粘貼法線 的英文怎麼說

中文拼音 [niántiēfǎxiàn]
粘貼法線 英文
paste normal
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 貼 : Ⅰ動詞1 （粘貼） stick; paste; glue 2 （緊挨） nestle up to; snuggle up to 3 （貼補） subsidize; h...
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 粘貼 : paste; stick
  1. The technique training contains the content are many, for example : the wax pencil water color ' s modelling, cancels the line, the color ; the clay sculpture class rubs sticks the picture ; manual class paper folding, cutting out, glue, . . . therefore, the technique training both must fasten tightly each class the key point, and must have the whole situation in mind, application of local experience to the entire area ; both must focus on all personnel schoolmate, and must consider the individual result prominent or ability weak schoolmate, teaches students in accordance with their aptitude ; both must praise encourages, and must counsel specifically, helps them to solve in the technical difficulty

    技法訓練包含的內容較多，如：蠟筆水彩的造型、勾線、上色；泥塑課的揉搓粘畫；手工課的折紙、裁剪、粘貼， … …因此，技法訓練既要扣緊每節課的重點，又要胸有全局，點面結合；既要著眼于全班同學，又要照顧個別成績突出或能力較弱的同學，因材施教；既要表揚鼓勵，又要具體輔導，幫助他們解決技術上的困難。
  2. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  3. And the calculated results closely coincide with experimental results. furthermore, the paper, through applying the improved algorithm to the load - deflection curve and secondary load, also the calculated curves closely coincided with experimental results ( showed as chart 3. 17 - 3. 20 )

    本文還將改進的演算法運用於粘貼加固受彎構件的荷載?撓度曲線和二次受力問題的計算中，得出與試驗結果吻合較好的計算曲線（圖3 . 17 3 . 20 ） 。
  4. The early studies are mostly focused on the method of gluing piezoceramics on structural surfaces, which has some disadvantages such as difficulties to protect the ceramics and the connection wires, bad coupling with only one surface glued on the base materials, low signal - to - noise ratio etc. these problems can be solved using the embedded piezoceramics, and furthermore, the piezoceramics can be placed in the optimal positions, especially in the optimal deepness for the piezo - actuators, according to an optimization algorithm befor e they are embedded, so the actuator effects and sensor signals are thereby enhanced

    早期的研究主要集中在表面粘貼壓電片的結構，表面粘貼壓電片具有一些無法克服的缺點。本文著重進行利用埋入復合材料結構的壓電傳感器和壓電驅動器對其振動進行主動控制的相關理論和實驗研究，並介紹其相應結果。埋入型壓電材料的優點主要是能保護壓電傳感器和作動器及其連線、增強壓電材料和基體材料的耦合、優化埋入壓電陶瓷的深度和厚度可增強壓電傳感器的測量信號並提高信噪比等。
  5. 3. a method for the acquisition of 3d data was implemented by distributing reference points over the objects to be digitized and utilizing the techniques of feature extracting, epipolar rectification, feature matching, and the triangulation principle

    3 .通過在物體表面粘貼圓形特徵點的方法，綜合圖象特徵提取、極線校正、特徵匹配、光學三角法等技術，實現了三維數據的獲取。
分享友人
分享到 Line

分享到臉書