翹曲 的英文怎麼說

中文拼音 [qiáoqū]
翹曲 英文
buckling; warping; bow and twist
  • 翹 : 翹動詞（一頭向上仰起） stick [hold] up ; bend [turn] upwards; curl up
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  1. Bedrock beneath hebgen lake warped and rotated, causing a seiche in the lake.

    赫布根湖底的基巖發生了翹曲和旋轉，引起湖中浪涌。
  2. Simulation analysis of the lengthways warp of truck carling outside board

    卡車縱梁外板縱向翹曲的模擬分析
  3. Based on the three new supposition and the tow new mechanical tools : moment vector and radius vector, the warping theory introduced the analytical method of the rotation of a cross section around a fixed axis, so as to make the space stability of the thin - walled member complanate and one - dimensioned

    翹曲理論以三條新的假定和新建立的彎矩矢量和轉角向徑兩大力學工具為基礎，提出了繞定軸轉動的分析方法，使薄壁構件的空間變形平面化、一維化。
  4. Sagging and creep of the compo ? nents occur during heat treatment as a result of improper support of components or warped hearth in the hardening furnace

    當對部件支持不當或在爐床翹曲的淬火爐中進行淬火時，部件在熱處理過程中會出現弧垂和蠕變現象。
  5. In eq. (53)it is assumed that there is no restraint to the free warping of the cross sections.

    在式（53）中，可假定對截面的自由翹曲沒有阻礙。
  6. The deeper structure appears to be a gently warped monocline.

    較深構造彷彿是輕度翹曲的單斜。
  7. Gramophone records warp in very hot weather

    在非常熱的天氣時，唱片會翹曲。
  8. Twisting arises in boards through the presence of spiral or interlocking grain.

    翹曲多發生在螺旋或交錯紋理的板材中。
  9. Tilting, warping, and changes in elevation can seriously affect canals and shoreline facilities of various kinks.

    傾斜、翹曲和高程變化可以嚴重地影響水渠和各種岸邊設備。
  10. Although aircraft designers and engineers continued to employ wing - warping techniques for years afterward ( especially on early monoplanes such as the bleriot xi ), ever faster flight speeds eventually led them to beef up wing structures to resist the resulting stresses

    雖然其後許多年間，飛機設計師和工程師仍繼續採用翹曲機翼設計（尤其是布雷修xi型等早期單翼機） ，但由於飛行速度不斷提升，終于迫使他們加強機翼結構，以承擔所增加的應力。
  11. Method to flatten pcb by warp twist tool plates

    印製電路板翹曲弓形的模具整平法
  12. It was found that nitrogen increased the fracture strength of silicon single crystal. we consider that the nitrogen may change the shockley band on silicon surface and form complex to influence the fracture procedure

    本文從硅材料的基本概念入手，闡述了硅單晶材料的脆性斷裂、脆塑轉變以及在熱處理過程中的翹曲研究，並通過這三個部分進行實驗。
  13. This effects called warping.

    此種效應稱為翹曲。
  14. Analytical and fem simulation of the front end bending in asymmetrical hot plate rolling

    非對稱板帶熱軋頭部翹曲的分析與有限元模擬
  15. The link should be formed steel plate, plate edge, no burr hole ; a joint warping, used to be calibrated to prevent injury and friction, the friction surface to ensure close

    連接處的鋼板或型鋼應平整，板邊、孔邊無毛刺；接頭處有翹曲、變形必須進行校正，並防止損傷摩擦面，保證摩擦面緊貼。
  16. Abstract : thermally induced stress and the relevant warpage cause by inappropriate mold design and processing conditions are problems that confounded the overall success of injection molding. a thermorheologically simple thermoviscoelastic two - dimension material model is used to simulate the residual stress and warpage within injection molded parts generated during the cooling stage of the injection molding cycle. the initial temperature field corresponds to the end of the filling stage. the fully time - dependent algorithm is based on the calculation of the elastic response at every time step. numerical results are discussed with respect to temperature and pressure

    文摘:不均勻的熱殘余應力及其變形是注塑成型加工中常見的工程問題之一.應用熱流變簡單材料的二維熱粘彈本構方程得到的遞推公式，數值模擬了成型中的熱殘余應力及其翹曲變形，並用數值實驗討論了溫度、壓力對注塑件殘余應力及變形的影響，發現溫度變化不均勻是注塑件翹曲變形的最主要原因，其影響遠大於壓力的作用，與工程實驗的結論一致
  17. In dvd focus servo system, the warp of the disc induces periodic disturbance whose frequency is same as the rotation frequency of the disc

    摘要在dvd聚焦伺服系統中，光盤翹曲會導致產生與光盤轉動頻率相同的周期性擾動。
  18. Test methods of platness for printed boards

    印製板翹曲度測試方法
  19. Test method for measuring warp on silicon slices by nontact scanning

    矽片翹曲度非接觸式測試方法
  20. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
分享友人
分享到 Line

分享到臉書