脈弧 的英文怎麼說

中文拼音 [màihú]
脈弧 英文
haemal arch
  • 脈 : 脈名詞1. （動脈和靜脈的統稱） arteries and veins2. （脈搏的簡稱） pulse 3. （像血管的組織; 連貫成系統的東西） vein
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  1. Scm control system of pulse plasma arc welding

    脈沖等離子弧焊接的單片機控制系統
  2. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  3. If infection of v. vulnificus is strongly suspected, early diagnosis with broad spectrum intravenous antibiotics and surgical excision of devitalized tissues are essential to decrease morbidity and mortality

    因為創傷弧菌感染導致敗血癥合併壞死性筋膜炎的死亡率非常高，所以如果強烈懷疑創傷弧菌感染時，早期診斷及合併使用靜脈注射廣效性抗生素和外科切除壞死組織可以減少罹病率及死亡率。
  4. A two - dimensional plain strain finite element model of infinite plate is developed to investigate the ultrasonic wave propagation and scattering on three kinds of cracks : parallel to the surface, 450 oblique angle to the surface, and quarter - circle

    摘要建立了無限長板的具有吸收邊界的二維平面應變有限元模型，在研究了脈沖超聲波在無限長板中傳播的基礎上，對板中平行於表面的裂紋、與表面成45的斜裂紋和四分之一圓周弧形裂紋三種情況的脈沖超聲波散射進行了重點研究。
  5. Three welding modes ： dc pulsed tig, dc mma

    集直流氬弧焊，脈沖氬弧焊，直流手工焊於一體。
  6. Multiple functions available ： start / crater arc current, increase / decrease time, base / crest value current, pulse frequency, pulse rate, post flow time, hf welding

    功能豐富：起始/收弧電流、上升/下降時間、基值電流、峰直電流、脈沖頻率、占空比、滯后關氣時間分別可調，高頻引弧。
  7. Multiple funcyions available : start / crater arc current, increase / decrease time, base, crest value current, pulse frequency, pulse rate, post flow time, hf / friction welding, water / gas cooling

    功能豐富：起始/收弧電流、上升/下降時間、基值電流、峰值電流、脈沖頻率、占空比、滯后關氣時間分別可調，高頻/接觸引弧、水冷/氣冷可供選用。
  8. Surface modification of h13 steel by arc deposition of al film and high current pulsed electron bombardment

    13鋼電弧沉積鋁膜及強流脈沖電子束后處理的復合改性研究
  9. Interpretation signs : graphic signs in the green arc on behalf of the sense of the times and dynamic range

    標志釋意：標志圖形中的綠色動感弧線代表時代感和山脈。
  10. Experiments and applications of pulse submerge arc welding technique in jointing membrane water - walls

    脈沖埋弧焊技術在膜式水冷壁管屏拼接中的試驗及應用
  11. The tooth shape of gear pump has important influence on machining and characteristics of pumps, such as flow rate, fluctuation rate and noise etc. first, the working principle of tatsuno combined pumps is analyzed in this article

    齒輪泵的齒形對泵的加工、性能（如：流量、脈動率、噪聲）等有很大的影響。本文首先分析了進口tatsuno組合泵的工作原理，並進一步分析了其採用一對雙圓弧齒輪的優缺點。
  12. Although the flux per revolution of the optimized pumps is a little smaller than that of tatsuno combined pumps, other characteristics, such as fluctuation rate, maximum pressure angle and velocity fluctuation rate etc, are much better. the methods to cut gears are proposed in the theory for the practical produce in the future

    雖然，在體積相等的條件下，優化出來的外圓弧包絡線內嚙合齒輪泵的排量略小於tatsuno組合泵的排量，但其它性能（如：流量脈動率、最大壓力角、速度波動量）都更優。
  13. Influence of negative pulse on aluminum alloy micro - arc oxidation

    負脈沖對鋁合金微弧氧化的影響
  14. 4 the research, development and production of surface engineering - new plating techniques ; electroless plating, composite electroplating ; aluminium and its alloys hard anodizing and colouring, metal surface ceramics and the surface modification of special nonmetal materials

    鋁合金表面微弧氧化自潤滑陶瓷覆層新技術電沉積或脈沖電沉積制備多功能復合材料新技術無氰電鍍鋅-鋁合金和鋅-鈰合金新工藝
  15. A comparison of the flows with different gate - opening rates shows the causes that opening the gate at a higher rate is favorable to the reduction of cavitation, gate vibration as well as the gate load fluctuation. in addition, a study has been made to show the influence of the high - speed jet flow coming downward from the narrow gate gap on the flow condition in the tunnel downstream to the gate

    通過分析比較不同閥門開啟速率對流動特性的影響，闡明了快速開啟閥門不僅有利於減少空化空蝕也有利於減小弧門振動和啟門力的脈動，此外，研究了門楣處狹窄縫隙高速射流對門后流態、壓力脈動和弧門受力等方面的影響。
  16. A novel current control mode pulse width modulation switched high frequency resonant arc igniting device is developed based on uc3842 and the principle is analyzed

    摘要採用uc3842設計了電流控制型脈寬調制開關式高頻振蕩引弧器，並對其工作原理進行了分析。
  17. The variable polarity power supply circuit uses two stages full - bridge inverter, the former inverter is regarded as a constant - current source with fast dynamic response, and supplys energy for the second one, and the latter one is to produce variable polarity current excellently, and low - frequency pulse current by variable polarity power supply is used to reduce input energy and control the shape of weld bead while welding. a series of high - frequency pulse current is superposed on direct - current - electrode - negative ( dcen ) current through the high - frequency pulse power supply, which is used to compress the arc and improve process of crystallization

    其中變極性電源採用二次全橋逆變結構，一次逆變提供快速的響應速率並給二次逆變提供能量，二次逆變提供良好的變極性性能，使輸出能量最優化，並用其低頻電流特性減小電弧線能量，控制焊縫成形;高頻脈沖電源提供的高頻電流疊加在反極性電流dcen上，利用電流的高頻特性壓縮電弧，改善焊縫金屬結晶過程。
  18. In this thesis, a high - frequency variable polarity arc welding power supply was investigated, which consisted of two independent power sources, the variable polarity power supply and the high - frequency pulse one, having advantages both of them

    本文針對鋁合金焊接研製了一種新型電源，所研究的高頻變極性弧焊電源採用雙電源結構，由變極性電源和高頻脈沖電源組成，綜合了兩者的優點。
  19. Some new phenomenons were discovered. the width of trigger current changes with the discharge condition, it is only 100u. s when let the trigger source work alone, but it can rise up to 300us with the arc current and magnetic field

    在研究過程中發現引弧電流脈沖寬度受放電狀態的影響很大，在不引燃主弧時脈寬只有75 s ，而在引燃主弧並在加磁場的情況下會增大到300 s 。
  20. The dcep mig has the characteristic of deeper penetration which can reduce defective fusion and good arc stabilization. the dcen mig has the characteristic of shallow penetration of welding seam, and the welding wire has a high melting speed. so the variable polarity pulsed mig is a new technology for the welding of aluminium alloy sheet

    變極性脈沖mig焊是一種新的焊接工藝方法，其綜合了dcep脈沖mig焊熔深較大、可以減少焊縫的熔合不良、電弧穩定性好和dcenmig焊焊縫熔深淺、焊絲熔化速度較快的特點，減小了焊縫的熔深，增加了焊絲的熔化速度，是一種適合於薄板鋁合金焊接的新方法。
分享友人
分享到 Line

分享到臉書