缺陷鑄件 的英文怎麼說

中文拼音 [quēxiànzhùjiàn]
缺陷鑄件 英文
faulty casting
  • 缺 : Ⅰ動詞1 （缺乏; 短少） be short of; lack 2 （殘缺） be missing; be incomplete 3 （該到而未到） be ...
  • 陷 : Ⅰ名詞1 （陷阱） pitfall; trap2 （缺點） defect; deficiency Ⅱ動詞1 （掉進） get stuck or bogged do...
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 缺陷 : defect; fault; faultiness; vitium; lesion; flaw; disorder; imperfection; drawback; blemish
  1. Third, on the base of expatiating on experimental research method and theoretical research method of joints, the paper points out two kinds of valid methods, which are used to analyze the tube joints stress of dendriform structure by making use of semi - analytical method and inelastic large deflection finite element analysis method, confirms to apply the evaporative pattern casting process as the facture method of dendriform structure cast joints, and detailed dissertates the casting theory, casting process, generation cause and prevention measure of casting flaws, heat treatment method and inspection standard about cast steel joints

    然後在闡述樹狀結構節點實驗研究方法和理論研究方法的基礎上，提出了利用半解析法和彈塑性大撓度有限元法兩種有效分析樹狀結構管節點應力的方法，並給出兩種方法的詳細表達式及它們各自的優缺點。通過對鑄鋼件常見製作方法的介紹，確定了採用消失模法作為樹狀結構鑄鋼節點的製作方法，並詳細論述了用消失模法製作鑄鋼節點的鑄造原理、鑄造工藝、鑄造缺陷產生的原因及防治措施、鑄鋼節點的熱處理方法以及檢驗標準。
  2. The quality of furan sand castings is usually better than clay sand castings, however, some defects are also very easy take place with furan sand castings such as blow hole, metal penetration, veining, cracking, slag inclusion, hardness too low, surface recarburation, surface sulphuration, nodularity degeneration etc, which were usually caused by improper raw materials selection, improper method design, incorrect moulding or / and core - making

    摘要呋喃樹脂砂鑄件質量一般比黏土砂鑄件好，但如果原材料選擇、工藝設計、造型和制芯操作不當，也會產生氣孔、粘砂、脈紋、裂紋，夾渣、硬度不足、滲碳、滲硫和球化不良等鑄造缺陷。
  3. Shrinkage / porosity is a common defect in castings and one of main causes making products waste

    縮孔縮松是鑄件常見的缺陷，是產生廢品的主要原因之一。
  4. The reasons causing common defects of evaporating pattern castings and the measures to prevent defects were described in detail

    詳細敘述消失模鑄件常見缺陷的產生原因和防止方法。
  5. The metal laser fuse fill in the application of metal wear, co - mosion, broken, blfida, glass, chromium scar, casting error, pro - cessing ultra poor, leakage repairs ; mechanical parts of the modified surface to be cut moldova, and wear - resisting, cor - rosion resistance, withetand high temperatures and perfor - mance

    該金屬激光熔補機適用於各種金屬磨損、腐蝕、斷、裂、劃傷、鉻痕、鑄造缺陷、泄漏的修復；對各種機械零配件表面的改性，使其具有減摩、耐磨、耐腐蝕、耐高溫等性能。
  6. Terminology of internal defects in castings as revealed by radiography

    輻射攝影術揭示的鑄件內部缺陷詞匯
  7. Based on the mechanism of hot cracking formation of castings, the cracking defects of furnace door frame castings was analyzed, and found that the main reasons causing cracking are as follows : construction of the casting was not reasonable, gating system was not proper, and pouring temperature was too high

    摘要根據鑄件產生熱裂紋的機理，對爐門框裂紋缺陷進行分析，找到了裂紋產生的主要原因是鑄件結構和澆注系統不合理，以及澆注溫度過高。
  8. Internal combustion engines. welding repair for gray iron casting defecfs. specifications

    內燃機.灰鐵鑄件缺陷焊補.技術條件
  9. Upgrading of castings to meet x - ray quality needs relies on the grinding out of faulty areas, weld repairs, heat treatment, and retest and examination

    鑄件的改進要滿足x射線質量的要求就要靠缺陷部位的磨削，焊補，熱處理和重復測試和檢驗。
  10. Founding - visual examination of surface discontinuities - steel sand castings ; german version en 12454 : 1998

    鑄造.表面缺陷的目視檢驗.鋼砂型鑄件
  11. Dispersed shrinkage is the main reason causing leakage of multi - cylinder heads of diesel engines

    摘要縮松缺陷是導致多缸柴油機缸蓋鑄件滲漏的主要原因。
  12. The ultimate aim of the numerical simulation on temperature field in castings solidification process is for eliminating shrinkage / porosity or limiting them within the user ' s permission

    鑄件凝固過程溫度場數值模擬為最終消除縮孔縮松缺陷或將其限制在用戶允許的范圍內，以獲得質量合格的產品提供了非常有效的手段。
  13. Analysis results of histogram statistics and section electron microscopic scan technique, are that fracture feature of the cracks of the hbbb is similar and the crack is multi - source strain fatigue one. internal defects of the cast, such as impurities, gas holes, etc, are the main causes for early cracks. the contrast analysis of static strength, model and transient respond on three structures with fem proves that geometrical stress concentration in partial area has influence on early crack, also

    利用直方圖等統計方法和電鏡掃描技術對該抱軸箱體裂紋分析的結果是：抱軸箱體的裂紋斷口特徵相近，裂紋性質屬于多源性低周疲勞裂紋，鑄件中的夾雜、氣孔等內部缺陷是導致過早裂損的主要原因；利用有限元法對該抱軸箱體三種結構的靜強度、模態和動態響應對比分析，證實了局部幾何性應力集中對過早裂損也有一定影響。
  14. Abstract : using furan sand to produce heavy diesel engine block and crankshaft eliminated defects of castings including “ penetration / burn - in ”, “ shrinkage porosity ”, “ big dimension deviation ” of cylinder block, “ penetration / bum - in ”, “ misrun ” and “ run - out ” of crankshaft, and so on

    文摘:樹脂砂鑄造工藝應用於大型球墨鑄鐵件整體鑄造柴油機缸體、曲軸生產上消除整鑄缸體「粘砂」 、 「縮松」 、 「尺寸偏差大」及曲軸「粘砂」 、 「澆不足」 、 「漏鐵液」等鑄造缺陷，具有明顯的效果。
  15. Abstract : some kinds of defects in plate castings of gray cast iron are discussed, and varies kinds of gating systems and their advantages or disadvantages are analysed in this articles

    文摘:本文介紹了平板類灰鑄鐵件易產生的各類鑄造缺陷及其在生產中常用的各種澆注系統，並分析了各類澆注系統的優缺點。
  16. The defect of crack in the engine block of 8170 diesel engine has beem researched and analyzed, which can be solved and avoided through the following measures : optimizing the structure of engine block casting, improving alloying technology, perfecting pouring process and adopting normal inoculation before furnace and metal - stream inoculation during the period of pouring

    摘要對8170缸體裂紋缺陷進行了探討分析，通過優化鑄件結構，改進合金化工藝，完善澆注工藝以及隨流孕育與爐前孕育工藝相結合等措施，使裂紋缺陷解決。
  17. A new electroforming technique, numerical control jet electroforming, was proposed, it not only can solve some problem of tradition electroforming but also can make nano metal block and metal accessory, and the elemental research on the new technique was carried out

    本文提出了一種新的電鑄工藝方案? ?數控噴射電鑄，不但能解決傳統電鑄的一些缺陷，而且可以制備納米金屬塊體和金屬零件，並通過理論分析和試驗對該工藝進行了基礎性研究。
  18. The subsystem of the casting foresee and analysis established the mathematical model of the quantitative linear regression analysis for the compacted graphite cast iron defects. it provided guarantee for predication and control of casting defective index within permissive ranges

    鑄件質量分析及預測子系統建立了蠕墨鑄鐵件缺陷定量分析的線性回歸分析數學模型，為預測及控制缺陷廢品率在規定范圍內提供保證。
  19. Methods of liquid penetrant testing and classification of indication for steel castings

    鑄鋼件滲透探傷及缺陷顯示跡痕的評級方法
  20. Low heat dilating rate : it is just this characteristic that make the foundry more precisely, less cracking and high output

    熱膨脹率低：熱膨脹率之低與鉻礦砂等特殊砂相同，所以，生產鑄件的尺寸精度高，破裂及表面缺陷少，鑄件成品率高。
分享友人
分享到 Line

分享到臉書