纖滑石 的英文怎麼說

中文拼音 [xiāngǔdàn]
纖滑石 英文
agalite
  • 纖 : 纖形容詞（細小） fine; minute
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  • 石 : 石量詞（容量單位, 十斗為一石） dan, a unit of dry measure for grain （= l00 sheng）
  1. Taking the brown alumina powder and french chalk as the refractory, the silicasol and dextrin as the composite binder, the western bentonite and sodium carboxymethyl cellulose ( cmc ) as the composite suspension agent, the optimum mixing ratio of the water - based coating was established by the method of orthogonal experiments

    摘要選用棕剛玉粉及滑石粉為耐火填料，以硅溶膠及糊精為復合粘結劑，以鈉基膨潤土和羧甲基纖維素鈉（ cmc ）為復合懸浮劑，通過正交試驗方法確定了最佳配方。
  2. The best technical condition of the reed pulp is in 47 sr, wipped off primary fines and added secondary fines up to 10 %, meanwhile, adding stuffings ( abietic acid, vitriolic aluminium, french chalk )

    漂白蘆葦漿抄造文化用紙的最佳工藝條件為：在打漿度為47 sr時去除一級細小纖維，加入10 %的二級細小纖維，同時加入填料（松香膠、硫酸鋁、滑石粉） 。
  3. After looking up a large amount of native and foreign information, the materials used in the experiment were as follows : ptfe base, graphite filler, molybdenum disulfide filler, copper powder filler, carbon fiber and so on. the experimental method is that the formula was designed according to uniform experimental method, the relationship between formula and frictional property was found with spline function and then the representative test points were chosen from fitting curve to make verification test for optimization. the preparative technique of solid lubricant is cold - press sintering method

    經過查閱大量國內外文獻資料后確定原料為：聚四氟乙烯樹脂為基體，加入石墨、二硫化鉬、銅粉、碳纖維等填料；試驗方法為：根據均勻試驗方法設計配方，用樣條函數找出配方與摩擦性能的關系，然後在擬合曲線上選取具有代表性的試驗點進行驗證試驗，達到優化的目的；制備工藝：冷壓燒結法制備固體潤滑劑。
  4. The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film

    試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。
  5. The result of md simulation means that : ( 1 ) the microstructure in the amorphous carbon has no obvious change, the slippage which is parallel to the fiber axes in the graphite slices of the pyc interphase was found ; ( 2 ) bulk moduli of every part of interphase diminished, young ' s moduli in all three direction of amorphous carbon diminished, young ' s moduli of the graphite slices in the direction of parallel to the fiber radial decreased, and ones in the direction of parallel to the fiber axes increased

    分子動力學模擬結果表明， （ 1 ）界面相內部無定形碳部分微結構無明顯變化，石墨片層部分沿纖維軸向滑移； （ 2 ）界面相模量發生變化，界面相區域各部分的體積彈性模量降低，無定形碳部分及石墨片層部分垂直於纖維軸向的楊氏模量降低，平行於纖維軸向的楊氏模量升高。
  6. The main contents that are researched in the thesis are : asphalt mixture low temperature crazing principle, the influencing factor of asphalt mixtures low temperature crazing, asphalt - rubber macadam, the pressure - resistance intensity, the crazing high temperature, the smooth - resistance and construction technology, the technological economical compare and so on, exploring the new - type structural combinations of asphalt pavement

    本文研究的主要內容是：瀝青混合料低溫開裂機理，瀝青混合料低溫開裂影響因素，瀝青橡膠碎石，玻璃纖維瀝青碎石的高溫抗壓強度，低溫劈裂強度，抗滑性能及其施工工藝，技術與經濟比較等，探索新型的瀝青路面結構組合。
  7. First, polytetrafluoroethylene ( ptfe ) composites filled with various contents of glass fibers ( gf ) and graphite were prepared by compression molding. the screening friction and wear tests were carried out in a reciprocating sliding tribotester. it is found that the optimal ptfe composite was a ptfe - 25wt. % gf - 5wt. % graphite amongst the composites

    採用石墨與短玻璃纖維（ sgf ）填充ptfe ，制備出一系列ptfe復合材料，在往復式滑動摩擦試驗機進行篩選試驗，結果發現: ptfe - 25 % sgf - 5 %石墨復合材料的摩擦系數與比磨損率都比較低。
  8. 406 is non - asbestos clutch facing which adopts refined glass fiber, high - temperature resistance composite fiber materials, high quality metals such as soft copper and so on, uses imported wear and lubrication materials, high grade heat resistance resin binder through special process

    406無石棉離合器面片，採用精製玻纖，耐高溫復合化纖材料，優質軟金屬銅等，選用進口耐磨材料，潤滑材料，高檔耐溫樹脂經過特殊工藝復合粘結而成
  9. 405 is non - asbestos clutch facing which adopts refined glass fiber, high - temperature resistance composite fiber materials, high quality metals such as soft copper and so on, uses imported wear and lubrication materials, high grade heat resistance resin binder through special process

    405無石棉離合器面片，採用精製玻纖，耐高溫復合化纖材料，優質軟金屬銅等，選用進口耐磨材料，潤滑材料，高檔耐溫樹脂經過特殊工藝復合粘結而成
  10. The frictional loss of modified uhmwpe was studied through adding fillers, such as microfine glass bead, mos2 ， talc, glass fibre, carbon fibre and ptfe

    通過填料，如超細玻璃微珠、二硫化鉬、滑石粉、玻璃纖維、碳纖維、聚四氟乙烯，對改性后的超高分子量聚乙烯的摩擦磨損進行研究。
  11. The absorbing oil nature of carbon black, the lubricated effect of graphite and the bad dispersion of carbon fiber limit their application in ecac respectively

    炭黑的吸油性、石墨的潤滑性及碳纖維的分散性分別限制其在導電瀝青混凝土的應用。
  12. ( 6 ) the study of electroplating ni ~ co coating on silica fiber showed that a special pretreatment must be preformed before electroless nickel because of the smooth surface of silica fiber. ( 7 ) a ni - co coating was acquired by means of eletroless and electroplating

    （ 6 ）石英光纖表面電沉積ni - co合金鍍層的研究表明，石英光纖化學性質穩定，表面光滑，化學鍍前必須經過特殊的預處理工藝：脫脂，粗化，敏化，活化，烤烘等。
  13. ( 4 ) compared with other fillers, the performances of wollastonite filling composite system are super to that of calcium carbonate and talcum filling systems, and are near to that of asbestos and glass fiber filling systems

    （ 4 ）與其它pp填充礦物相比，硅灰石填充復合體系的綜合力學性能優于碳酸鈣和滑石的填充體系，並可與石棉、玻璃纖維的填充體系相媲美。
分享友人
分享到 Line

分享到臉書