粘液溶解的 的英文怎麼說

中文拼音 [niányèróngjiěde]
粘液溶解的 英文
mucolytic
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 液 : 名詞（液體） liquid; fluid; juice
  • 溶 : 動詞（溶化; 溶解） dissolve
  • 解 : 解動詞（解送） send under guard
  • 的 : 4次方是 The fourth power of 2 is direction
  • 溶解 : dissolve; dissolution; solution; lysis; solvus; resolution; decomposition; resolving; solving; fu...
  1. Both myxoviruses and lysosomes are equipped with enzymes which can degrade glycoproteins.

    粘液病毒和溶解體均裝配某些能分解糖蛋白的酶。
  2. The composite has excellent performance of water retaining, that the adsorbed water of 85 % is retained after being dried 10 days at the room temperature, and the adsorbed water of 45 % is retained after being dried 24 hours at 60 the factors influencing on water absorbency for the superabsorbent composite such as the kinds and concentration of starch, clay, crosslinker, initiator, the external salt solution and hydrolysis degree are investigated in this paper

    該超吸水性復合材料在室溫下乾燥10天後的保水率為85 ，在60 2條件下加熱24小時后的保水率為45 。本文較詳盡地探討了超吸水性復合材料的合成條件，並系統地研究了影響超吸水復合材料吸水倍率的各種因素。例如：粘土的種類及粘土的用量、澱粉的種類及澱粉的用量、交聯劑的用量、引發劑的用量、水解度（氫氧化鈉的用量） 、水解時間、外部鹽溶液的種類及濃度等條件。
  3. The subsidiary company, yongan fuhuaxian articles supply factory, can produce 191 serial unsaturated polyester resin which is a clear and heavy - bodied liquid. it is made by the method of the solvation of linear unsaturated polyester resin, which is condensated and polymerized after the esterification of biatomic acid and diatomic alcohol, into phenylethylene solvent, which is a crosslinking active monomer

    所屬子公司永安市福化纖用品廠生產的191系列不飽和聚脂樹脂，系由二元酸酐和二元醇及其縮合物經酯化反應，縮聚成線性不飽和聚酯樹脂，然後經具有交聯作用的活性單體溶劑苯乙烯所溶解而配製成的透明粘稠液體。
  4. Mps can be dissolved without problems in the water - phase of water - in - oil or oil - in - water emulsions, as well as in most common water based gel systems

    Mps （多磺酸粘多糖）不但能輕易地溶解於水包油的水相態或油包水的乳液態，而且能輕易地溶解于以水為基質的凝膠系統。
  5. You are correct about the - 40c miscibility problems. the oil has to have a low pour point in order to flow and still have sufficient viscosity for the compressor lubrication

    你談到油在40度的溶解性的問題是正確的。油不得不具有有一個很低的流動點（流（動）點：油或其他液體在規定條件下流動的最低溫度） ，還需要有足夠的粘度作為壓縮機的潤滑作用。
  6. Several fabrication methods, including nonwoven meshes / fiber bonding, solvent casting / particulate leaching, phase seperation / freeze drying, gas foaming and three - dimensional printing, which are used to prepare tissue engineered porous scaffolds from natural or synthetic biodegradable materials, are reviewed

    摘要綜述了以天然或合成生物降解材料為原料的組織工程多孔支架的幾種制備方法，包括無紡織物纖維粘結法、溶液澆鑄粒子洗出法、相分離凍干法、氣體成孔法和三維「印刷」等方法。
  7. It is found that, the sintering process of w - ni - fe - cu alloy was a typical liquid - phase process, which including particle rearrangement stage, dissolving - precipitation stage and solid - phase sintering stage. cu plays an important role in the particle rearrangement stage, while fe can promote the densification by forming ni - fe - w bonding - phase. ni can not only form the bonding - phase, but also enhance the diffusion between the w grains

    研究表明， w - ni - fe - cu合金的液相燒結緻密化經歷了顆粒重排、溶解-析出和固相燒結等三個階段， cu僅在顆粒重排階段起主導作用； fe主要在溶解-析出階段通過形成ni - fe - w三元粘結相來促進w合金的燒結緻密； ni不僅參與形成ni - fe - w三元粘結相，並且在w晶界上通過與w的互擴散促進了固相w晶粒的粘合。
分享友人
分享到 Line

分享到臉書