終端電阻器 的英文怎麼說
中文拼音 [zhōngduāndiànzǔqì]
終端電阻器
英文
final resistor- 終 : Ⅰ名詞1 (最後; 末了) end; ending; finish 2 (指人死) death; end 3 (姓氏) a surname Ⅱ形容詞(...
- 端 : Ⅰ名詞1 (東西的頭) end; extremity 2 (事情的開頭) beginning 3 (門類; 方面) item; point 4 (原...
- 電 : Ⅰ名詞1 (有電荷存在和電荷變化的現象) electricity 2 (電報) telegram; cable Ⅱ動詞1 (觸電) give...
- 阻 : 動詞(阻擋; 阻礙) block; hinder; impede; obstruct
- 器 : 名詞1. (器具) implement; utensil; ware 2. (器官) organ 3. (度量; 才能) capacity; talent 4. (姓氏) a surname
- 終端 : terminal; terminus; terminator; tag end; end; termination; trailing end; end point; terminating終...
- 電阻 : (物質阻礙電流通過的性質) resistance; electric resistance (電路中兩點間在一定壓力下決定電流強度...
-
Termination resistors should be placed only at the extreme ends of the data line, and no more than two terminations should be placed in any system that does not use repeaters
終端電阻只能安裝在數據線的最末端,在沒有使用中繼器的系統中,不得使用兩個以上的終端電阻。For bus system installation, the focus is put on cable selection principle, installation process and antinoise measure ; for security protection equipment installation, the intrinsic safety concept, installation method equipment selection and installation under two electric power supply modes ( entity concept and fisco model ) and the bus system protection against surge voltage are illustrated ; for network component installation, the selecting, installing and integrating methods of general purpose terminators, repeaters, link equipment, bus power supply and impedance module are described
在總線電纜的安裝方面,著重討論了電纜的選型原則、安裝方法和抗噪防擾措施;在安全保護設備安裝方面,介紹了總線系統中本質安全的概念、安裝方法、兩種供電方式(實體概念和fisco模型)下設備的選擇與安裝以及總線系統浪涌電壓的保護和設備安裝方法;在網路元件的安裝方面,主要列舉了通用終端器、中繼器、鏈路設備、總線電源及其阻抗模塊等的選擇、安裝和集成方法,為總線系統的安裝提供了可以借鑒的實用經驗。The simulation results indicate, deep - trench junction termination with certain width, depth and filling with isolated dielectric can increase the avalanche breakdown voltage of devices to above 95 % of the ideal value
結果表明:具有一定寬度、深度且填充絕緣介質的深阱結終端結構,阻止了結的橫向擴展,並能將器件的雪崩擊穿電壓提高到理想值的95以上。Harmonized blank detail specification for lead screw actuated non - wirewound preset potentiometers - square form, container sealed, actuating device insulated from resistive element, slipping clutch at each end of travel, rigid terminations - assessment level s
導螺桿傳動非線繞預調電位器協調空白詳細規范.正方形的容器密閉的與電阻元件絕緣的驅動裝置每個行程終止的滑動離合器剛性終端.評定級別sThe conventional connection circuit as the figure shows for two - wired transmitter : handhold terminal palm computer and external communication interface or mainframe communication circuit cannot directly bridges in the ends of power source. but may either meet on field ends a and b or meet on the ends of load resistance b and c. in the above - mentioned case, the circuit are supplied by power source
對兩線制變送器來說,傳統的連接電路如圖所示:手持終端掌上電腦和外接通訊介面或主機通訊電路不能直接跨接在電源兩端,但既可接于現場兩端a , b上,也可接在負載電阻兩端b , c ,兩種情況下,電路都要通過電源來供電, hart規范允許負載電阻為2301100 。Recommendations for preferred diameters of wire terminations of capacitors and resistors
電容器和電阻器終端線的優選直徑的推薦標準分享友人