細砂輪 的英文怎麼說
中文拼音 [xìshālún]
細砂輪
英文
close grained wheel-
Take the cooling of grinding emery wheel as an example and in accordance with cold wind cooling machining system graph, the cooling method and requirements with sub - dried air were introduced in detail
依據冷風冷卻加工系統圖，以冷卻磨削砂輪為例，詳細地介紹了亞乾式空氣的冷卻方法及要求。On the other side, based on research on noncircular surface grinding features, this deissertation designs the data structure of simulation driver, then, applies interpolation theory to design the grinding motion simulation module and researches all sorts of cases on constructing the solid swept of grinding wheels in the process of noncircular surfaces grinding, finally, designs nc codes verification simulation module by using design model - based verification technique
在實體模擬技術方面，詳細研究了非圓曲面磨削加工的特徵並設計了對應的模擬驅動數據結構;應用插補原理設計了體現加工速度的運動過程模擬模塊;詳細研究了非圓曲面磨削加工中砂輪的相對和絕對運動掃掠實體的構造，並採用基於精確實體設計模型的驗證方法構建了數控代碼的模擬驗證模塊。This paper introduces an innovative design of m1050 centerless grinding machine which provides automation for feed mechanism, regulation & compensation of wheel & guide wheel and parts inspection in addition, the design principle is also described with a detailed illustration on structure design of the automatics above - mentioned
摘要介紹了m1050無心磨床自動進給、砂輪、導輪自動修正與補償裝置的改造設計及自動測試裝置的設計，闡述了設計原理，詳細介紹了裝置的結構設計。The palaeogeographic research indicate that the palaeogeographic outline of the study area recorded the evolution from a sedimentary basin in which the shallow - water carbonate platform sediments and deep - water terrigenous clastic submarine fan developed from southeast to northwest and northeast during the late triassic through a submarine sheet - like model composed of deep - water sandy turbidite and fine - grained turbidite during the early jurassic to a terrigenous clastic barrier coast during the middle and late jurassic and finally to the coal - bearing delta sediments during the late cretaceous
古地理分析表明，研究區晚三疊世古地理輪廓是一個從東南向西北和東北方向由淺水碳酸鹽臺地及深水陸層海底扇沉積共同發育的沉積盆地；早中侏羅世，演變成為一個由深水砂質濁積巖和細屑濁積巖組成的水下席狀體沉積；進入中晚侏羅世，其古地理表現為一個陸屑淺海有障壁海岸；到了晚白堊世，研究區表現為以含煤沉積為特徵的三角洲相沉積。Although reducer can avoid step sense and oscillation partly, the strap transmission will influence orientation precision ( it is key norm to the small metallographic sample cutting machine ), so plan to use step motor to drive the screw directly, the step motor at low velocity, which is not drived by the subdividing drive system, will have obvious oscillation and noise that would influence the cutting function, the usage life and sample structure
由於步進電機是通過皮帶輪減速來驅動絲杠，進而帶動砂輪片前進和後退，雖然減速能部分消除步進感和振動，但皮帶傳動會影響定位精度，定位精度對精密切割機十分關鍵的技術指標。採用步進電機直接驅動絲杠，未經細分驅動的步進電機在低速運行時，有明顯的步進感、振動和噪聲，從而對切割的性能、砂輪片的使用壽命、試樣的組織結構產生較大的影響。The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement
研究結果表明，增大砂輪軸向進給速度和減小工件轉速，採用粗粒度砂輪有利於提高磨削矽片的材料去除率，砂輪軸向進給速度對材料去除率的影響最為顯著；適當增大砂輪轉速，減小砂輪軸向進給速度，採用細粒度砂輪可以減小磨削表面粗糙度；在其它條件一定的情況下，砂輪速度超過一定值會導致材料去除率減小，主軸電機電流急劇增大，表面粗糙度變差；採用比# 2000粒度更細的砂輪磨削時，材料去除率減小，矽片表面粗糙度沒有明顯改善。In this paper compensation method of wheel sige deviation is discussed in detail
這里還詳細討論了砂輪尺寸誤差的補償方法。Features and use : it is used for abrading rubber 、 plastic or the same kind material like them. has the advantage of two grinding wheel working at the same time
特點及用途：用於磨製橡膠、塑料或類似的試片至一定的厚度供其他試驗設備進行試驗之用，具有精細兩種砂輪同時工作之優點。分享友人