耐壓強度 的英文怎麼說

中文拼音 [nàiyāqiángdù]
耐壓強度 英文
compression strength
  • 耐 : 動詞（受得住; 禁得起） be able to bear or endure
  • 壓 : 壓構詞成分。
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. Results show that : ( 1 ) for each particle size of andalusite, variation tendency of the properties of the material is generally the same : the maximum of bulk density, compressive strength and rupture strength appears in the range of 5 % - 10 % content of fiber, these properties of the material remarkably decrease as the fiber content exceed 10 % ; while at the same fiber content, the properties of the material increase with the increase of firing temperature

    結果表明： （ 1 ）對于不同粒度的原料，性能變化規律大致相同：在同一燒成溫度下，體積密度、常溫耐壓強度、常溫抗折強度在5 10之間出現峰值，加入量超過10之後材料的性能明顯下降；在相同的纖維含量下，隨著燒成溫度的提高，試樣的各項性能均有所上升。
  2. Carbon materials - determination of the compressive strength

    炭素材料耐壓強度測定方法
  3. When the alumina fiber accounted for 10 %, the density of the composites was chiefly high and the fiber evulsion effect was reinforced ; when the alumina fiber accounted for 30 %, the fiber evulsion effect, fracture and bridge - connection effect were mainly strengthened, when the fiber proportion was 50 %, at the temperature of 1500 c, the bending strength reached 26. 11 mpa while the compressive strength was 79. 30 mpa

    氧化鋁纖維含量為10和30的試樣增強機理不同，含量為10時，復合材料以基質密實度高、纖維拔出效應增強為主；氧化鋁纖維含量為30時，復合材料以纖維拔出、斷裂、橋聯效應增強為主。當纖維含量為50時，在1500下燒成，其抗折強度達到26 . 11mpa ，耐壓強度達到79 . 30mpa ，該復合材料可用作輕質保溫材料。
  4. The influence of burning system on the properties and structure of the ceramic capacitors has been studied under the certain temperature system, the optimum sintering temperature of the ceramics was primarily decided by the content of bi2o3 ? 3tio2. the sintering temperature dropped with the adding of bi2o3 ? 3tio2. at the range of suitable sintering temperature, slow heating and low temperature sintering can obtain fine grain and dense structure. it results in the improving of the breakdown voltage for the middle - high voltage ceramic capacitors

    研究了燒成工藝制度對電容器陶瓷性能和結構的影響，結果表明：在一定的升溫保溫時間下，瓷料的最佳燒結溫度主要取決于組成中bi _ 2o _ 3 ? 3tio _ 2的含量， bi _ 2o _ 3 ? 3tio _ 2含量的增加將降低燒結溫度；在合理的燒結溫度范圍內，慢速升溫和低溫燒結將有利於得到細晶緻密結構，從而改善中高壓陶瓷電容器的耐壓強度。
  5. Abstract : this article is about two series of borate and phosphate comprising seven directions. the experiment result shows that both of the two gl ass antioxidants can reduce apparent porosity ， raise oxidation resistance and th e crushing strenth after fire ， but lower refractoriness under load. phosphate glas s is superior to borate in refractoriness under load. which c an attain over 1600 ; so the phosphate glass is a d esirable antioxidant

    文摘:研究了硼酸鹽和磷酸鹽兩個系列七種配方的玻璃防氧化劑，實驗表明這兩種玻璃防氧化劑均可降低鋁鎂碳磚的氣孔率，提高鋁鎂碳磚的抗氧化能力及燒后的耐壓強度，但也不同程度地降低了鋁鎂磚的高溫荷重軟化變形溫度，其中磷酸鹽玻璃優于硼酸鹽玻璃，其高溫荷重軟化變形溫度可達到1600以上，仍是可取的防氧化劑
  6. 2 softening point under load 1450

    1耐壓強度2荷重軟化溫度
  7. The results show that : the fillers of sio2 based investment consist of sio2, al2o3 and mgo, and the binder is nh4h2po4 for sio2 based investment, the bulk density and the compression strength decrease, the apparent porosity and the thermal expansion increase, when the specimens are heated to 900 ; the fillers of al2o3 based investment consist of al2o3 and mgo, and the binder is nh4h2po4 ; for al2o3 based investment, the bulk density decreases and the apparent porosity increases when the specimens are heated to 900 ; the fillers of mgo based investment consist of mgo and al2o3, and the binder is ca cement ; for mgo based investment, the compression strength decreases and the thermal expansion increases greatly when the specimens are heated to 900

    結果表明：氧化硅系包埋料的骨料是氧化硅、氧化鋁、氧化鎂，結合劑為磷酸二氫銨，其900鍛燒后顯氣孔率增加，體積密度下降，耐壓強度降低，熱膨脹增大；氧化鋁系包埋料的骨料是氧化鋁和氧化鎂，結合劑為磷酸二氫銨，其900燒后顯氣孔率增加，體積密度下降，熱膨脹變化不大；氧化鎂系包埋料的骨料是氧化鎂和氧化鋁，結合劑是鋁酸鈣水泥，其900燒后耐壓強度明顯降低，熱膨脹明顯增大。
  8. Very high compression strength and excellent machining performance

    耐壓強度高及優良的機加工性能。
  9. This type of joint have been widelu used in the steel pipeline system for connection, it has a very good self - compensation performance while temperature change and angle deviation of the pipeline axis

    鍛壓卡箍式柔性管道接頭該產品具有溫度自補償和角度自補償功能，是鋼制管道系統中廣泛應用的聯接件，其結構合理、耐壓強度高、密封性能好，安裝維修方便。
  10. It has good abrasion resistance, corrosion resistance, thermal shock resistance and high crushing strength, good, slag corrosion resistance, and is suitable for the zone which need good abrasion resistance in boilers

    該材料抗腐蝕性強、耐壓強度高、熱震穩定性好、耐磨性小、抗剝落，是鍋爐易磨損部位的最佳材料。
  11. The experiment showed that the temperatures and the fiber proportions influenced great on the compressive strength, bending strength, volume density and the porosity of the composites

    實驗結果表明，燒成溫度和纖維含量對復合材料的耐壓強度、抗折強度、體積密度和氣孔率影響較大。
  12. We tested the ambient temperature compressive strength, the ambient temperature bending strength, volume density and the porosity of the sintered composites. by means of the om, sem, and x - ray, we analyzed the composites micro - structure ; we studied the dispersion methods & the mechanism of damage of the fiber ; we also did research on the reinforced mechanism and the fabrication characteristics of the fcmc

    測試燒后試樣的常溫耐壓強度、常溫抗折強度、體積密度、氣孔率，並藉助于光學顯微鏡、掃描電鏡以及x射線衍射圖象對復合材料微觀結構進行了分析，探討了復合材料中纖維的分散方法、纖維的損傷機理、纖維增強al _ 2o _ 3復合材料的增強機理和及制備特性。
  13. 1 testing method for crushing strength and modulus of rupture of castable refractories amendment 1

    可鑄耐火材料斷裂模數和耐壓強度的試驗方法
  14. Qj series amorphous refractory developed by this factory is series insulation castable, which has such advantages as high refractoriness, high crushing strength and small thermal conductivity. this series product is used widely as insultion material for various heating furnace, atmospheric and vacuum furnace and sulfur recovery device in petrocnemical industry

    Qj系列不定形耐火材料是我廠自行研製的系列保溫隔熱澆注料，它具有耐火度高，耐壓強度高，導熱系數小等特點，該系列產品廣泛應用於石油化工各類加熱爐，常減壓爐，硫回收裝置等工業窯爐作保溫熱材料。
  15. Methods of testing insulating varnishes. determination of electric strength

    絕緣清漆試驗方法.耐壓強度測定
  16. High withstanding pressure, long service life

    耐壓強度高、使用壽命更長。
  17. 1 testing method for cold crushing strength of refractory bricks amendment 1

    耐火磚低溫耐壓強度的試驗方法
  18. Shaped insulating refractory products - determination of cold crushing strength

    定形隔熱耐火製品常溫耐壓強度試驗方法
  19. Concentrations, bore flow rate, dope solution temperature, coagulant bath temperature, 5 types of composite pu hollow fiber membranes were prepared. the recovery extent of different composition hollow fiber membrane pore size is different. the ability to recover of type

    另外，在pu紡絲液中混入適量醋酸纖維素（ ca ） ，也可有效改善pu溶液的可紡性，提高pu中空纖維膜的支撐強度和耐壓強度，但壓力響應性有所減弱。
  20. Dense, shaped refractory products - determination of cold compressive strength - part 1 : referee test without packing

    緻密定形耐火製品常溫耐壓強度試驗方法無襯墊仲裁試驗
分享友人
分享到 Line

分享到臉書