粗切刀 的英文怎麼說

中文拼音 [cūqiēdāo]
粗切刀 英文
heavy duty tool
  • 粗 : Ⅰ形容詞1 （長條東西直徑大的） wide （in diameter）; thick 2 （長條東西兩長邊的距離寬的） wide （i...
  • 切 : 切Ⅰ動詞1 （合; 符合） correspond to; be close to 2 （用在反切后頭 表示前兩個字是注音用的反切）見 ...
  • 刀 : Ⅰ名詞1 （切、割、削、砍、鍘的工具） knife; sword 2 （形狀像刀的東西） sth shaped like a knife 3 ...
  1. The influences of chamfer angle of pcbn cutting tool on the roughness and chip form

    刀具倒棱前角對粗糙度和切屑形態的影響
  2. Coarse - grained impact resistant grades for mining, working of stones and rock, building, mineral oil industry, percussion and hammer drill tips, inserts for mining cutters, chisels, asphalt cutters, picks, inserts for concrete - working, hammer cheeks rolls, hot wire rolling, ball pressure dies, brake blocks

    粗晶粒度的抗沖擊牌號，適用於采礦工業、採石、建築、石油鉆探工業、鉆頭和錘頭、礦刀的襯墊、鑿子、瀝青切刀、風鎬、混凝土製造的襯墊、錘子的滾軸、熱軋軋輥、子彈壓力沖模、剎車片。
  3. The roughing cut, to remove the greater part of the excess material, should be reasonably heavy, that is, all the machine, or cutting tool, or work, or all three, will stand

    粗切削因為要去除大部分的余料，切削力量肯定是相當大的，這就意味著，整個機器、刀具、工件或這三者都要能承受得了。
  4. Firstly, tool - path for rough machining is generated through setting cutting depth, machining allowance and other parameters. interferences are resolved through raising the z - components of the generated cl point according different kind of situations. and then two methods to generate tool - path for finish machining is presented

    首先通過設定切削深度和加工余量等參數生成遞歸分割曲面模型的粗加工刀具軌跡，對刀具軌跡生成過程中多種抬刀情況分別進行處理，避免粗加工中的過切干涉。
  5. Applies taguchi method for optimizing the turning operations about the depth of cut, cutting speed and feed rate after obtaining every factor with different level ' s mean surface roughness and s / n

    摘要應用田口法對切削速度、背吃刀量以及每齒進給量三個主要影響表面粗糙度的因素進行分析，求出各個因素不同水平的平均表面粗糙度和信噪比（ s / n ） ，得到最優切削參數。
  6. It is considered as the main reason that the fine silicon is easier to be pressed into the matrix and to cooperate with the matrix deformation in the machining of alloy, but the coarse silicon breaks, drops out and displaces usually during the machining, which results in strenuous friction between the tool and the work and various defects in machined surface

    造成這種影響的主要原因在於細小的硅粒比較容易協同基體塑性變形和被刀具壓入切屑和已加工表面，而粗大的硅塊往往發生解理破碎、脫落和位移，直接與刀具發生強烈摩擦並使已加工表面存留許多缺陷。
  7. Slitting cutter with coarse teeth

    粗齒切口銑刀
  8. Dice the mushrooms and carrots. chop finely the thick broad - beans, and still more finely the scallion and ginger. drop the mushrooms, bamboo shoots, diced carrots, and green soybeans into boiling water and cook till done, remove

    冬筍切片，剞十字花刀后切粗長條，冬菇胡蘿卜切丁，鄲縣豆瓣剁碎，蔥姜切末，冬筍冬菇胡蘿卜丁青豆下開水中煮透撈出
  9. Using rotating knife in the thread trimmer system. providing stable and perfect trimming effect for any specification of thread

    切線機構採用回轉刀，從細線至粗線皆有安定切線性能。
分享友人
分享到 Line

分享到臉書