緊固扭矩 的英文怎麼說
中文拼音 [jǐngùniǔjǔ]
緊固扭矩
英文
tightening torque- 緊 : Ⅰ形容詞1 (物體受到幾方面的拉力或壓力以後呈現的緊張狀態) taut; tight 2 (物體受外力作用變得固定...
- 固 : Ⅰ形容詞(結實; 牢固; 堅硬) firm; hard; solid Ⅱ副詞1 (堅決地; 堅定地) firmly; resolutely 2 [書...
- 扭 : 動詞1 (掉轉; 轉動) turn round 2 (擰; 旋轉) twist; wrench 3 (擰傷) sprain; wrench 4 (走路時...
- 矩 : 名詞1. (畫直角或正方形、矩形用的曲尺) carpenter's square; square2. (法度; 規則) rules; regulations 3. [物理學] moment
- 緊固 : [設計] fastening; fixture緊固桿 anchorage bar; 緊固環 dead ring; 緊固夾 anchorage clip; 緊固件 fa...
- 扭矩 : torsion; torque; twist; lay; moment of torque; moment of torsion
-
After proper operation has been verified, tighten all bolts using the crossover method. recommended tightening torques pattern is listed below
在檢驗操作能夠正常進行后,在採用交叉法緊固所有螺栓。推薦的緊固扭矩模式如下所示。Glossary of torque terminology for threaded fasteners
螺紋緊固件扭矩術語詞匯Railway rolling stock. screwed joint for electrical copper connections driving torque
鐵路機車車輛.電氣連接用銅螺旋旋入接頭.緊固扭矩Fasteners - tightening performance - torque angle simplified test method
緊固件.緊固性能.扭矩角度簡易試驗方法The joint surface normal stress is worked out and then the minimum sleeve press - in force, by which tightening bolt number is determined, ensuring that the sleeve is fastened and the desired torque is delivered
根據結合面的壓強計算了壓入襯套所需的最小壓入力,並依此確定緊固螺釘的數量,以確保壓牢襯套,滿足傳遞扭矩的需要。Fasteners - tightening performance - torque angle simplified test method ; german version en 14831 : 2005
緊固件.上緊性能.扭矩角度簡化試驗法Mechanical properties of fasteners - torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm
緊固件機械性能螺栓與螺釘的扭矩試驗和破壞扭矩公稱直徑1 10mmMechanical properties of fasteners - torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
緊固件機械性能.標稱直徑為1mm到10mm的螺栓和螺釘的扭轉試驗和最小扭矩Mechanical properties of fasteners. part 7 : torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
緊固件機械性能.第7部分:公稱直徑1 - 10mm的螺栓和螺釘的扭力試驗和最小扭矩Mechanical properties of fasteners part 7 : torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
緊固件的機械特性.第7部分:扭力試驗和標稱直徑為1mm - 10mm的螺栓和螺釘的最小扭矩Specification for hi - torque speed drive recess : dimensions and gauging for countersunk head fasteners
高扭矩快速旋入凹槽的緊固件規范:沉頭緊固件尺寸和測量Fasteners - torque clamp force testing
緊固件.扭矩夾持力試驗Fasteners - torque clamp force testing iso 16047 : 2005 ; german version en iso 16047 : 2005
緊固件.扭矩夾持力試驗Coatings on metal fasteners - specification for torque clamping force relationship
金屬緊固件塗層.扭矩夾緊力關系式規范分享友人