終滲能力 的英文怎麼說

中文拼音 [zhōngshènnéng]
終滲能力 英文
final infiltration capacity
  • : Ⅰ名詞1 (最後; 末了) end; ending; finish 2 (指人死) death; end 3 (姓氏) a surname Ⅱ形容詞(...
  • : 動詞(液體慢慢地透過或漏出) ooze; seep
  • : 能名詞(姓氏) a surname
  • : Ⅰ名1 (力量; 能力) power; strength; ability; capacity 2 [物理學] (改變物體運動狀態的作用) forc...
  • 能力 : ability; capacity; capability
  1. If untreated, the blood and the exudation accumulated over the macular region will damage the photoreceptor cells over there and eventually cause irreversible visual loss

    若不妥善處理,血液和出物會于黃斑區積聚,破壞區內的感光細胞,最導致不彌補的視受損。
  2. During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied

    在溫度場的模擬中,模擬結果表明,保壓時間是影響製件成形質量的關鍵因素之一,擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大,需進行參數之間的協調,只有當變形區內部始維持準固態時,才實現穩定的液-固擠壓成形過程;在變形場的模擬中,根據液態浸擠壓的成形特徵,選用了雙曲正弦剛-粘塑性有限元計算模型,研究了變形過程中應應變場的變化規律,研究了模角對變形和金屬流動的影響及變形的變化過程和其影響因素。
  3. Gin is the abbreviation for grouting intensity number. it is showed by the product of the final grouting pressure p ( unit : mpa ) on the grouting section and the grouting volume v ( unit : l / m ) on every one meter of the grouting section, which means the energy consumed on every one meter of grouting section. according to gin method, if during the grouting construction, same energy is consumed on every grouting section, i. e. gin keeps to be a constant, an approximately uniform impervious curtain can be obtained

    Gin ( groutingintensitynumber )即灌漿強度值,它用灌漿孔段上最的灌漿壓p ( mpa )和單位灌漿段長度漿液灌注量v ( l / m )的乘積表示,其含義為單位灌漿段上消耗的量, gin法灌漿認為在灌漿施工中,保持各灌漿孔段上消耗一致的量,即保持gin為常數,便可形成一道大致均勻的防帷幕。
  4. Use the principle of material complex, carboxylic styrene - butadiene rubber latex added to the ordinary mortar forms pmm which takes the place of the conventional mortar as the surface coated. it can improve the cracking - proof feature, permeability, flexibility, as well as the compatibility with formwork concrete, to protect the formwork from corrosion and finally to enhance the durability of formwork concrete

    利用材料復合的原理在普通砂漿中摻入丁苯膠乳形成聚合物改性水泥砂漿代替傳統的普通水泥砂漿作為模網混凝土的表面保護層,以改善面層砂漿的抗裂性、抗性、柔韌性,提高其與模網混凝土的協調變形,從而保護內部鋼模網不受銹蝕並最提高模網混凝土的耐久性。
  5. The action that weak cold air penetrated into the tropical cyclone made the low pressure become vortex potential instability, and finally turned into kinetic energy. the results were that the center pressure of low became lower, the wind velocity around the cyclone was stronger and the precipitation became more

    冷空氣在中低層的透主要使大氣斜壓作用加強,使不穩定量的積聚並最釋放;還造成臺風渦旋位勢不穩定,使熱帶氣旋中心氣壓降低,周圍風加大,因而產生更大的降水。
分享友人