縱向接合板 的英文怎麼說
中文拼音 [zōngxiàngjiēgěbǎn]
縱向接合板
英文
longitudinal fish plate- 縱 : Ⅰ動詞1 (釋放; 放走) release; set free; let go 2 (放任; 不約束) indulge; give oneself up to; l...
- 接 : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
- 合 : 合量詞(容量單位) ge, a unit of dry measure for grain (=1 decilitre)
- 板 : Ⅰ名詞1 (片狀硬物體) board; plank; plate 2 (專指店鋪的門板) shutter 3 [音樂] (打拍子的樂器) ...
- 縱向 : [造紙] direction; machine direction; endwise; longitudinal direction; vertical; longitudinal縱向...
- 接合 : joint; zygosis; juncture; articulation; concrescent; nexus; coaptation; syndesis; synapsis; meet;...
-
Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior
分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大,實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著,而連接端板厚度及剪力連接程度的影響則不是太顯著。The comb tenoning machine is newest automatically, manual mx3510 4010 4012 4014 4016 mainly uses in hitting, the short lumber splicing comb tenon, specially to produces the joiner board, the prop, the furniture and so on, it raises the lumber use factor, in order to the longitudinal agglutination joining - up makes the long size the specification material ideal processing equipment
簡要說明梳齒機最新自動、手動型mx3510 、 4010 、 4012 、 4014 、 4016型主要用於中、短木材的拼接梳齒榫,特別對生產細木工板、支柱、傢具等,它不僅提高木材的利用率,而且便於縱向膠合併接製成長尺寸的規格料的理想加工設備。The comb tenoning machine is newest automatically, manual mx3510 4010 4012 4014 4016 mainly uses in hitting, the short lumber splicing comb tenon, specially to produces the joiner board, the prop, the furniture so on, it raises the lumber use factor, in order to the longitudinal agglutination joining - up makes the long size the specification material ideal processing equipment
梳齒機最新自動、手動型mx3510 、 4010 、 4012 、 4014 、 4016型主要用於中、短木材的拼接梳齒榫,特別對生產細木工板、支柱、傢具等,它不僅提高木材的利用率,而且便於縱向膠合併接製成長尺寸的規格料的理想加工設備。The concept of adding the contribution of rebar to a bare steel connection is utilized to form the stiffness of composite semi - rigid joints under hogging moment. upon this basis, the calculating formulas of initial rotation stiffness are presented. the calculated results show to be in good agreement with the test results
本文認為,在負彎矩區,組合節點的轉動剛度是由混凝土板內縱向鋼筋與樑柱型鋼連接部分各自的貢獻疊加而成的,為了簡化計算,這里忽略了受拉混凝土對節點轉動剛度的影響。A high degree of continuity can be achieved just providingthe slab with rebar running along the column. furthermore, stiffness and ultimate resistancecan be controlled in a rather simple way by a suitable selection of steel connection detailingand amount of reinforcement
這種組合節點可以通過混凝土板內的縱向鋼筋實現組合梁在不同跨之間的連續性,而且通過選擇合適的型鋼樑柱連接方式和縱向鋼筋數量,可以有效地控制節點的剛度與承載能力。The study on the behavior of semi - rigid joints in steel - concrete composite frames gets widely attention recently. a high degree of continuity can be achieved at a very low cost just providing the slab with rebar running along the column. furthermore, stiffness and ultimate resistance can be controlled in a rather simple way by a suitable selection of steel connection detailing and amount of reinforcement
鋼-混凝土組合框架中半剛性組合節點性能的研究近來引起了廣泛的關注,這種節點形式花很低的成本就可以通過混凝土板內的縱向鋼筋實現組合梁在不同跨之間的連續性,而且通過選擇合適的型鋼樑柱連接方式和縱向鋼筋數量,可以有效地控制節點的剛度與承載能力。分享友人