縱長軸 的英文怎麼說

中文拼音 [zōngzhǎngzhóu]
縱長軸 英文
fore and aft axis
  • 縱 : Ⅰ動詞1 （釋放; 放走） release; set free; let go 2 （放任; 不約束） indulge; give oneself up to; l...
  • 長 : 長Ⅰ形容詞1 （年紀較大） older; elder; senior 2 （排行最大） eldest; oldest Ⅱ名詞（領導人） chief;...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  1. Sonographic examinations of the pancreas were performed by sagittal scanning at the epigastrium ; the long axis and short axis of the oval cross - sections of both the pancreatic head and body were measured

    檢查測量的方式是在上腹部作縱向掃描，可以分別得到胰臟頭部與體部之圓形縱切面造影，進而分別測量胰臟頭部與體的長軸與短軸，一共為4個胰臟因數。
  2. Chang da railway, ha da and sheng da highway run through the city from south to north, the convenient traffic sets up a bridge for wafangdian guang yang bearing group to domestic and international markets

    長大鐵路，哈大公路和沈大高速公路縱貫南北，便利的交通為瓦房店光陽軸承集團架起了通向全國走向世界的橋梁。
  3. The distrbution function of intersections is proposed for the case that a long needle is thrown randomly in a double grid system ( equally unit - spaced )

    摘要考慮在間距為1的區域足夠大的方格子系統中投入長度為（ 0 ， + ）的針時，針與方格子的橫軸和縱軸的交點總數的分佈問題。
  4. The parameters are measured respectively during the experimental process, such as bearing capacity, deformation, strain and so on. it concludes that when the other conditions is equal, the limit bearing capacity of the concrete filled steel tube long column subjected to axial compress is reduced along with the long diameter ratio increased

    從試驗結果可以看出：鋼管混凝土軸心受壓長柱的穩定承載力，在其他條件相同時隨長細比的增大而逐漸降低；試件在最大承載力狀態下，鋼管表面的平均縱向應變已超過鋼管的屈服應變值，破壞呈現為非彈性失穩破壞。
  5. At last, we can get the limit bearing capacity formula of concrete filled steel tube long column subjected to axial compress. on the basis of the theoretical analysis, twelve samples which have four kinds of long diameter ratio are studied experimentally

    在理論推導的基礎上，對四種長細比12個鋼管混凝土軸心受壓長柱進行了試驗研究，量測了鋼管混凝土軸心受壓長柱在試驗過程中各階段的承載力、應變、縱向變形系數等。
  6. In paper, it introduces their characters one by one. 3 ) axle center and partial pressed component when the longitudinal pressure is through the axle center of component, we call it as axle center pressed com

    3 ）軸心受壓構件與偏心受壓構件縱向壓力通過構件截面重心的構件稱為軸心受壓構件c軸心受壓構件可分為短柱和長柱兩大類。
  7. Thereinto, the controlling method is altered into air cylinder control installed on two sides of transmission shaft, steel structure platform and rushing - board brake. these alterations enable the equipment to be more sensitive and reliable for controlling. steel structure platform makes noise giving off when equipment operates greatly decrease and rushing board brake prolongs the service life of friction belt because it owns large braking area which can contact flywheel and gain large moment and then do little harm to friction belt

    二j53 - 630b型在j53 - 630a型的基礎上作了改進，其中操縱方式改為裝在傳動軸兩端的氣缸操縱，剛結構式平臺，推板式剎車這樣使設備的操縱更靈敏可靠剛結構式平臺使設備工作時噪音大大降低，推板式剎車由於剎車板剎車面積大與飛輪的接觸均勻，所以剎車力矩大同時對摩擦帶的損傷小，延長摩擦帶的使用壽命，推板式剎車平行調整故調整方便。
分享友人
分享到 Line

分享到臉書