, we observed and measured the ratio of length and diameter ( l / d ) with the varied biomass through electron microscope, we concluded the l / d ratios usually is from 5. 0 to 6. 0, the average is 5. 3 ; ( 4 ), we studied the process of biomass transiting and the theory of complete pyrolysis time with the theory of complicated heat field, we got the time ( t ) of the varied size biomass particles arriving to complete pyrolysis, and we knew that the complete pyrolysis time and the time which get to the biggest production ratio are identical, all of these studies provide the theory base for design and forecasting the flash pyrolysis reactor solid state resort time ; ( 5 ), according to the above experiment result, synthesize to make use of the engineering the mechanics, engineering the material, machine the design to learn the principle, deduce, establish the theory of rotation cone flash pyrolysis reactor material resort time ( t ) and reasonable rotation velocity ( or frequency ) relation theory ; and ( 6 ), we gave the reactor ' s smallest cone angle certain, reactor cone wall strength design theory, the reactor production ability theory, the power design method and the critical rotation velocity theory

    本文較全面、系統地綜述了國內外生物質熱解液化制取生物燃油技術研究發展現狀及存在的問題，主要研究內容有： （ 1 ）實驗、測定了20種常見生物質的能量（發熱量）和c 、 h 、 n元素含量，根據實驗結果分別建立了以h和c為自變量的生物質能量預測經驗公式，並通過r _ （ 0 . 05 ）檢驗；為閃速熱解液化裝置能量轉化率計算和生物質能量利用率計算提供了依據和方便； （ 2 ）選擇了8種生物質試樣作了等加熱速率（ 10 min 、 20 min 、 40 min 、 60 min ）和恆溫加熱的tg和dtg實驗，根據實驗數據和阿倫尼烏斯公式建立了生物質熱解反應動力學微分方程，並採用goast - redfem積分法和p函數對其動力學參數進行了求解，解析出各種生物質的頻率因子和活化能參數，進而建立了各種生物質的熱解動力學模型，為科學確定反應器的閃速熱解工作溫度范圍及熱解反應動力學描述，提供了理論和依據； （ 3 ）為研究和確定不同尺度的生物質顆粒中心達到全熱解的時間，在體視顯微鏡下對不同粒度的生物質顆粒的長徑比進行了實驗觀察和測定，得出生物質的長徑比（ l d ）一般在5 . 0 6 . 0之間，平均為5 . 3的結果； （ 4 ）採用復雜溫度場傳熱學理論對生物質傳熱過程及充分熱解時間理論進行了研究，解析推導出了不同尺寸生物質顆粒中心溫度達到充分熱解溫度的時間（ t ） ，得出了理論推導的充分熱解時間與最大產油率的熱解時間相一致的結果，為閃速熱解反應器固相滯留時間設計和預測提供了理論依據； （ 5 ）根據上述實驗結果，綜合運用工程力學、工程材料、機械設計學原理，推導、建立了轉錐式閃速熱解反應器物料滯留時間（ ）與轉速（或頻率）合理匹配理論； （ 6 ）提出了轉錐式閃速熱解反應器的最小錐角設計、錐壁強度設計、生產能力設計理論和功率計算方法及臨界轉速理論等。
  8. The different ratio and dosage of composite surfactants were researched about the polymer latex ' s stabilization and structure. afterwards, the emulsion polymerization of tris, mma, and p ( mma - co - ptris ) were carried out. some different monomer ratio copolymer latex and homopolymer latex are prepared by emulsion polymerization used self - made organosilicone monomer - [ tris ( trimethylsiloxy ) silyl ] propylmethacrylate and mma

    用ir ， tem ， dma ，水滴接觸角測試等方法表徵所制備的均聚物和共聚物膜發現：採用有機硅表面活性劑與十二烷基硫酸鈉復配使用，用量在6 8 （相對單體量）可得到粒徑分佈均勻且穩定的均聚和共聚乳液。
  9. Beginning with the analysis of the effects, which are brought by the application of only one kind of pore - former and some other operating factors ( such as sintering temperature, warmth retaining time and so on ), on the properties of the beads, e. g., porosity, strength, size distribution of the beads and pores size, etc., these effects are discussed in detail and the relationship between the factors is studied thoroughly. the use of mpf ( multi - pore - former ) is introduced for the first time, which is of the most importance and significance in this paper

    研究從造孔劑選用和燒結過程對顆粒的孔隙率、機械強度、孔徑分佈及粒度分佈的影響入手，找出了造孔劑的種類及含量、燒結溫度以及保溫時間等因素對最終所得產品顆粒的性能影響及它們之間的相互關系，並首次提出將造孔劑復配使用來對填充法加以改進，無需擴孔處理，即能直接制備宏孔徑、高強度、小粒度、比表面大的多孔玻璃載體顆粒。
  10. Examined by tem, the production was slice shape in which there are many fine grains and the size of slices is 200nm ~ 2 u m and the most part of it is 500nm when the quality match ratio of aluminum nitrate and urea was 2. 5 : 1 and raw materials was ignited at 500 c. the size of slices is 200nm ~ 400nm when the quality match ratio of aluminum nitrate and urea was 2. 5 : 1 and raw materials was ignited at 300c

    經tem分析發現產物形貌呈片狀，當硝酸鋁和尿素在質量配比為2 . 5 ： 1 ，在500點燃時片狀產物尺寸約為200nm 2 m ，其中大部分粒徑約為500nm ，當硝酸鋁和尿素在質量配比為2 . 5 ： 1 ，在300點燃時產物尺寸約為200nm 400nm ，片狀產物內部由細小顆粒組成。
  11. The toad nutrient of floods increases as the sediment concentration increases, and there is nearly a linear relationship between them, by analysing the particle size of the sediment, we can conclude that the reason of the liner relationship is the resourse of flood nutrient and the sediment nature

    通過對洪水中下層泥沙做顆粒級配分析，推斷出這種結果主要是由洪水養分成因及洪水中下層泥沙粒徑特性決定的。
  12. Based on the chang - yu highway in julin province, this paper focus on gap - graded asphalt mixtures. aggregate grading of the gap - graded hma was designed by means of void design procedure. this paper give out a kind of new gradation of stone matrix asphalt. at the same time, this paper also studies the effect of aggregate size on road - related performance in some different gradings

    本文以吉林省長余高速公路為依託，從瀝青混合料的結構形態入手，利用體積法，對骨架密實型級配類型的瀝青混合料的級配進行研究，提出新型的瀝青馬蹄脂級配，並針對不同級配的瀝青馬蹄脂碎石混合料，全面分析了粗，細集料的粒徑變化對其各種路用性能的影響。
  13. A certain thickness of sand cushion of a certain size or gradation is paved between the foundation and ground in this new method. when earthquake happens the sand cushion will have plastic shearing strain, reducing the input of high frequency volume, thus consume the earthquake energy form substrate. it is showed in shaking table experiments that there is relevant slippage between foundation and sand cushion, which can prevent the seismic energy from being passed to the above structure and thus reduced the seismic role for the above structure

    在建築物的基礎與地基之間鋪設一定厚度、某種單一粒徑或級配砂墊層，在地震作用時砂墊層發生的塑性剪切變形，減少地震波高頻分量的輸入，從而消耗了下層傳來的地震能量；振動臺試驗表明，當振動發生時，基礎與砂墊層之間有明顯的滑移產生，這就對地震能量向上部結構的傳遞起到了隔斷作用，因而對上部結構起到了減震作用。
  14. The high precision separation device can use those mill beads which has small diameter and get high output

    高精度的分離裝置，可選配較小粒徑的研磨珠，獲得較高產能。
  15. Fluidized behaviors of ultra - fine powder caco3 of mean diameter 5 um in a spouted bed with a draft tube were investigated, studying the effects of geometry and operating parameters on the two - phase fluidized characters such as the initial spouted behavior, the solid circulation rate, the gas flow distribution in the spout and the annulus, and the solid flow in the annulus

    本研究以平均粒徑為5 m的caco _ 3超細粉為物料，對超細粉在導向管噴動床中的流化行為進行了系統的實驗研究，考察了床層結構和操作條件對起始噴動行為、固體循環速率、氣體在床層雙區中的分配以及固體顆粒在環隙區中的流動等氣固兩相流動特徵的影響。
分享友人
分享到 Line

分享到臉書