粘性時間短 的英文怎麼說
中文拼音 [niánxìngshíjiānduǎn]
粘性時間短
英文
short tack time- 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
- 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
- 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
- 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
- 短 : Ⅰ形容詞（空間、時間兩端之間的距離小） short; brief Ⅱ動詞（缺少; 欠） lack; owe Ⅲ名詞1 （缺點） we...
- 時間 : time; hour; 北京時間十九點整19 hours beijing time; 上課時間school hours; 時間與空間 time and spac...
-
A lot of experiments have been done in the process of exploiture soft packaging li - ion battery about how to choice the rational arts and crafts. the content include : how to deal with the collector, add how much pvdf in the material, how long the material need to stirring and the right viscidity, how much condubtivity agent the electrode need, what theckness is best, choice different collectors, the degree of dryness of the electrode, theckness of pressed model, how much electrolyte will be added, placement how long after added the electrolyte, system of formation how to influnce the battery, in formation the battery need or not need preesure from outside, how to vacuumize and the optimize matching positive pole and negative pole. with these practice make sure the parameter of the positive pole should less than 90 m ; according to different vacuumize order the conduc - tivity agent in anode will be 5mass % and 9mass %, respectively, and in cathode the data is 2mass % ; every 100mah added to 0. 4 ml electrolyte ; before formation the battery should be placement 8 hours and the system of formation must be less than 0. 01c before the voltage reach to 3. 0v ; should press in outside when battery in formation ; to these batteries which capacity more than 350mah the vacuum time not excess 15s ; the optimize matching positive pole and negative pole between 2. 10 : 1 and 2. 15 : 1. finally make out the battery which cycling performance and security are all very well
液態軟包裝鋰離子電池的研究主要是對關鍵工藝進行了優化設計，具體包括:集流體的處理、 pvdf的加入量、漿料攪拌時間和粘度、導電劑的加入量、電極膜的厚度、不同集流體的選擇、電極膜的乾燥程度、壓型的厚度、電解液的加入量、注入電解液后靜置時間的長短、化成制度的影響、化成時電池所具有的壓力影響、抽真空的處理、正負極活性物質的匹配。最後確定出液態軟包裝鋰離子電池最佳工藝參數:正極膜的厚度小於90 m ;根據化成時不同抽真空順序，確定正極膜中的導電劑的加入量分別為5mass %和9mass % ;負極膜中導電劑的加入量為2mass % ;電解液的加入量為每100mah添加0 . 4ml ;化成前電池的靜置時間應當大於8h ;電池在3 . 0v之前採用小於0 . 01c的化成制度;在化成過程中應當施加一定的外部壓力;對於350mah的電池抽真空的延時不應大於15s ;而正負極活性物質的質量比應當在2 . 1 : 1 2 . 15 : 1之間。Regarding the lcm filling process as the newton fluid through fibrous reinforcements, the permeability of preform determines the saturating of resin in fiber, and has effects on the curing process and the quality of products. based on the darcy ' s law, the theoretical model of permeability measurement was established. and the influence of different testing methods and major process parameters such as fabric structure, fiber volume fraction, injection pressure, flow rate and resin viscosity on preform permeability were investigated in details
文中首先根據達西定律建立了滲透率測量的理論模型，深入研究了不同的測試方法及主要工藝參數（纖維織物織構、纖維體積含量、充模壓力、流動速度、樹脂粘度）對滲透特性的影響規律，發現多孔介質增強材料的滲透率主要取決于纖維織物的結構形式，預成型體孔隙分佈及其體積分數、壓實性對滲透率有較大的影響，提高充模壓力和流動速度可以縮短充模時間，在一定程度上可以提高滲透率。However, liquid drugs administered by nasal cavity and rectum have a low bioavailability due to staying a short time. the gel prepared with carbopol has strong bio - adhesion, can prolong contact between drug and mucosa. it may be used in nasal and rectal immunization
然而，鼻腔及直腸均為管腔通道，液體藥物停留時間較短，生物利用度低，用生物黏附劑卡泊波（ carbopol ）制備的凝膠，具有粘度高、生物粘附性好的特點，能延長藥物與粘膜的接觸時間。
分享友人