緊固螺栓 的英文怎麼說

中文拼音 [jǐnluóshuān]
緊固螺栓 英文
binding bolt
  • : Ⅰ形容詞1 (物體受到幾方面的拉力或壓力以後呈現的緊張狀態) taut; tight 2 (物體受外力作用變得固定...
  • : Ⅰ形容詞(結實; 牢固; 堅硬) firm; hard; solid Ⅱ副詞1 (堅決地; 堅定地) firmly; resolutely 2 [書...
  • : 1. [動物學] (軟體動物) spiral shell; snail; conch 2. (螺旋形的指紋) whorl (in fingerprint)
  • : 名詞1. (可開關的機件) bolt; plug 2. (塞子) stopper; cork
  • 緊固 : [設計] fastening; fixture緊固桿 anchorage bar; 緊固環 dead ring; 緊固夾 anchorage clip; 緊固件 fa...
  • 螺栓 : bolt; screw bolt; threaded bolt
  1. Bonded abrasive products. disc wheel with inserted nuts

    普通磨具.平形砂輪
  2. The two locking bolts should be tightened first in order to position the flanges correctly as shown in fig. 1

    為了如圖1所示正確定位法蘭,應該首先兩個鎖定
  3. Fasteners. bolts for corrugated steel pipes. part 0 : bolts related prescriptions screws nuts

    件.波紋鋼管用.第0部分:與有關的說明
  4. The main products range is various forged fasteners, pressed hardware and machining parts, inclusing non - standard bolt, high strength bolt, steel - strcture bolt, stude screws, double arming bolt, u - bolt or l - blot, tower bolt and other bolt, with hex head or square one according to the customer " s requirement

    該公司的主要產品為熱鐓成型的各種件和五金沖壓件具體類型:高強度、鋼結構、普通外六角、內六角、地角、雙頭、 「 u 」或「 l 」型、電力鐵塔、鐵路道釘、高速公路護攔、油井上用的各種專用和汽車配件。
  5. Tightening inspection for through bolts of main engine ( m. e. )

    主機貫穿度檢查。
  6. To irregular joints, fastness should start from bolts at assembly points to outside symmetrically

    對于不規則的接頭,應從拼接處的群對稱地向外側順序進行
  7. Repeat procedure with other body half and bolt together following the procedure noted above

    對另一半閥體重復同樣的步驟,然後按照上述步驟用在一起。
  8. The lid was bolted down

    蓋子用
  9. Specification for the use of high strength friction grip bolts in structural steelwork - metric series - general grade

    結構鋼制構件高強度摩擦緊固螺栓應用規范,米制系列.第1部分:普通
  10. Specification for the use of high strength friction grip bolts in structural steelwork - metric series - higher grade parallel shank

    結構鋼制構件中高強度摩擦緊固螺栓應用規范,米制系列.第2部分:高級
  11. 396 after seven days, the grouted mortar will have concreted, then we shall tighten the anchor bolts

    灌漿在七天以後凝,我們就將擰地腳
  12. Holding down bolt

    ,壓
  13. Failure analysis of the fastening bolt of the valve on the gas tower

    儲氣塔閥門緊固螺栓的斷裂分析
  14. The technical guide of ultrasonic inspection for high - temperature tight bolts

    高溫緊固螺栓超聲波檢驗技術導則
  15. Fastening bolt, binding bolt

    緊固螺栓
  16. Handle assembly is removed by loosening bolt and pulling upward. remove the two hold - down bolts and lift index plate from valve

    通過鬆懈並拔出方法拆卸手柄總成。拆卸兩個緊固螺栓,提起閥門上的刻度板。
  17. Attach each leg to the bottom of the enclosure using the three nuts, bolts, and washers provided for each leg. tighten bolts securely

    將每個支柱聯結到外殼底部,對于每個支柱,採用三套母、和墊圈與外殼進行連接。小心緊固螺栓
  18. Fasten bolt to fix distributor. regulate ignition timing, start up engine and make fine regulation to ignition advance angle at the time of idling speed to make engine to be stable while idling. acceleration should be sensitive and powerful which means a complete regulation is done

    調點火正時,啟動發動機,在怠速時對點火提前角做細微調整,使發動機在怠速階段平穩,加速時應明顯感到快捷有力,即調整完畢,擰分電器緊固螺栓
  19. Rebar and anchor bolts used in the pump base shall be sufficiently tied to the mounting floor to ensure a rigid, stable mounting surface for the pump unit

    泵基座所採用的鋼筋和錨應該能夠與安裝地面結合牢密,確保為泵設備提供堅可靠的安裝基礎。
  20. Specification for hydraulic port and stud coupling using ' o ' - ring sealing and ' g ' series fastening threads

    用o型圈密封及g系列紋的液壓系流入口及連接規范
分享友人