給水節熱器 的英文怎麼說

中文拼音 [gěishuǐjiérèqì]
給水節熱器 英文
feed-water economiser
  • 給 : 給Ⅰ動詞1 （送對方某物; 使對方得到） give; grant 2 （用在動詞后 表示交與 付出） pass; pay 3 （叫; ...
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 節 : 節構詞成分。
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 給水 : [機械工程] feedwater; water supply給水泵 feed pump; 給水量 confluent; 給水能力 capacity of water ...
  1. The afterheat, which is collected by recovery devices, in winter can be used as the low level thermal source of heat pump, and in summer can preheat feed water, thus equivalent an economizer. because energy flows in the system so reasonably that energy is used to the most, therefore, its energy conservation effect is significant, and the operating expenditure declines consequently. the sewage can be reused after due treatment, thua it has a certain social and ecological benefit, too

    本研究中選用分離式熱管裝置提供洗浴用水，利用水源熱泵裝置，一機兩用，進行空間供熱和製冷，並通過余熱回收器對系統內的余熱進行回收，冬季可作為水源熱泵的低位熱源，夏季可對鍋爐給水進行預熱，起到「省煤器」的作用。這樣實現系統內的能量合理流動，從而達到節能的目的，同時洗浴污水經適當的處理后可以回用，因而還具有一定的社會和生態效益。
  2. By adding high pressure water cleaning, hot water washing and optimization of bubble point test and filter core assemble process, the energy was saved, the consumption was reduced, the cleaning effiencency and quality was improved, the lifetime of filter was prolonged, the safety hidden danger of the process in pet production was removed

    摘要闡述了通過增加一道高壓水清洗、熱水洗以及對泡點試驗和過濾芯組裝等過程的優化，達到節能降耗，提高清洗效率，延長了過濾器使用周期，消除了此工序給聚酯生產帶來的安全隱患。
  3. On the other hand, in the new system the heater is set up directly in front of the accelerating tube so that stable cooling water can be supplied, because temperature can be roughly uniform as the lowest portions of the unstable temperature through heating

    ?來冷卻冷卻水溫度測定熱交換器冷水量三方弁調節。當社加速管直前設不安定溫度谷間加熱安定冷卻水供給可能。
  4. The mathematical and physical dynamic models are given based on the adsorbent theory of porous medium. its running and parameters affecting its performance are numerically studied and the method that control the water content in the absorbent bed is recommended. the improvement on system configuration to recover heat is discussed and the operation scheme is given

    利用多孔介質吸附模型和平衡吸附壓力的概念建立了該系統工作過程的物理數學模型，數值模擬的方法模擬了其工作過程和影響因素，提出了控制吸附床含濕量的方案，驗證了改進流程回收能量的可行性並給出了操作方案，提出並分析了用熱電製冷器回收水蒸氣潛熱節約電能的方法。
分享友人
分享到 Line

分享到臉書