粗晶粒狀 的英文怎麼說

中文拼音 [cūjīnglìzhuàng]
粗晶粒狀 英文
macromeritic
  • 粗 : Ⅰ形容詞1 （長條東西直徑大的） wide （in diameter）; thick 2 （長條東西兩長邊的距離寬的） wide （i...
  • 晶 : Ⅰ形容詞（光亮） brilliant; glittering Ⅱ名詞1. （水晶） quartz; （rock） crystal 2. （晶體） any crystalline substance
  • 粒 : Ⅰ名 （小圓珠形或小碎塊形物） small particles; grain; granule; pellet Ⅱ量詞（用於粒狀物）
  • 狀 : Ⅰ名詞1 （形狀） form; shape 2 （情況） state; condition; situation; circumstances 3 （陳述事件或...
  • 粒狀 : graininess; granulose; granular粒狀冰 [水文] granular ice; 粒狀材料 bulk material; granular mater...
  1. Beryllium powders with the same particle size and various contents of beo were prepared by pre - sintering - acid washing processes initiatively and the influence of beo alone on o mys of beryllium was observed and some new results have been obtained - compared with the content of beo, the distribution of beo in beryllium has more critical influence on mys ; finely dispersed beo along the grain boundaries and in the matrix results in the dispersion strengthening of beryllium matrix and thereby the higher mys value ; on the contrary, the coarser beo particles clustering on the grain boundaries results in negative influence on o mys

    開創性地用預燒結? ?酸洗工藝制備了相同粒度、不同beo含量的鈹粉，從而開展了beo含量單獨對鈹材_ （ mys ）影響的研究，得出一些新的結果：與beo含量相比， beo在鈹中的分佈狀態對_ （ mys ）的影響更大。沿晶界、晶內彌散分佈的較細小beo對基體鈹有彌散強化作用，使_ （ mys ）即較高；如果beo較粗大地成簇狀聚集在晶界，反而對_ （ mys ）有不良的影響。
  2. The results show that under the same lapping conditions the si3 n4 ball has the lowest material removal rate and the best roundness and roughness, followed by zro2, al2o3, and sic ball

    結果表明：在相同的研磨條件下，具有長柱狀晶粒的氮化硅陶瓷球加工速率最低，但圓度和表面粗糙度最容易控制；氧化鋯和氧化鋁陶瓷球表面質量次之，碳化硅陶瓷球加工速率最高，圓度和表面粗糙度最難控制。
  3. The cmp experiment was carried out systematically on litao3 wafer. the polished surface foughness and material removal rate in different polishing conditions were measured and the effects of polishing pad material and its condition, pressure, rotating speed of the polishing plate, the type and size of abrasive, and the properties of the polishing slurry on the surface routhness and material removal rate were analysed in details

    通過對鉭酸鋰晶片的化學機械拋光過程的實驗研究，通過測量鉭酸鋰晶片在不同拋光條件下的表面粗糙度和材料去除率，詳細分析了拋光墊材料和狀態、拋光壓力、拋光盤轉速、磨料種類及粒度、拋光液組成等幾個因素對拋光表面質量和材料去除率的影響規律。
  4. The transformation of the platelike ? - alfesi to spherical a - alfesi during homogenization is markedly accelerated by the addition of minor mn and cr in al - mg - si alloy, as well as the recrystalization of alloys during hot extrusion has been inhibited, and ? " strengthening phase improved to precipitate in the process of aging

    合金鑄錠均勻化處理過程中，形成含mn 、 cr的第二相al （ mnfe ） si和al （ mncrfe ） si等，這些顆粒加速長棒狀的b - alfesi相向尺度較小的粒狀的- alfesi相轉化，減少了粗大結晶相對合金性能的不利影響。
分享友人
分享到 Line

分享到臉書