纖維潤滑劑 的英文怎麼說

中文拼音 [xiānwéirùngǔjì]
纖維潤滑劑 英文
fibre lubricant
  • 纖 : 纖形容詞（細小） fine; minute
  • 維 : Ⅰ動詞1 （連接） tie up; hold together; link 2 （保持; 保全） maintain; safeguard; preserve; keep ...
  • 潤 : Ⅰ形容詞（細膩光滑; 滋潤） moist; smooth; sleek Ⅱ動詞1 （加油或水 使不幹枯） moisten; lubricate 2 ...
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  • 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
  • 纖維 : fibre; staple; filamentary
  • 潤滑劑 : lubricant; unguent; lube; emollient潤滑劑添加劑 lubricant additive
  • 潤滑 : [機械工程] lubricating; lubrication; lubricate
  1. Formulations of fiber lubricants are in general multicomponent systems comprising at least one lubricant and one antistatic component.

    纖維潤滑劑一般為多組分組成，其中至少包含一種潤滑劑和一種抗靜電劑成分。
  2. Taking the brown alumina powder and french chalk as the refractory, the silicasol and dextrin as the composite binder, the western bentonite and sodium carboxymethyl cellulose ( cmc ) as the composite suspension agent, the optimum mixing ratio of the water - based coating was established by the method of orthogonal experiments

    摘要選用棕剛玉粉及滑石粉為耐火填料，以硅溶膠及糊精為復合粘結劑，以鈉基膨潤土和羧甲基纖維素鈉（ cmc ）為復合懸浮劑，通過正交試驗方法確定了最佳配方。
  3. In the dissertation high - temperature corundum honeycombed ceramic regenerative body was prepared by an extrusion process, a - al2o3 minute powder as main raw material, clay, cmc etc as plasticizers, tung oil etc as lubricator. the plastic performance was tested on a plastic measure apparatus

    以a - al _ 2o _ 3微粉料為主原料，採用粘土、羧甲基纖維素（ cmc ）等有機-無機復合增塑劑，加入桐油等作為潤滑劑，採用擠出成型法制備剛玉質高溫型蜂窩陶瓷蓄熱體。
  4. The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine

    用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。
  5. After looking up a large amount of native and foreign information, the materials used in the experiment were as follows : ptfe base, graphite filler, molybdenum disulfide filler, copper powder filler, carbon fiber and so on. the experimental method is that the formula was designed according to uniform experimental method, the relationship between formula and frictional property was found with spline function and then the representative test points were chosen from fitting curve to make verification test for optimization. the preparative technique of solid lubricant is cold - press sintering method

    經過查閱大量國內外文獻資料后確定原料為：聚四氟乙烯樹脂為基體，加入石墨、二硫化鉬、銅粉、碳纖維等填料；試驗方法為：根據均勻試驗方法設計配方，用樣條函數找出配方與摩擦性能的關系，然後在擬合曲線上選取具有代表性的試驗點進行驗證試驗，達到優化的目的；制備工藝：冷壓燒結法制備固體潤滑劑。
  6. The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film

    試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。
  7. Flocculent by high - intensity artificial synthetic high - purity dispersions, special sealants, lubricants

    由高強度絮狀人工合成纖維高純度分散體、特種密封劑、潤滑劑。
  8. Standard test method for determination of phenolic antioxidants and erucamide slip additives in polypropylene homopolymer formulations using liquid chromatography

    用液相色譜法對聚丙烯均聚物配方中酚醛抗氧化劑和酰胺纖維潤滑添加劑測定的標準試驗方法
  9. This filler 1. 40 aramid fibers using high - intensity, highly complex thermal conductivity of carbon fiber, stains and lubricants, made by weaving rope or ring seal products

    此填料四角採用高強度芳綸纖維，復合導熱性極強的碳纖維，污漬及潤滑劑，經編織製成繩狀或環狀密封產品。
  10. Injection - like soft filler used special import high - strength fibers, special lubricants and sealants, according to the strict production of synthetic milky white muddy packing

    注射式軟填料採用進口高強度特種纖維、特種潤滑劑和密封劑，按嚴格工藝合成生產的乳白色泥狀填料。
  11. Air dry the chain and then flex it to break any bonds the lube may have created between contacting surfaces

    風干鏈條（可能是種特殊的物質，肯定不是金屬，應該是植物纖維之類的東西）再彎曲折斷任何聯結，則在接觸面之間可能產生潤滑劑。
分享友人
分享到 Line

分享到臉書