絕對編程 的英文怎麼說

中文拼音 [juéduìbiānchéng]
絕對編程 英文
absolute prograrnming
  • 絕 : Ⅰ動詞（斷絕） cut off; sever Ⅱ形容詞1 （完全沒有了; 窮盡; 凈盡） exhausted; used up; finished 2 ...
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  • 編 : Ⅰ動詞1 （編織） weave; plait; braid 2 （組織; 排列） make a list; arrange in a list; organize; gr...
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 絕對 : absolute
  • 編程 : c programming
  1. In the program, the effect of lamination placement, construction interval, elastic modulus change, thermal insulation change, surrounding temperature change, concrete creep and autogenous volume change on thermal stress are considered. and such temperature control measurement as water pipe cooling, heat preservation of the dam surface, the pouring temperature control, the overflow across the dam top during flood season can also be simulated by numerical method

    該程序在編制過程中考慮了混凝土分層澆築、施工間歇、彈模變化、絕熱溫升過程、環境溫度的變化、混凝土徐變、自生體積變形等因素對壩體溫度場及溫度應力場的影響，同時也考慮了水管冷卻、壩體表面保溫、控制澆築溫度、施工汛期壩頂面過水等各種溫控措施的數值模擬。
  2. In this paper, the drive theory of the large ratio friction transmission is studied ; a new type elliptical cam wave generator is designed ; the large ratio friction transmission prototype is designed and manufactured ; based on the ansys finite element method software, structure of the elliptical cam is analyzed ; precision index of the manufactured large ratio friction transmission prototype, such as transmission accuracy, least step, stability of the least step, load capacity is measured by the absolute rotary encoder. by analyzing the measurement data and research content, it is think that the new elliptical cam wave generator could overcome a good many problems brought by processing errors, facilitate size precision adjustments, input moment can be achieved in the form of a pure force couple importing ; through this study, " the large ratio friction transmission prototype " could apply in practical engineering basically

    本文研究了大速比摩擦傳動的傳動理論;設計了新型橢圓凸輪波發生器，設計製作了大速比摩擦傳動樣機;用軟體ansys對所設計的橢圓凸輪結構進行了有限元分析;用19位絕對式編碼器測試了大速比摩擦傳動機構的傳動精度、最小步距、最小步距的穩定性以及帶負載能力等各項精度指標;對測量數據和研究內容進行了歸納和整理，認為新型橢圓凸輪波發生器克服了加工誤差帶來的諸多問題，新型橢圓凸輪波發生器可以進行尺寸精度調整，能夠達到輸入力矩以純力偶的形式輸入;通過本項研究，基本可以使「大速比摩擦傳動機構」在工程中得以應用。
  3. The distributed plc system of the floodgate ' s opening measuring presented by the paper has many advantages such as high reliable operation, high measuring precision, having the network communication function, convenient installation and correction, etc. this thesis further studies the key device for the floodgate ' s opening measuring, the rotary encoder, selects the absolute rotary encoder adopting the binary cyclic code, studies the method for transforming the cyclic code to the binary data and according to the transforming formula designs the ladder diagram program

    本論文研製的分散式plc閘門開度測量系統具有工作可靠、測量精度高、具有聯網通信功能、安裝和校正方便等特點。本論文深入研究了閘門開度檢測的關鍵器件? ?旋轉編碼器，選用了採用二進制循環碼編碼的絕對式旋轉編碼器，研究了將二進制循環碼轉換為二進制數的方法，根據轉換公式設計了plc的梯形圖轉換程序。
  4. We write the program which used for fighting errors in absolute positioning. we also write the program which used for linear combinating in absolute positioning. from analyzing for the measurement of outer, we can conclude that we can use m estimation to estimate parameter in gps absolute positioning. lt has application value. using it, we can obstain the stable positioning result and remove the outer. in this paper, we calculate the data which from the baseline space of the gps calibration space. we also draw some conclusion using broadcast ephemeredes and smoothing pseudoranges. the positionging precision is in 1 - 2 meter

    編制了gps絕對定位中抗差估計程序和應用線性組合進行單點定位的程序。通過對粗差量級的分析，得出在gps觀測量存在粗差時， m估計是有其應用價值的，它使定位結果較為穩定，減弱和剔除了粗差的影響。應用線性組合程序對gps綜合檢定場數據基線網點進行計算，得出用廣播星歷和平滑后的偽距可以給出較好的結果，點位精度在1 ? 2米。
  5. This can fully consider the effect of the structure of transmission line and the selection of lighting parameter etc. by calculating and analyzing various of factor that affect the lightning tripping probability of 500kv double circuit transmission line, we can draw the conclusions : the result by intersecting method is more accord with the practicality circumstance than by existing standard methods, using unbalance high insulation and reverse sequence of wire can reduce the contemporary outage rate of double circuit line, reducing the footing resistance is one of the most efficiency method to reduce the back stroking rate of double circuit transmission line, the double back stroking rate and the single back stroking rate will fall by three ground wire, when the footing resistance is 10 ohm, the back stroking rate by three ground wire is 83 percent of by two ground wire

    在分析輸電線路繞擊耐雷性能時，對線路的雷電屏蔽問題進行了分析，提出對擊距法進行改進，充分考慮了風速的影響因素，編寫了具有工程實用價值的計算線路繞擊耐雷水平的程序，此方法可以充分考慮線路結構和雷電參數等對繞擊率的影響。通過對影響500kv同桿雙回線路雷擊跳閘率的各種因素進行了計算和分析，得到以下結論：採用相交法的計算結果比定義法更符合實際運行情況。採用不平衡高絕緣方式和導線逆相序排列可以大大降低雙回同時跳閘率。
  6. Conventional iec three ratio method and new iec ratio criterion are reduced according to the method of decision table in rough set theory respectively, simplified diagnosis rules are proposed. besides being identical with original iec method, the codes of conventional iec three ratio method are increased and bounds of new iec ratio criterion are augment by using this method, codes imperfectness of conventional iec three ratio method and code name absence of new iec ratio criterion are improved to some extent, scarcity of codes in conventional iec three ratio method is offseted, absolutization of sort and boundary in new iec ratio criterion is overcomed. this is important in practice for its flexibility and enhanced error tolerances

    應用粗糙集理論中的決策表化簡的方法分別對常規iec三比值診斷表和iec新導則診斷表進行了化簡，得到了簡化的診斷規則，它們不但具有與常規iec三比值法和iec新導則完全相同的診斷分類能力，而且擴充了常規iec三比值表的編碼范圍和iec新導則的診斷范圍，在一定程度上改善了常規iec三比值表編碼缺損和iec新導則無對應代號的問題，彌補了常規iec三比值法編碼的不足，克服了iec新導則分類及邊界的絕對化，使得iec診斷法在實際診斷中更具靈活性、實用性和容錯性，提高了故障診斷能力。
  7. The rest mutations in pp38 and pp24 are at random. sequence analysis also shows the first 195 nuclear acids of pp38 and pp24 are the same except for the 81 site ( g / c ), but this mutation does not cause the change of amino acid. we regard this as a genetic marker connecting with geography in the evolution of mdv but not related to isolated time and pathotype of different strain of mdv i

    對pp24基因和pp38基因進行同源性比較分析的結果表明，絕大多數毒株二者的前195個核苷酸完全一致，不同毒株間的第81位核苷酸的差異（ g / c ）並不引起編碼的氨基酸變化，僅僅與地域分佈有關，這很可能是mdv在長期病毒衍化過程中形成的地域性遺傳標志，而與病毒的分離年代及mdv的致病型等因素無關。
  8. Then, the thesis presents a schema based two - level associated model, which dramatically reduces the number of the candidate subscriptions. in addition, an incremental subscription matching algorithm is proposed to efficiently matching events for millions subscriptions. furthermore, since indexing is very important to the system, the indexing scheme for xml data is defined based on the containment relationship, which can be more efficient to deal with relative paths than previous methods

    另外，由於在意向匹配過程中涉及大量索引問題，為此針對先前研究在處理基於相對路徑的意向表示上存在的問題，本文提出了一種基於相容關系的索引模式，利用系統抽象數據拓撲結構進行相對路徑到絕對路徑的轉換，通過基於相容關系的數字方式編碼，能夠快速確定對應結點的依賴關系，同時提出了新的路徑轉換演算法，將時間復雜度由過去的平方時間變為線性。
  9. Fbg - based strain sensor has many virtues such as unerodibility, absolute code of wavelength, ability for anti - jamming, simple structure and easy execution, etc. so it can replace the traditional mechanical and electrical strain sensor in civil engineering, and has prosperous outlook in the application

    光纖光柵應變傳感器具有耐腐蝕、波長絕對編碼、抗干擾能力強、結構簡單、實施方便等特點，在土木工程方面可取代傳統機械電子式應變傳感器，具有很好的應用前景。
  10. The paper emphasizly researches response functions of absolute radiometers, and the method of variational angle measure is corrected. the paper analyzes the function of an angle of incidence and the area in which absolute radiometers absorb the solar irradiance under considering the characteristic and principle of absolute radiometers. the function of absolute radiometers temperature raise and time is discussed, and the curve of the function is drawed by computer

    在結合絕對輻射計的結構特點和工作原理的基礎上，分析和討論了絕對輻射計接收光輻射的等效面積隨太陽光線入射角變化的函數關系式，在此函數關系式的基礎上，分析和討論了絕對輻射計接收太陽光輻射后，其溫度的升高量隨時間變化的函數關系式，並且用計算機編程畫出了絕對輻射計的溫度升高隨時間變化的曲線關系圖。
  11. Combining the strain mode curve data and element stiffness updating method, this paper present a method to identify the absolute damage extent. at last, the methods of location and damage extent identification have been integrated to a damage identification software which will make the identification conveniently. the studies in this article are as follow : 1

    本文對應變模態曲線尖峰的分析，提出來了識別相對損傷程度的方法，並結合單元剛度修正法提出了結構絕對損傷程度的識別方法，並將這種方法集成於自編的識別軟體中，界面簡潔，操作簡單，便於工程應用。
分享友人
分享到 Line

分享到臉書