粘度值 的英文怎麼說

中文拼音 [niándùzhí]
粘度值 英文
k value
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. In this paper, glycidyl ether, which was high epoxide value and low viscosity, was synthesized from 2 - trimethylene glycol, epichlorohydrin and the normal butyl alcohol by phase transfer catalyst based on the orthogonal experiment design

    摘要採用1 ， 2 -丙二醇、正丁醇和環氧氯丙烷為原料，在相轉移催化劑的作用下反應，通過正交實驗合成了的高環氧值、低粘度的混合醇縮水甘油醚。
  2. The relational expression of the speed difference of drum and spiral propeller ( 0 ) and the difference of drum speed and input speed of the differential gear ( 1 ) is derived

    由於鉆井液的比重和粘度是隨井下情況變化的不確定值，且現場對鉆井液的處理量時有變化，需隨時調節0或1以調節離心機的處理能力和效果。
  3. In this paper, the viscosity changes of hydroxy ethyl cellulose sol caused by a kind of mixed salt were studied, which provided valuable basic data and an adapting equation for its practical application

    摘要研究了一種混合鹽的存在使羥乙基纖維素溶膠粘度變化的情況，為其實際應用提供了有價值的基礎數據和擬合公式。
  4. Plastics - polyamides - determination of viscosity number

    塑料.聚酰胺.粘度值的測定
  5. At the same time we study, analysis and discuss the action that non - linearity - stickiness - springiness and crazing damage of the pmma sample under creep though making us of the knowledge about the high molecule physics the damage theory of material of rheology of bodies with defects. through the study and theory analysis of single - axes stretching experiment in pmma sample under creep, take the surface crazing damage density of pmma sample as an variable, to look for a commonly rule that the crazing damage of pmma, and to offer a feasible damage model for the sake of study that of pmma ' s remoteness damage

    同時運用高分子物理、含缺陷流變性物體的材料破壞理論等知識，對無孔洞pmma試件和有孔洞pmma試件蠕變條件下非線性粘彈性行為及其銀紋損傷現象進行了研究、分析與探討，通過對蠕變條件下的pmma試件的單軸拉伸實驗研究和理論分析，以pmma試件的銀紋損傷面密度值為損傷變量，來嘗試尋求pmma銀紋損傷的一般規律，為研究pmma的細觀損傷提供了一種可行的損傷模型。
  6. On the basis of experiment, by using the exponential viscous model, a flow constitution equation of the pattern material ( w ax stock ) used in investment casting has been established. by applying it to the n umeric al simulation system, the numerical simulation on die - filling process of the fus ible pattern material ( wax stock ) used in investment casting has been successfully realized

    在實驗基礎上，採用冪律粘度模型建立了熔模鑄造用模料的流動本構方程，將其應用到數值模擬系統中，成功地實現了對熔模鑄造用模料充型過程的數值模擬。
  7. To illustrate the effect of variable feed rate, the pressure and power draw changes with fluctuations in feed rate are calculated on the table below

    瞬間的壓力變化及峰值出現是由熔融粘度瞬間變化導致的。
  8. Moreover, the resulted prediction model of foam size of the closed cell aluminum foam was verified by comparison to the experimental results from the foaming process at different foaming conditions, and the predicted bubble diameter is in good agreement with the experimental ones, the relative error distributes between - 5. 04 % and 6. 32 %

    當入射空氣的壓強、氣流量，液面高度，出氣孔直徑增大時，氣泡直徑隨之增大；當出氣孔數量，液體粘度增大時，氣泡直徑減小，表面張力對氣泡直徑的影響可以忽略不計；靜態條件下液體表面氣泡直徑的預測值和實驗測量值符合得較好，相對誤差分佈在- 5 . 04 % ~ 6 . 32 %之間。
  9. Fucoidans is a unique class of sulfated polysaccharide with many special activities. and oligosaccharides from fucoidans are more valuable than the whole fucoidans due to their low conglutination and high solubility. in this paper, samples are collected from different coastal areas in qingdao in order to obtain bacteria producing fucoidanase

    巖藻聚糖硫酸酯是一種獨特的活性多糖，而由其降解得到的寡糖，由於粘度低，溶解性好等優點而比原生的巖藻聚糖硫酸酯更有利用價值。
  10. Plastics - cellulose acetate in dilute solution - determination of viscosity number and viscosity ratio iso 1157 : 1990 ; german version en iso 1157 : 1999

    塑料.稀釋溶液中的乙酸纖維素.粘度值和粘度比的測定
  11. This article brings forward a way of computer control system. it can not only control resin viscosity online and display control curve, but also change target value through friendly control interface. it can be operated easily and it will greatly improve control effect

    本文提出樹脂粘度計算機控制系統方案不但能在線測量和控制樹脂粘度，實時顯示粘度控制曲線、粘度值，方便地實現樹脂粘度的設定、傳感器的標定、模糊控制器參數的改變，而且能通過控制界面隨時改變粘度的設定值。
  12. Methods of testing plastics - rheological properties - determination of viscosity number of methyl methacrylate polymers

    塑料試驗方法.第7部分:流變性能.試驗方法732f :異丁烯酸甲酯聚合物粘度值測定
  13. Abstract : the germinating capacities, fatty acid values and viscosities of wheat samples were analyzed by determining the viscosities, germinating capacities and fatty acid values, etc, which are the indices of quality deterioration, of 53 types of different wheat samples and the retrogradation degree and quality state of grains were showed through fatty acid value, germinating capacity, senes analysis and taste evaluation, however, wheat quality was evaluated by only viscosity which would cause greater error

    文摘:本研究通過測定53個不同品質小麥樣品的粘度值、發芽率和脂肪酸值等品質劣變指標，分析了發芽率、脂肪酸值和粘度之間的關系，並認為脂肪酸值、發芽率、感觀分析及品嘗評分結果都能較好地說明糧食的陳化程度和品質狀況，而粘度值用於評價小麥的品質則會產生較大的誤差。
  14. The results showed that the 11 measured cooking and eating quality properties and taste value have manium significance genetic difference ; among the cooking and eating quality properties, varietal variation coefficent of gel consistency, peak viscosity, break down, setback is relatively large ; every cooking quality property has a different correlation with eating quality property, initial pasting temperature, finial viscosity, consistency and setback have significant or maximum significant inverse correlation with taste value, while peak viscosity, break down has a postive correlation with taste value, amylose content and protein content are inversely related to taste value, but gel consistency are positively related to taste value another, the correlation among varietal cooking and eating quality properties is significant or maximum significant ; in the analysis of principal components, the cumulative percent of 4 selected principal components reached 90. 58 %, initial pasting temperature of large second principal components is small, but amylose content and protein content is high, finial viscosity, consistency are large

    結果表明，所測定的11項蒸煮食味品質特性及味度值在供試品種間均存在著極顯著的遺傳差異；在蒸煮食味品質特性中，膠稠度、最高粘度、下降粘度值、粘滯峰消減值的品種間變異系數較大；糊化開始溫度、最終粘度、回冷粘滯性恢復值、粘滯峰消減值與味度值呈顯著或極顯著的負相關，而最高粘度、下降粘度值與味度值呈極顯著的正相關，直鏈澱粉和蛋白質含量與味度值呈負相關，而膠稠度與味度值呈正相關；在主成分分析中，被入選的4個主成分的貢獻率達90 58 ，其中第二主成分大的品種，糊化開始溫度低，直鏈澱粉和蛋白質含量高，最終粘度和回冷粘滯性恢復值大。
  15. Plastics - determination of the viscosity of polymers in dilute solution using capillary viscometers - general principles

    塑料.用毛細粘度計測定稀釋溶液中聚合物的粘度值.一般原理
  16. Plastics - determination of the viscosity of polymers in dilute solution using capillary viscometers - poly vinyl chloride resins

    塑料.用毛細粘度計測定稀釋溶液中聚合物的粘度值.聚氯乙烯樹脂
  17. Plastics - polyamides - determination of viscosity number iso 307 : 2003 ; german version en iso 307 : 2003

    塑料.聚酰胺.粘度值的測定
  18. Plastics - cellulose acetate in dilute solution - determination of viscosity number and viscosity ratio

    塑料.稀溶液中的乙酸纖維素.粘度值和粘度率的測定
  19. Standard test method for determining logarithmic viscosity number of poly vinyl chloride in formulated compounds

    測定按配方製造的化合物中聚氯乙烯對數粘度值的標準試驗方法
  20. This machine can automaticaly dilute printing ink and glue to make a proper viscosity ualue maintainting constant viscosity of printing colors and composite glues, reducing waste rate

    該機能自動稀釋油墨膠水粘度值。印刷色彩復合膠水粘度，自始自終保持一致，減少了廢品率。
分享友人
分享到 Line

分享到臉書