粗度 的英文怎麼說

中文拼音 [cūdù]
粗度 英文
coarseness
  • 粗 : Ⅰ形容詞1 （長條東西直徑大的） wide （in diameter）; thick 2 （長條東西兩長邊的距離寬的） wide （i...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. Beryllium powders with the same particle size and various contents of beo were prepared by pre - sintering - acid washing processes initiatively and the influence of beo alone on o mys of beryllium was observed and some new results have been obtained - compared with the content of beo, the distribution of beo in beryllium has more critical influence on mys ; finely dispersed beo along the grain boundaries and in the matrix results in the dispersion strengthening of beryllium matrix and thereby the higher mys value ; on the contrary, the coarser beo particles clustering on the grain boundaries results in negative influence on o mys

    開創性地用預燒結? ?酸洗工藝制備了相同粒度、不同beo含量的鈹粉，從而開展了beo含量單獨對鈹材_ （ mys ）影響的研究，得出一些新的結果：與beo含量相比， beo在鈹中的分佈狀態對_ （ mys ）的影響更大。沿晶界、晶內彌散分佈的較細小beo對基體鈹有彌散強化作用，使_ （ mys ）即較高；如果beo較粗大地成簇狀聚集在晶界，反而對_ （ mys ）有不良的影響。
  2. Nanometer scale surface roughness measurement based on afm

    基於原子力顯微鏡的納米級表面粗糙度測量
  3. The model of the itr between a1n and cu is built by using the acoustic mismatch model, amm and diffuse mismatch model, dmm. because there is a limit of roughness and temperature in amm and dmm, the data of the theory model that is directly built by amm and dmm is far from the experimental data. accordingly, with dmm and traditionary methods, the mathematics model is posed by contrast and analyses of the experiment data

    由於聲失配理論和散聲失配理論對溫度和粗糙度有很嚴格的要求，所以直接建模所得的理論數據與實驗數據有很大的差距，本文採用聲失配理論與傳統研究方法相結合，通過與實驗數據的分析擬合，提出了修正的數學模型，預測誤差有了大幅度的提高。
  4. When analyzing the intensity of the drum with the simple numeration and the analogism or the shell theory, the calculative result is not very precise and it " s difficult to describe the nice change of the stress distinctly

    採用粗略的簡化計演算法及類比法或者用板殼理論等方法對滾筒進行強度分析，計算結果不是很精確，應力的細微變化也很難描述清楚。
  5. No. 1 fu an st. ying ko, taipei hsien, taiwan

    研磨加工效率高耐用面粗度佳。
  6. In this paper, the measuring of the main parameters as slub length, slub multiple and slub pitch and their imitative design method are described

    摘要介紹了竹節紗竹節長度、粗度、竹節間距等主要規格參數的測定與仿樣設計方法。
  7. Determination of fiber coarseness

    纖維粗度的測定
  8. Weight: the terms bold, medium, light are used to indicate thickness of line.

    線粗：黑體、中粗體和細長體這些術語，都是用以指明線的粗度。
  9. 1. 2. bakelite substrate : vibration absorption, a reduction of wheel abrasion and the improvement of surface roughness

    1 .電木基材：吸震作用減少砂輪磨耗改善表面粗度。
  10. After investigated the morphological diversity, biological and economic qualities of the samples, the main data of number of shoots, height and thickness of the shoot, number of fruit - breeding branches per shoot, number of fruit on a fruit - breeding branch were acquired, which could be used to establish the quality of initial materials in breeding

    通過對樹莓的形態多樣性，供試材料的生物和經濟性狀的綜合評價，獲得了枝條的數量、高度和粗度，枝條上結果枝的數量，結果枝上漿果的數量等主要數據，這些數據可以確定用於育種的原始材料的優劣。
  11. Forging die is the most suitable for high speed milling application, because of its high hardness i material and lower surface roughness

    而各式模具中又以?模最為適合，因其模具材料硬度較高且模穴表面粗度要求較低。
  12. High grinding efficiency, excellent durability and surface roughness

    研磨加工效率高耐用面粗度佳。
  13. Excellent roughness for the grinding surface reduces the working process afterward

    研磨面粗度好，減少后工程加工
  14. Rough measuring machine

    表面粗度儀
  15. Fibre furnish analysis of paper, board and pulps - determination of fibre coarseness

    紙紙板和紙漿纖維配料分析.纖維粗度的測定
  16. Pulps - determination of fibre coarseness by automated optical analysis - polarized light method

    紙漿.用自動光學分析測定纖維粗度.偏振光法
  17. It can be customized with a customer demand, and consider surface roughness and polishing efficiency

    可隨客戶需求設計，兼顧加工時的面粗度及加工效率。
  18. As a result, you typically want to identify large - grained business functions and define large - grained services

    所以，您通常還需要識別粗度的業務功能和定義粗度的服務。
  19. The method uses frequency components of the marks and the corresponding amplitudes as the indexes for the quantitative evaluation, which can be obtained directly from the surface roughness measurement system

    此法以振紋之頻率成分及其振幅為量化之指針，其值可直接由三維表面粗度量測系統求得。
  20. Wet grinding is adopted within the possible range if it cannot help, a spray or air will be blew and delivered. because coolant will have a lot of influence on the roughness of grinding surface, surface precision, wheel sharpness and wheel life

    在可能范圍內採用濕式研磨為宜若不得已，加噴霧或空氣吹送，因研磨液對研磨加工面粗度表面精度砂輪銳利性及砂輪壽命都有很大的影響。
分享友人
分享到 Line

分享到臉書