粗塗料 的英文怎麼說
中文拼音 [cūtúliào]
粗塗料
英文
coarse stuff- 粗 : Ⅰ形容詞1 (長條東西直徑大的) wide (in diameter); thick 2 (長條東西兩長邊的距離寬的) wide (i...
- 塗 : Ⅰ動詞1 (抹) spread on; apply; smear 2 (亂寫或亂畫) scrawl; scribble 3 (抹去) cross [blot; s...
- 料 : 名詞1 (材料; 原料) material; stuff 2 (喂牲口用的穀物) feed; fodder 3 (料器) glassware 4 (...
- 塗料 : coating material; paint; coating; daubing; dope; moldwash
-
Or on coarse wool cloth, and sometimes on silk for precious ones. the base of the painting is prepared using a paste of animal glue and fine lime. after the paste dries, carbon and paints using natural mineral and plant colors, such as yellow, mineral green, azurite and cinnabar, are applied
唐卡,即布畫,是藏傳佛特有的一種繪畫藝術,一般以亞麻布或粗毛布為底布,較為珍貴的由以絲綢為底布,塗以動物膠和細石灰調合而成的糊狀物,乾燥後用木炭條起稿,然後以石黃石綠石青硃砂等不透明的礦物和植物質顏料著色。The buddhas were only roughly carved in the rock, which was then covered in a mud plaster mixed with straw and horsehair molded to depict the folds of their robes and then painted in bright colors
佛像只粗略雕刻在巖壁上,再包覆一層灰泥,摻雜稻草和馬毛,用來形塑佛像法袍縐摺,再塗上鮮明的顏料。Surface roughness of coatings affects the bioacitivity of materials, in order to change the roughness of coatings, the granularity of coating powders was changed firstly. nanometeral anatase titanium dioxide powders were prepared by hydrolysis of titanium - tetrabutoxide with ethanol in this paper. the main particle size is between 5nm and 10nm, while the size of ordinary titanium dioxide powders is about 100nm
為了改變塗層表面的粗糙度,實驗中從改變塗層粉末的粒度入手,以鈦酸丁酯為原料,通過醇鹽水解法制備了納米級銳鈦礦型tio _ 2超細粉,粒徑約為5 10nm ,而普通二氧化鈦粉體的粒徑多在100nm左右。Coated abrasives - grain size analysis - part 2 : determination of grain size distribution of macrogrits p12 to p220
塗附磨具用磨料粒度分析第2部分:粗磨粒p12 p220粒度組成的測定Test methods for coarse particles in pigments, pastes and paints
顏料,糊劑及塗料中粗顆粒的試驗方法Preparation of steel substrates before application of paints and related products - surface roughness characteristics of blast - cleaned steel substrates - method for the calibration of iso surface profile comparators and for the determination of surface profile - stylus instrument procedure
塗塗料和有關產品前鋼基的制備.噴丸處理鋼基體的表面粗糙度.第4部分: iso表面輪廓比較儀的校準方法和表面輪廓的測定方法.觸針儀法Preparation of steel substrates before application of paints and related products. surface roughness characteristics of blast - cleaned steel substrates. part 4 : method for the calibration of iso surface profile comparators and for the determination of surface profile. stylus instrument procedure
塗料和有關產品使用前鋼基片的制備.噴丸處理鋼基片的表面粗糙度特性.第4部分: iso表剖面比較儀的校準方法和表剖面的測定方法.觸針儀器的程序Preparation of steel substrates before application of paints and related products. surface roughness characteristics of blast - cleaned steel substrates. part 2 : method for the grading of surface profile of abrasive blast - cleaned steel. comparator procedure
塗料和有關產品使用前鋼基片的制備.噴丸處理鋼基片的表面粗糙度特性.第2部分:噴砂處理表剖面的定級方法.比較程序Standard test method for determining the adherent coating on coarse aggregates
粗集料上粘附塗層測定的標準試驗方法Typical temperature is 800 - 1000 in cvd diamond process, while the high temperature limits its application in optical window and coating such as gaas, zns etc. low temperature can not only make diamond crystal nucleus finer, reduce surface roughness of diamond films and lessen light dispersion, but also eliminate thermal stress
化學氣相沉積金剛石膜過程中,襯底的典型溫度為800 1000 ,這么高的溫度限制了其作為gaas 、 zns等低熔點光學材料窗口和塗層的應用。低溫沉積金剛石膜不僅可以使晶粒細化,降低表面粗糙度,減小光的散射作用,而且可以消除熱應力。Gently sand the plastic to provide a key for the paint
用砂紙在塑料上輕輕打磨出粗糙面以便塗顏料。Preparation of steel substrates before application of paints and related products - surface roughness characteristics of blast - cleaned steel substrates - method for the grading of surface profile of abrasive blast - cleaned steel - comparator procedure
塗料和有關產品使用前的鋼基體的準備.噴丸處理鋼基體的表面粗糙度.噴砂處理鋼表面輪廓的定級方法.比較方法Preparation of steel substrates before application of paints and related products - surface roughness characteristics of blast - cleaned steel substrates - method for the calibration of iso surface profile comparators and for the determination of surface profile - focusing microscope procedure
塗料和有關產品使用前的鋼基體的準備.噴丸處理的鋼基體的表面粗糙度. iso表面輪廓比較儀的校準方法和表面輪廓的測定方法Preparation of steel substrates before application of paints and related products. surface roughness characteristics of blast - cleaned steel substrates. part 3 : method for the calibration of iso surface profile comparators and for the determination of surface profile. focusing microscope procedure
塗料和有關產品使用前鋼基片的制備.噴丸處理鋼基片的表面粗糙度特性.第3部分: iso表剖面比較儀的校準方法和表剖面的測定方法.顯微鏡的調焦程序分享友人