結構參數 的英文怎麼說

中文拼音 [jiēgòushēnshǔ]
結構參數 英文
design value; structural parameter
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 參 : 參構詞成分。
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 結構 : 1 （各組成部分的搭配形式） structure; composition; construction; formation; constitution; fabric;...
  1. The best optimum mathematical model is constituted. scalar factor of structural parameter on loop rectangular negative pressure and adsorption slide is calculated. structural parameter, air gas source pressure carrying capacity and thickness of air cell are made sure by hydrodynamics and the theory of gas lubrication

    詳細論述了導軌副的設計過程，運用數學上的拉格朗日條件極值求解法，建立最優化數學模型，求出環矩形負壓吸附導軌的結構參數的比例情況，並運用流體力學和氣體潤滑理論確定了環矩形負壓吸附導軌的結構參數、氣源氣壓、承載能力和氣膜厚度的確定性結論。
  2. Piezoelectric - stack can give more output displacement and pressure and have more rate of conversion and more stability than bimorph type. it has been used to all kinds of driving places. design of displacement amplification we design displacement amplification because of the little displacement output of the piezo - stack. this paper analyses the disadvantage and advantage of all sorts of amplification, and proposes a new type of displacement amplification based on

    鑒于壓電疊堆輸出位移小的特點，引入柔性鉸鏈位移放大機構，分析了各種放大機構的優缺點並結合實際問題，設計出基於三角形放大原理的橢圓形放大機構，利用有限元分析軟體ansys對放大機構的主要結構參數進行了分析，得出影響放大機構放大倍數的規律。
  3. Furthermore, the maximum and minimum cleaning angle and sliding angle of seeds in the scoop were determined, the angle of clapboards hatch and the thickness of scoop top were derived

    建立了持種空間及在排種平面投影的理論計算公式，分析了持種空間隨分種勺結構參數和工作位置的變化。
  4. We acquired the system ' s dynamic response when the satellite attitude was adjusted and the mode of the antenna. then modal analysis and dynamic analysis have been done to the satellite - antenna system by using the finite element analysis ( fea ) software of ansys. through the analysis we got the system ' s connatural characteristic, the amplitude - frequency characteristic of harmonic response, the power spectrum density of random vibration response, the maximal amplitude and resuming time of impact response

    其次藉助ansys有限元分析軟體，對系統進行了模態分析和動力學響應分析，獲得了不同天線結構參數下的衛星?天線系統的固有特性，簡諧響應的幅頻特性，隨機振動響應的功率譜密度，以及沖擊響應的最大幅值和恢復時間等。
  5. Across the rigid - flexible coupling dynamic analysis, we acquired the coupled effects between the three - dimensional attitude motion of the satellite and the flexible vibration of the antenna ' s supporting beam, and got the dynamic behaviors of the system. and we found the change pattern of the antenna ' s structure parameters, which decide the system ' s connatural characteristic and its dynamic response

    通過對衛星?天線形成的剛柔耦合系統進行動力學分析，獲得了衛星的剛體運動與天線的彈性振動之間的耦合影響規律及其真實的動力學行為，得到了天線結構參數對衛星?天線系統的固有特性及其動力學響應的影響規律，為衛星姿態控制和天線結構優化設計奠定了基礎。
  6. We can also detrude the parameter of trace and pcb when we regulate the settled coupling request. we can use the software to instruct the design

    也可以根據固定的對端接敏感器件的走線耦合要求或標準推導出相應的走線和pcb的物理結構參數，以此來指導設計。
  7. By the statistic analysis of the structural parameters of 419 fastback saloon cars in accordance with engine emission volume, the technological mainstream, average and highest levels of fastback saloon cars were proposed in this paper

    摘要對全球419個溜背型轎車的結構參數按發動機排量進行了統計分析，指出了當代溜背型轎車的技術主流及其達到的平均水平和最高水平。
  8. Through explaining the low - fluidity oil - deposit development structure in zaoyuan oil field, analyzing its reservoir structure and the strong flooding level hole design parameters, meanwhile adopting new techniques such as pouring water by phase control at the spot, weak point and strong plane, and so on to manage comprehensively and develop round, we have reduced the natural decrease and increased the exploitable reserves and caused the comprehensive development level of this field to rise from class 3 to class 1

    摘要對棗園油田低流度油藏開展構造精細解釋、相控儲層結構分析和強水淹層孔隙結構參數研究，同時在現場採用相控注水、點弱面強、投球調剖和注水吞吐等開發技術進行綜合治理和滾動勘探開發並舉，實現減緩自然遞減和增加可采儲量的目的，使該油田綜合開發水平由3類上升到1類。
  9. Lastly, pressing stress is related with enter angle, structural parameter, the progression and physical character of the poweder. the experiment verified tube roll mill " s grinding effect prior vertical mill and roller

    通過對筒輥磨層壓應力的分析可知：筒輥磨層壓應力與拉入角，結構參數，粉體級配物理性質有關。
  10. The rheological equations, derived from n - s equation in hydromechanics employing the newton fluid model and the bingham plastic model, demonstrate that damping force can be controlled by changing the magnetic field in the gaps. 4

    流變學方程表明：改變阻尼通道的磁場強度可以控制磁流變阻尼器的阻尼力，從理論上分析了磁路參數和阻尼通道的結構參數對磁流變阻尼器阻尼力的影響。
  11. Base on the optimize of structure parameter 、 examine of structure interference 、 research of machining technics and so on. manufacture the hyperboloid clutch with rollers, and it satisfy with the request of function and experimentation

    通過對雙曲面滾柱加載器的結構參數選擇、結構干涉檢測、加工工藝的研究，研製出了能夠滿足功能要求及實驗條件的雙曲面滾柱加載器。
  12. The experimental study on compositional parameters of the annular multinozzle jet pump

    環形多噴嘴射流泵結構參數的實驗研究
  13. Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer

    超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。
  14. 5 ) the 3 - d geometry and finite element model of the assembly of the optimized obturator of the breech mechanism is set up in terms of the optimized structural parameters. quasi - static and dynamic finite element analysis of stiffness, strength and obturating performance of the optimized obturator of the breech me chanism is performed

    利用優化后的結構參數建立了優化后炮閂閉氣結構的裝配體三維幾何實體模型和有限元模型，對優化后的炮閂閉氣結構剛強度和閉氣性能進行了準靜態及動態多體接觸彈塑性有限元分析。
  15. Bias voltage, which are related to the superlattice structural paraments, the doped densities and the applied bias voltage. we have also investigated the characteristics of superlattice under hydrostatic pressure by simulations

    超晶格的負微分電導區還導致出現固定偏壓下隨時間變化的電流自維持振蕩，振蕩產生的條件依賴于其結構參數，摻雜濃度和外加偏壓的大小。
  16. The structure and operating principle of an air - charged split - type adjustable shock absorber was described, e non - linear parameterized mathematical model of this shock absorber ' s damping characteristics was established according to fluid mechanics theory and the main structural affection factors to shock absorber ' s damping performance, such as the diameter of piston valve orifice, the diameter of adjustable orifice, the initial volume of gas chamber, the diameter of piston rod, the inner diameter of oil pipe and so on, were analyzed by simulations

    摘要通過分析一種分體式充氣可調阻尼減振器的結構和工作原理，運用流體力學理論，建立了該減振器阻尼特性的非線性參數化模型，模擬分析了活塞阻尼閥孔徑、阻尼調節孔徑、氣室初始體積、活塞桿直徑、油管內徑等主要結構參數對減振器阻尼性能的影響，通過試驗測試，得到了減振器樣件的阻尼特性及其可調范圍。
  17. Taking the contact stress, bend stress stiffness and temperature stress as the condition, taking the weight of the kiln tyre as optimization aim function, the redia and the width of the tyre are optimized general optimize methods just consider the affecting of the parameters to aim function, but in fact, structural parameters ( such as structure dimension, interval and so on ), physics and dynamics ( damp factor, conduct factor, friction factor material ' s elastic module strength limits and so on ), which would be changed after used. the difference are called discrepancy robust design ' s basic concept is : all design parameters " discrepancy will affect the aim funct ion and arouse the quality target discrepancy

    一般的優化方法，僅僅考慮了參數對其目標函數的影響，而實際情況下有些參數是變化的，產品的結構參數（如幾何尺寸、間隙等） 、物理和力學參數如阻尼系數、傳導系數、磨擦系數、材料的彈性模量和強度極限等的設計值與製造后和使用中的實際值會有差異，這種差異稱為設計變量和噪聲因素的變差。
  18. Based on this model, the effects of geometric and structural parameters, such as injection pressure, rear pressure, length - diameter ratio, inlet round angle - radius ratio and non - axis symmetry of nozzle, on the distribution of the cavitation inside the nozzle are analyzed

    基於這一模型進一步分析了噴射壓力、背壓和噴孔長徑比、噴孔入口圓角比、非軸對稱噴孔等幾何結構參數對噴孔內空穴分佈的影響。
  19. Study of stereometric parameters of optic nerve head of normal eyes using heidelberg retina tomography

    視網膜斷層掃描儀對正常人群視乳頭形態結構參數的測定
  20. Genetic optimization of stope structure parameters

    采場結構參數的遺傳優化
分享友人
分享到 Line

分享到臉書