繪圖用圓規 的英文怎麼說
中文拼音 [huìtúyòngyuánguī]
繪圖用圓規
英文
compass for drawing- 繪 : 動詞（畫出圖形; 描寫） paint; draw
- 圖 : Ⅰ名詞1 （繪畫表現出的形象; 圖畫） picture; chart; drawing; map 2 （計劃） plan; scheme; attempt 3...
- 用 : Ⅰ動詞1 （使用） use; employ; apply 2 （多用於否定: 需要） need 3 （敬辭: 吃; 喝） eat; drink Ⅱ名...
- 規 : Ⅰ名詞1 （畫圓形的工具） instrument for drawing circles 2 （規則; 成例） rule; regulation 3 [機械...
- 繪圖 : plot; draw; sketch; plotting; mapping繪圖板 drawing board; field plotter; plotting board; plottin...
-
Compass with interchangeable points for precision drawing instruments
精密繪圖儀用插腳式圓規Drawing instruments - lengthening bar for big bow combination with interchangeable parts
繪圖儀.大圓規用接長鑲配腳Especially, when the isocline of x is monotone decreasing in 0 < x < 1, the svstem has no limit cycle and is globally stable ; next, we construct a saddle bifurcation at the boundary equilibrium and a degenerated bogdanov - takens bifurcation at the interior equilibrium by choosing appropriate parameter values in the following two sections, where our work are based on the theory of central manifolds and normal torms. we prove that is a codimention 3 focus - type equilibrium. system ( 6. 1 ) will have two limit cycles at some appropriate bifurcation parameter values, and have homoclinic or double - homoclinic orbits at some other appropriate bifurcation parameter values ; at last, we study the qualitative properties of the system at infinite in the poincare sphere
因為系統在（ 0 ， 0 ）點處沒有定義，這給研究其在（ 0 ， 0 ）附近的動力學性質帶來了困難，我們應用文獻[ 17 ]中關于研究非線性方程奇點的系列理論和方法，圓滿解決了這一問題，給出了第一象限內當t +或t -時，在全參數狀態下系統的軌線趨于（ 0 ， 0 ）點的所有可能情況，其相圖也得以描繪；並且，系統不存在極限環的幾個充分條件我們也予以列出，當x的等傾線在0 x 1范圍內遞減時，系統不存在極限環，全局漸近穩定；然後，我們以中心流形定理和正規型方法為主要工具，巧妙選擇參數，分別構造了一個余維2的鞍點分岔和一個余維3退化bogdanov - takens分岔，證明了平衡點是余維3的焦點型平衡點，存在參數， m ，的值使得系統（ 6 . 1 ）有兩個極限環，還存在參數， m ，的另外值使得系統（ 6 . 1 ）有同宿軌或雙同宿軌。Fixed centre spring bow with interchangeable points for precision drawing instruments
精密繪圖儀用帶互換筆尖的圓心固定式彈簧圓規Firstly, the distortion of rolled piece and the designing method in the beforehand slit pass and slit pass has been analyzed. secondly, based on the research production of predecessor and research of the author, card system selected some corresponding experience formulas such as roll force, roll moment, roll temperature and roll consume, and established spread model in the beforehand slit pass and slit pass and the distribution model of elongation coefficient. subsequently, card system applied the dynamic programming method with minimum roll consume and optimized its pass system
本文以圓鋼雙線切分為基本實體模型，著重分析了預切分孔型和切分孔型在軋制過程中的變形特點及相應的孔型設計方法；基於前人的研究成果及作者的探索，選擇了相應的軋制力、軋制力矩、溫度及能耗模型，建立了預切分和切分的寬展及延伸系數的分配模型；應用動態規劃法以能耗最小為目標函數對孔型系統進行了優化設計；利用visualbasic6 . 0和microsoftaccess數據庫的連接，建立了數據查詢系統，以visualbasic6 . 0和autocad之間的介面在vb環境下完成了斷面孔型圖的繪制。分享友人