絕熱分解溫度 的英文怎麼說

中文拼音 [juérèfēnjiěwēndù]
絕熱分解溫度 英文
adiabatic decomposition temperature
  • 絕 : Ⅰ動詞（斷絕） cut off; sever Ⅱ形容詞1 （完全沒有了; 窮盡; 凈盡） exhausted; used up; finished 2 ...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 解 : 解動詞（解送） send under guard
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 溫度 : [物理學] temperature
  1. Adiabatic decomposition temperature

    絕熱分解溫度
  2. The finite element method ( fe '. i ) is adopted to analyze the effects of the numbers of coil turns, current intensity and current frequency upon the rate of joule heat generation in details. the thermo - radiation analytical countermeasures of various types are adopted to carry out the numerical analysis of the effects of the crucible with different shapes and sizes and the blind holes with different depths opened in the tops of crucibles as well as coil positions upon the thermal field distribution whereby solving the main problem of field the thermo - field design of the induction - heating sic crystal growth system. a new combination idea of the thermo - field design obtained by means of the united design of the thermo - insulator and blind holes has been presented

    採用有限元分析方法對線圈匝數、電流強度、電流頻率等對焦耳熱產生速率的影響進行了詳細的分析討論；採用不同的熱輻射分析策略，對不同坩堝形狀、坩堝頂部開設不同深度的盲孔以及線圈的位置等對熱場分佈的影響進行了數值分析，解決了感應加熱碳化硅晶體生長系統熱場設計的主要問題，提出了通過絕熱層與盲孔的聯合設計獲得所需熱場設計的思路，給出了根據軸向溫度梯度的波動對線圈位置實行動態調節以控制熱場的理論依據。
  3. Insulating and sheathing materials of electric and optical cables - common test methods - part 4 - 2 : methods specific to polyethylene and polypropylene compounds - tensile strength and elongation at break after conditioning at elevated temperature - wrapping test after conditioning at elevated temperature - wrapping test after thermal ageing in air - measurement of mass increase - long - term stability test - test method for copper - catalyzed oxidative degradation

    電纜和光纜的絕緣和護套材料.通用試驗方法.第4 - 2部分:聚乙烯和聚丙烯化合物專用方法.高溫處理后抗拉強度和斷裂伸長度.高溫處理后的卷繞試驗.在空氣中熱老化后的卷繞試驗.質量增加的測量.長期穩定性試驗.催化銅氧化降解的試驗方法
  4. When the difference method is used to solve temperature problem, the error of adiabatic temperature rise of concrete is often caused by a difference step that is too big, at the same time computation workload increases greatly because of a difference step that is too small. based on the basic characteristics of the difference method, this paper introduced one kind of correcting method, which can assure solution precision but does n ' t increase the calculating workload

    針對差分法進行不穩定溫度場求解時，差分步長過大會造成絕熱溫升計算誤差加大，差分步長過小又會引起計算量成倍增長的問題，根據差分法求解的基本特點，提出了一種誤差修正方法，在計算量得到成倍提高的同時，保證了求解精度，較好的解決了這一問題。
分享友人
分享到 Line

分享到臉書