粘接裝置 的英文怎麼說

中文拼音 [niánjiēzhuāngzhì]
粘接裝置 英文
klebevorrichtung bonder
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 裝置 : 1 （機器設備的配件）installation; device; apparatus; equipment; arrangement; gear; appliance; rig...
  1. First, a simple discussion for the mechanism about electrostatic atomization of the liquids has been given ; then the paper theoretically analyzed waving course, liquid drop producing course, and the liquid drop diffusing course in electrostatics atomization process., gave an analysis about the methods about carrying charges to the liquid drop, and analyzed that liquid with high electrical conductivity can be carried charges and atomized by electric field, while the isolated liquid with low electrical conductivity can be charged fully with the soakage electrode and inducing charge methods. at last the paper designed and configured the experimental equipment, conducted the atomization experiment to the three liquid medium - kerosene, emulsifier and alcohol under the same environment, handled the experimental results, then summarized the relationship between liquid electrostatic atomization effect and liquid surface tension, electronic conductivity and viscosity, along with the influence of voltage to electrostatic atomization and so on, found out the liquid atomization rule in high voltage electrostatic field

    首先，對液體介質的靜電霧化機理作了初步的探討，理論上分析了液體霧化過程中射流區、波紋區、霧滴區和霧滴擴散區;然後對液體荷電方法進行了研究分析，對于高電導率的液體，場致荷電和接觸荷電可以使其霧化，而對于電導率較低的絕緣液體，需用浸潤電極荷電和感應荷電方法使其充分帶電;最後，根據前面的研究分析，設計和組裝試驗裝置，在同一環境下對煤油、乳化劑、酒精三種不同液體介質進行高壓靜電霧化試驗，並對試驗結果進行分析處理，總結出液體靜電霧化與液體表面張力、電導率和粘度的關系及電壓對液體靜電霧化的影響等，得出高壓靜電場中液體霧化的一般規律。
  2. You can fine - tune task links - and make sure you do n ' t gum up the clockwork - by using lag time and lead time

    使用「前置重疊時間」和「延隔時間」調整任務鏈接，並且確保那些鐘表裝置不會粘上油漆。
  3. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  4. A uniform mathematical formula has been established for the two devices consisting of brace and viscoelastic damper or viscous damper

    本文對粘彈性和粘滯阻尼器在與支撐連接后的阻尼裝置建立了統一的力學模型，並研究了支撐剛度對其性能參數的影響。
  5. Packaging materials and systems for medical devices which are to be sterilized - adhesive coated nonwoven materials of polyolefines for use in the manufacture of heat sealable pouches, reels and lids - requirements and test methods

    準備消毒的醫療裝置用的包裝材料和系統.用於生產熱密封袋，卷軸和合蓋的粘接劑包覆的非紡織的聚烯烴材料.要求和試驗方法
  6. The major influencing factors of felting quality are pre - heating temperature and glue depth, and the installation of the temperature raising set in the felting parts

    經分析確定了影響粘接質量的主要因素是加熱溫度與打膠深度，對粘接部分增加了預加熱裝置。
  7. Low viscous drag and high - speed capability : the low viscous drag of the magnetic fluid, and non - contacting seal configuration of the magnetic fluid feed through assure its extremely smooth operation and its high - speed capabilities

    低阻尼和高速旋轉能力：磁性流體極低的粘滯阻力和磁性流體進行給裝置無需接觸密封圈的結構，決定了它的穩定操作和高速轉動。
分享友人
分享到 Line

分享到臉書