線圈磁化 的英文怎麼說

中文拼音 [xiànjuāncíhuà]
線圈磁化 英文
coil magnetization
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 圈 : 圈名詞1. （養豬羊等牲畜的建築） pen; fold; sty 2. （姓氏） a surname
  • 磁 : 名詞1. [物理學] （磁性; 能吸引鐵、鎳等的性質） magnetism 2. （瓷） porcelain; china
  • 線圈 : [電學] coil
  1. During the winding of magnetic pole coils used in synchronous electric motors, cold hardening is induced by press bending at 90, by which the coils are hard to be pressed and shaped, thus local resistivity increases and results in influence on the coil lifetime

    摘要同步電動機磁極線圈在編繞加工時， 90角處因壓彎而產生的冷作硬化現象使線圈無法裝壓成型，且局部電阻率增大，甚至影響磁極線圈使用壽命。
  2. As a result, the electromagnetic field intensity is changed accordingly and fluctuating current in the damper coil is created. damping force is mostly produced because of the phase difference between fluctuating current and displacement of rotor. the formulas of fluctuating current and damping coefficient are deduced theoretically, and the calculated results are consistent with the experimental results

    通過分析發現電磁阻尼器線圈內由於轉子渦動時變化的磁場而產生的波動電流與轉子位移間的相位差是產生阻尼的主要原因，推導了波動電流、阻尼系數的計算公式，並通過實驗展示了被動式電磁阻尼器的阻尼效應。
  3. The common principle is the use of the induction of an electromotive force by the variation of the magnetic flux through a coil.

    一般原理均是使用通過線圈的磁通量變化感應的電動勢。
  4. The fluctuating mangnetic field cutting across the turns or loops of wire of the secondary coil sets up an electrical pressure or voltage in these loops.

    起伏變化的磁場橫向切割著次極線圈的線匝和線環時，會在這些線環中引起電壓。
  5. The fluctuating magnetic field cutting across the turns of loops of wire of the secondary coil sets up an electrical pressure or voltage in these loops.

    起伏變化的磁場橫向切割著的次級線圈的線匝或線環時，會在這些線環中引起電壓。
  6. The subject of this thesis is to study ironless moving coil linear permanent magnet synchronous motor and the major works in this thesis are summarized as follows : 1 ) two analytical formulas are derived by concentrated current method and distributed current method to determine the magnetic field due to pm, based on the current model of pm. besides, two method ( magnetic charge method and solution by laplace equation method ) are also introduced with comparing their advantages and disadvantages. then the effects of the motor parameters on the flux distribution are discussed

    本文對空芯動圈式直線同步電動機進行了深入細致的研究，內容包括： （ 1 ）採用電流模型推導出兩種計算永磁磁極二維氣隙磁場的解析公式（集中電流法、分佈電流法） ，同時介紹了兩種永磁電機氣隙磁場計算方法（磁荷法，直接求解拉氏方程法） ，分析各種方法的優缺點，討論電機參數對氣隙磁密的影響； （ 2 ）介紹了單層同心繞組的布置方式，根據安培定律推導出空芯動圈式直線永磁同步電動機的靜推力計算公式，分析靜態力?位移特性； （ 3 ）建立空芯動圈式直線永磁同步電動機動態模擬模型，模擬不同驅動方式下電動機起動、穩態運行時電磁力、速度、位移的變化情況。
  7. Based on the finite element model, simulated results on the flux distributions under different excitation a ampere - turns and positions were obtained, discussion on the cause and characteristics of its stroke versus displacement were also given

    採用永久磁鐵產生的極化磁場與線圈產生的控制磁場形成差動磁路作用於銜鐵，使之實現雙向驅動。
  8. A precision force banacing accelerometer for ineration navigation application is developed. the resolution, low - sensitivity threshold and high thermal stability are considered as design parameters. in order to guarantee a low - sensitivity threshold while maintaining robustness against shock, push - pull type long flexures are used in this paper. to improve thermal stability, this paper discusses the use of electromagnets as a magnetic fied source. the silicon pendulum assembly and modified inducance type pick - up is also developed to reduce assembling procedure. the measure range of accelerometer is 0 - 70g

    加速度計的解析度、靈敏度閾值和高的熱穩定性是設計時主要考慮的參數。本論文中使用推?挽式長撓性結構來保證低靈敏度閾值，同時保證抗振魯棒性。為了提高熱穩定性，本文中討論了利用永久磁鐵作為磁場源；微加工技術被引入擺組件的結構設計和利用力矩線圈作為激勵線圈來簡化電感式的檢測裝置。
  9. Under windows nt and labview development environment, using the linear fit module, exponential fit module > general polynomial fit module of labview to design a method for fitting the experiment data, the results of curve fitting indicate that the purpose of general polynomial fitting is better than the rest. separating the equivalent input impedance of magnetostrictive transducers without stimulate current from input impedance of it with stimulate loop based on the results of curve fitting, and determining the syntony frequency and electric simulation network parameters of magnetostrictive transducers by this input impedance. finally, with labview network functions, realizing magnetostrictive transducer electric simulation system based on web server and discussing a scheme for this system network by datasocket. the method of this paper can more accurately determine the syntony frequency and electric simulation network parameters of magnetostrictive transducers than the testing method of syntony & anti - syntony. at the same time, discussing virtual instrument measurement system and how to realize magnetostrictive transducer electric simulation network system by labview network functions of network virtual instrument measurement development environment

    在windowsnt系統環境和labview虛擬儀器技術開發平臺下，首次利用labview中的直線擬合模塊、指數擬合模塊以及多項式擬合模塊，設計了一種對實驗所得數據進行曲線擬合的方法，對三種擬合方法進行了比較，曲線擬合結果表明，多項式擬合方法相對于其它兩種擬合方法效果更好；根據曲線擬合的結果可從帶激勵線圈的磁致伸縮換能器的輸入阻抗中分離出磁致伸縮換能器鐵芯在無激勵電流時機械振動形成的等效輸入阻抗，並由此輸入阻抗確定了磁致伸縮換能器的諧振頻率及其電氣模擬網路參數；最後通過labview提供的網路功能，實現了基於web服務器的磁致伸縮換能器電氣模擬虛擬儀器測試系統，並探討了通過datasocket技術實現該系統網路化的方案。
  10. Based on many references form civil and abroad, the author mainly studies the measurment theory and method for flux, raising height, axial power and rotational velocity. avoiding many complicated and intermediate courses for power wastage analysis, introduces the electric measurement and using efficiency curve of motor in measureing axial power, and satisfies the automatization of the device. the paper also provides a new method, inductive winding, in measuring rotational velocity of electromotor, supplys limitations of other method in measuring rotational velocity of electromotor in water, and meet practical needs in developing diving electric pump for corporation

    作者在參閱大量國內外有關文獻，著重探討了水泵流量、揚程、軸功率、轉速的測試原理和測試方法，提出了採用電測法並結合電機效率特性曲線測量水泵軸功率，從而避免了損耗分析法中大量復雜的中間過程，滿足了試驗裝置的自動化測量要求；採用漏磁感應線圈法測量電機轉速，彌補了其它轉速測量方法對水下電機測試的局限性，適應了萊恩公司開發潛水電泵的實際需要。
  11. Electromagnetic heat is generated from the coils that are transmitted with high frequency electric currents, when magnetic metal cookware is used, high magnetic frequencies are generated, thereby creating huge volumes of whirling fluids, which is transformed from electric power into heat power

    電磁爐具熱源的產生是利用高頻電流通過一組線圈，形成高頻交變磁場，磁場的磁力線穿過鐵磁材料的金屬鍋，作用於鍋體內的粒子，使其劇烈運動、磨擦，即時產生極高的溫度場，將電能轉化成熱能。
  12. Report back in the exhibit schedule : march 8, 2006 - 10 days am09 : march 10, 2006 - 12 days remove time : march 12, 2006 exhibitors range : car, car, motorcycle, light truck bearings, railway bearings, magnetic bearing spindle ; aviation aerospace marine bearings, rocket and satellite bearings ; industrial robot bearings, machining center and machine spindle bearings, textile machine bearings, motor bearings, and farm machinery bearings, paper machine bearings, bearings press, bearing mill, metallurgical mining, petrochemical machinery bearings, bearings sporting goods, marine rig bearing ; bearings, bearings gyroscope, high - precision bearings, high - speed bearings, linear motion bearings, needle roller bearings, thrust bearings, ultra - low - temperature bearings, special bearings, ceramic ball bearings, spherical with trophies bearing miniature bearings, quiet motor bearings, ball bearings, roller bearings, lubricating bearings corrosion resistant bearings, bearing joints ; bearing ring blank refinement, precision ball and roller crown, with nails cage

    撤展時間： 2006年03月12日參展范圍：轎車汽車摩托車輕型車軸承鐵路軸承磁懸浮軸承電主軸航空航天航海軸承火箭及人造衛星軸承工業機器人軸承加工中心及機床主軸軸承紡織機軸承電機軸承農機軸承造紙機軸承印刷機軸承軋機軸承冶金礦山石油化工機械軸承體育用品軸承海洋鉆機軸承組合軸承陀螺儀軸承高精軸承高速軸承直線運動軸承滾針軸承推力軸承超低溫軸承特種專用軸承陶瓷球軸承帶座外球面軸承微型軸承靜音電機軸承球軸承滾子軸承潤滑軸承耐腐蝕軸承關節軸承軸承套圈精化毛坯精密鋼球凸度滾子帶釘保持架軸承滾動體等軸承部件。
  13. Magnetic head is designed by six magnetic poles in symmetrical distribution, the design of excitation loop and excitation angle makes magnetic field act on welding arc region which could control welding arc effectively. the insulation, cooling and hermetization of magnetic head avoid the influence on magnetic field of outside ; miniaturization design of magnetic head could achieve different welding process

    磁頭裝置採用六磁極對稱勵磁方式設計，勵磁線圈和勵磁角度的設計使產生的磁場恰好作用於焊接電弧區域以實現對電弧的有效控制;磁頭的絕緣，冷卻，密封設計避免了焊接過程中外界因素對磁場的干擾;磁頭整體的小型化使該裝置可以實現多種形式的焊接工藝。
  14. This paper presents an adaptive control for the semi - active suspension using the combination of mr damper and feedback neural networks. analyzing the mr damper, a smart actuator, chapter 3 gives the design of pre - amplifier of current, which provides the external magnetic field. and it discusses the additional nonlinear stiffness resulted from the transition of mr fluid from liquid to semi - solid or solid

    在分析新型智能材料用做作動器的磁流變阻尼器特性的基礎上，本文給出阻尼器線圈的前置電流放大電路，並討論了因磁流變液體固液態之間的可逆變化而產生的懸架系附加非線性剛度。
  15. 2 ) the inductance transducer used to identify large wear particle is developed. the analytical theory of wear particle and detection windings are expatiated and inner magnetic distribution of inductance transducer is discussed, the geometry parameters are optimized by using genetic algorithm, and the finite element analysis method is used in the designing

    2 ）研製了識別大磨損顆粒的材質和測定其粒度的電感傳感器，闡述了磨損顆粒與檢測線圈的解析關系，探討了傳感器的理論基礎，分析了電感式檢測傳感器內部的磁場分佈，並應用遺傳演算法優化了傳感器幾何參數，最後進行了有限元模擬分析。
  16. The advantage of this method is that, the compensation loop is applied for eliminating the change of toroidal flux produced by the toroidal coils and the adjustable structure can be used to decrease the error signals come from the poloidal field

    該方法的優點是補償線圈有效地消除了縱場線圈產生的磁通變化，而調節機構能降低來自極向場的誤差信號。
  17. It is found from the experiment that under the conditions of peak magnetic field of 0. 57t, beam pulse fwhm ( full width of half maximum ) of 44ns, a microwave radiation pulse with fwhm 25ns and whole width of 35ns is produced, when the intensity of the guiding magnetic field rises, the peak microwave power changes little but the width of the pulse reduces. the a - k gap also has obvious influence on the microwave radiation, the stable and higher microwave output is obtained under suitable gap

    實驗中還發現，在峰值磁場0 . 57t和束流半高寬44ns情況下，得到了25ns半高寬和35ns底寬的微波脈沖信號，隨著導引磁場增加，微波信號幅值基本不變，但國防科學技術大學研究生院學位論文是微波脈沖寬度會逐步減少;實驗中還發現磁場線圈位置有一定的軸向調節范圍，說明在磁場軸向分佈的一定變化范圍內，器件都可以正常工作，這對以後的永磁場系統導引的微波實驗有利。
  18. Sb2011 precise decade inductance box adopts loop inductance coil, emc screen, special temperature compensation structure, aging technology, and whole - seal moistureproof measure therefore, it possesses many special characteristics, such as strong anti electromagnetic capability, little effect by humidity and temperature, perfect stability, reliable performance, strong adaptability, novel structure, and easy to operate

    Sb2011型精密十進位電感箱採用鐲環形電感線圈及電磁屏蔽，獨特的溫度補償結構與老化處理工藝並採取全封閉式的防潮措施，具有抗電磁干擾能力強、受濕度與溫度影響極小、穩定性好、性能可靠、適應性強、結構新穎、操作方便等獨特優點。
  19. Based on the effective mass theory and critical state model, an anisotropic theory of critical current and ac losses for single hts tape and tape stacks were established. analytical formulae were presented to calculate critical currents and ac losses with an arbitrary angle between the wide side of hts tape and the direction of ac or dc applied fields. from the anisotropic theory of ac losses of hts sample, a numerical model to calculate ac losses of hts coil was developed

    基於臨界態模型與高溫超導體的有效質量理論，建立了高溫超導帶材及並聯堆疊帶材的交流損耗與臨界電流的各向異性理論模型；給出了高溫超導帶材的交流損耗及臨界電流隨（交、直流）背景磁場與超導帶面夾角變化規律的理論公式；依據所建立的高溫超導短樣帶材的各向異性理論公式，給出了高溫超導線圈交流損耗的數值計算模型；並利用該模型，計算了高溫超導雙餅線圈的交流損耗；並與實驗測量結果進行了比較分析。
  20. The current estimated normalized magnetic field direction, corrected for the fields generated by the torque coils

    目前經由修正轉矩線圈產生的磁場而估計到的正規化磁場方向。
分享友人
分享到 Line

分享到臉書