統計允差 的英文怎麼說

中文拼音 [tǒngjìyǔnchā]
統計允差 英文
statistical tolerance
  • 統 : Ⅰ名詞1 （事物間連續的關系） interconnected system 2 （衣服等的筒狀部分） any tube shaped part of ...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 允 : Ⅰ動詞（允許） permit; allow; consent Ⅱ形容詞（公平; 適當） fair; just Ⅲ名詞（姓氏） a surname
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 統計 : 1 （對有關數據的搜集、整理、計算和分析） statistics; census; numerical statement; vital statistic...
  1. An isolated point " s statistic excluding method is proposed in this paper to eliminate crassitude error in clouding data, which include plenty of oddity data. the method based on the distance between two neighbour points can eliminate the data beyond normal distribution. a error limitation of angle and chordal highness method is used to filtrate clouding point

    針對大量含奇異點的數據點雲，本文提出了剔除粗大誤差的孤立點統計排異法，該方法根據對相鄰點距離的統計，剔除在正態分佈以外的點；對大量數據的精減，利用角度和弦高的最大允許偏差法進行點雲精減。
  2. Examinations of steady status and analysis of dynamic experiments have been conducted on band - tube evaporator and parallel - flow condenser using r134a refrigerant. the steady examination show that the model error was under the allowable error, the inlet mass and enthalpy disturb experiments indicate that the subsection model, be good at reflecting the change of parameters of the heat exchanger, accord with the basic principle of thermodynamics theory and the actual work status. hence, the subsection simulation model research has important benefits both on theory and engineering application

    在進行模擬試驗時，以使用r134a作製冷劑的管帶式蒸發器和平行流式冷凝器為對象，完成了穩態模擬計算、試驗和動態模擬分析，穩態計算結果和試驗數據對比表明，其誤差在允許范圍內；進口質量和焓值的擾動試驗結果表明：本文所建的區段式換熱器模擬模型，能很好的反映換熱器性能參數的動態變化，與系統熱動力學理論和冷凝器、蒸發器的實際工作過程基本一致。
  3. It has shown by the uncertainty of the data of fatigue experimentation and the size deviation of machine accessory and structure component and the original defect of materials that all of the stress and intensity and the factors that affect them are stochastic variables, so we should deal with the problem of fatigue by the method of probability and statistics to making the engineering life deduced by fatigue intensity to be the reliable life under a certain probability

    疲勞試驗數據的離散性，零件和構件加工允許的尺寸偏差，材料中分佈的原始缺陷，以及受載零件危險部位應力響應的分佈特性等，都說明應力和強度以及影響它們的因素都是隨機變量，它們有各自的分佈形式，應該用概率統計理論和方法來處理，才能使疲勞強度在工程中所確定的壽命，成為保證某一概率下的可靠壽命。
  4. Measurement and characterization of surface texture is an important aspect of precision metrology. historically this has involved partitioning a profile into different wavelength regimes referred to as roughness, waviness and form followed by numerical quantization. parameters computed are then inspected for tolerance compliance to ensure a part performs its intended function. this approach is satisfactory when the specification has been carefully determined and the process is stable. however, when the manufacturing process is under development or when instability or modifications to the process invalidate specifications, there is a need to study surface finish parameters in relation to functional performance or process measures. in this context, the problem of surface texture classification and recognition are discussed. advanced techniques developed for this purpose along with applications are presented. also, the techniques discussed here will be useful across large bandwidth, from the characterization of nano scale to traditional micro scale surfaces

    表面結構的測量與特徵描述是精密計量技術的一個重要方面，傳統上包括將輪廓情況根據不同的波長范圍劃分為粗糙度、波紋度和形狀及后續的數字量化.按算得的參數檢查它是否為公差允許，以保證零件執行其指定的功能.當技術特性已經經過仔細確定，並且其過程穩定時，該方法是令人滿意的;但是，當製造過程正在進行中或過程的不穩定、過程變化使技術特性失效時，就需要研究和功能表現及過程評定相關的表面參數.討論了表面結構的分類與識別問題.同時闡述了為此目的而開發的先進技術及其應用.所研究的技術對從納米尺度到傳統的微米尺度的較大帶寬范圍內的表面特徵描述都是有效的
  5. It lets you capture statistics such as total counts, total time, and worst - case performance for requests, and it will also let you drill down into that information for database calls within a request

    它允許捕捉請求的總數、總時間以及最差情況性能之類的統計值，還允許深入請求中數據庫調用的信息。
  6. After working for half a year, the measurement system has the high reliability, according to the appraisement, it has far higher precision than maximal err 3 % which is regulated by china for level 1 measurement. the system has satisfied the design requirement

    該計量系統已運行半年多，經局技術監督處鑒定，其計量精度遠高於國家規定的天然氣一級計量最大允許誤差3 ，可靠性強，達到設計要求。
分享友人
分享到 Line

分享到臉書