織金洞 的英文怎麼說
中文拼音 [zhījīndòng]
織金洞
英文
zhijin cave-
In the course of commercialization reform of financial institutions, inanition in fund emerges in the countryside areas. worse of all, the incomplete financial services and products, the imperfect rural financial organizational system together with deficient new financial institutions such as agricultural insurance and agricultural venture capital fail to meet the demands of agricultural industrialization ' s iurther development
在當前我國廣大農村地區,由於金融機構商業化改革,不僅開始出現金融空洞化,使得農業產業化發展資金供給嚴重不足,而且金融機構的金融服務和金融產品的不完善,農村金融組織體系的不健全,農業保險、農業風險投資等金融新機制的短缺,更是無法滿足農業產業化發展對農村金融提出的更高要求。Zhijin cave scenic spot : the largest cave in asia, travel for cave, come to zhijin
織金洞景區:黃山歸來不看山,織金歸來無洞天。( 3 ) there are many flaws in direct laser metal sintering, such as the high remnants stress, micro - hole and micro - crack in sintering parts. in order to solving those problems, the programming of scanning paths is put forward, and several parts are prepared with different scanning paths respectively. the following conclusion is educed : the parts produced with short - side scanning path and same scanning direction have the minimum structure, the rigidity of parts prepared by short - side and same direction scanning path is highest, and the density of parts produced with the vertical scanning path is maximal
( 3 )針對採用大功率激光直接燒結鎳基高溫合金成形金屬零件存在的問題,如較大的殘余應力,製件中存在著微裂紋、微孔洞等缺陷,初步提出掃描路徑的規劃,並採用幾種不同的掃描方式進行燒結試驗,發現採用短邊掃描路徑和同向掃描能夠獲得更加細小和分佈均勻的組織結構,採用短邊同向路徑制備的試樣其顯微硬度最高,而採用變向掃描(垂直)路徑制備的試樣緻密性最好。Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great
採用雙向楔形壓制,大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時,大的孔洞變形破碎為小的孔洞,或呈線狀孔;隨著高向變形量的增加,顆粒進一步變形,孔洞進一步破碎,大孔「吞併」小孔,小孔塌陷並逐步消失;當高向變形量達到60 %時,孔洞量大為減少,材料基本緻密,組織趨于均勻,楔壓坯料的密度、硬度變化曲線接近水平線,坯料的相對密度達99 . 7 % ,抗拉強度_ b = 408mpa ,屈服強度_ ( 0 . 2 ) = 289mpa ,延伸率= 13 . 6 % ;對比其它的壓制溫度,在450楔形壓制的坯料組織均勻,孔洞及顆粒邊界基本消失,顆粒之間冶金結合良好。Analyzing those population variables, we find that women pay more attention to ethics than men do ; state - owned enterprises pay more attention to organizational awareness and interpersonal understanding while enterprises in the three forms of joint venture, cooperative business and exclusively foreign - owned enterprises in china team management and leadership and personal driving ", financial industry wishes middle - level managers having high adaptability and flexibility while manufacturing industry and high & new technology industry innovation, service industry communication
通過對性別、年齡、職位、企業性質、行業類型等人口變量的分析,發現:女性比男性更加看重「正直誠信」這一企業中層管理人員勝任特徵,國有企業更注重中層管理人員的「組織洞察力」 、 「人際洞察力」 ,而三資企業更看重「團隊管理與領導」和「個人驅力」 。金融業要求中層管理人員具有很強的「適應性和靈活性」 ,製造業與高新技術業要求他們有很強的「創新性」 ,而服務業則更需要「溝通」能力。分享友人