縱梁 的英文怎麼說

中文拼音 [zōngliáng]
縱梁 英文
carline =carling
  • 縱 : Ⅰ動詞1 （釋放; 放走） release; set free; let go 2 （放任; 不約束） indulge; give oneself up to; l...
  • 梁 : 名詞1 （屋架中架在柱子上的長木） beam 2 （通常也指檁） purlin 3 （橋） bridge4 （物體中間條狀隆起...
  1. Simulation analysis of the lengthways warp of truck carling outside board

    卡車縱梁外板縱向翹曲的模擬分析
  2. The simulation and application of ergonomics to the working procedure of a front - carling assembly

    轎車前縱梁總成工序的人機工程研究
  3. The irrepressible bloom, who also had a shrewd suspicion that the old stager went out on a manoeuvre after the counterattraction in the shape of a female, who, however, had disappeared to all intents and purposes, could, by straining, just perceive him, when duly refreshed by his rum puncheon exploit, gazing up at the piers and girders of the loop line, rather out of his depth, as of course it was all radically altered since his last visit and greatly improved

    他定睛一看，才勉強辨認出那個灌了一肚子朗姆酒精神隨之而振的水手，正毋寧說是出神地仰望著環行線的陸橋橋墩和縱梁。當然自從他最後一次踏訪，這里已大大地改建，面目一新了。看不見形影的某人或某些人把男子小便池指給他看，那是衛生委員會為了衛生而到處蓋起來的。
  4. During fabrication slots for the stringers flanges were flame cut into box girders.

    製造時，為安裝縱梁翼緣，在箱型梁中用焰割法開槽口。
  5. The longitudinal girder forms part of the parapets.

    縱梁成為欄桿的一部分。
  6. Two structures that experienced cracking in the longitudinal girder web at x-type cross-frame are reviewed in detail hereafter.

    以下將詳細評論在縱梁腹板與X型橫向框架連接處開裂的兩座結構。
  7. The test results from the standard circles with different radii and the industrious application of the stiffening plate of santana ' s front longeron were presented

    給出了以不同半徑的標準圓進行測試的結果和以桑塔納轎車前縱梁加強板為例進行的工業應用。
  8. Technology and structure features of main equipment of cold bending production line of auto longeron have been introduced with brief to keys of design and debugging and solutions to frequent problems arising in debugging process

    摘要介紹了汽車縱梁冷彎成形生產線的工藝路線、主要設備的結構特點；簡述了汽車縱梁冷彎成形工藝的設計關鍵及調試要點；給出了生產線調試過程中的常見問題及解決方案。
  9. These structures were usually skewed with the diaphragms placed perpendicular to the longitudinal girders.

    這些結構通常是斜交的，而橫隔板則垂直於縱梁布置。
  10. Punching line for truck side - member and side panel of carriage

    卡車縱梁及車廂邊框沖孔線
  11. The initial retrofit consisted of removing the gaps between the stringer flange and floor beam by providing shims.

    最初的修復工作是通過墊片來消除縱梁翼緣和橫梁之間的間隙。
  12. Stringer webs have cracked in suspension bridges at the stringer-floor beam connections.

    在懸索橋的縱梁和橫的連接處，縱梁的腹板上發生開裂。
  13. Two structures that experienced cracking in the longitudinal girder web at x - type cross - frame are reviewed in detail hereafter

    以下將詳細評論在縱梁腹板與x型橫向框架連接處開裂的兩座結構。
  14. This thesis also studied the influence of the spacing, which is between the central action point on the shackle and the exterior plate of the chassis frame side rail, because the spacing influenced the local stress distribution and the stress concentration of the bus body frame and the chassis frame, and the related variational tendency was summarized

    本文還研究了吊耳銷作用力中心點與縱梁腹板間距對車架和客車骨架的應力分佈與集中的影響，總結了相關的變化趨勢。
  15. At last, this paper summarized the study and pointed out the development of detecting missing holes on auto - carling in future

    最後總結課題研究，並對汽車縱梁漏孔檢測的發展作了展望。
  16. The traditional method completely depends on the workers and is inefficiency. this paper mainly introduced an automatic measurement of missing holes on the auto - carling. the basic technique used in this measurement is image processing

    本文介紹了一種利用圖像處理技術實現汽車縱梁漏孔檢測的方法，並在此基礎上完成了「汽車縱梁漏孔自動檢測裝置」研製。
  17. The traditional detecting missing holes on auto - carling is carried on through a artificial way. mainly, the workers detect the missing holes through compared auto - carling with the standard autocad blueprint and use micrometer calipers to measure the positions of holes

    傳統汽車縱梁漏孔檢測主要以人工方式進行:檢測工人把縱梁和標準縱梁autocad圖紙進行比對來檢測是否有漏孔、用千分尺等工具手動測量孔心位置是否合乎要求。
  18. Firstly, the basic knowledge about image processing and auto - carling was introduced. after a deep analysis on how to use an image processing system to detect the missing holes on auto - carling, we design the whole system combined with the actual conditions of auto - carling. afterwards we expound the whole system ’ s hardware and software particularly

    本文首先對圖像處理相關知識、縱梁基本知識、漏孔檢測參數和特點進行簡單介紹，然後對如何根據縱梁漏孔檢測的實際情況構建一數字圖像處理系統來實現縱梁漏孔檢測進行了分析，並給出了總體方案。
  19. Improving welding prcedure for vertical trussing

    車架縱梁焊接工藝的改進
  20. The practicality space analysis method of structure calculation for large rectangle aqueduct with multi - longitudinal beam

    大型多縱梁矩形渡槽受力計算的實用空間法
分享友人
分享到 Line

分享到臉書