脫坯 的英文怎麼說

中文拼音 [tuōpī]
脫坯 英文
mould adobe blocks
  • 脫 : Ⅰ動詞1 （脫落） cast; shed; drop; fall off 2 （取下; 除去） take off; strip; cast off 3 （脫離） ...
  • 坯 : 名詞1 （未經燒制的磚、瓦、瓷等的製品） base 2 （土坯） unburnt brick; earthen brick; adobe 3 [方...
  1. In order to consolidate the powder compacts into densified billets, the technique of vacuum degassing, encapsulating and warm pressing was adopted

    提出了ti / al復合粉的制坯緻密和真空脫氣包套工藝。
  2. The hearth pressure, pipeline pressure and heat exchanger are protected and the important parameters are sent to the factory - level mis network. so far, with the said system, the purpose to improve the control accuracy and bloom heating quality, to

    系統設計達到了提高控制精度、提高鋼坯加熱質量、減少氧化燒損、減少脫碳層厚度、減少環境污染，節約能源的目的，具有良好的經濟效益和社會效益
  3. The necessity and purpose of the technological revamp is discussed in this paper. the subjects of the revamp are briefly introduced herein, which involve : 1 ) enlarging the desulphurization ability of hot metal to achieve complete desulphurization pretreatment of hot metal ; 2 ) drawing up a general plan and programme for the revamp of the continuous caster and implementing it step by step ; 3 ) building up a straight curved slab continuous casting machine at the begining to meet the requirements for high quality steel

    分析了技術改造的必要性;闡明了技術改造的目的;簡介了技術改造的主要內容，擴大鐵水脫硫能力，實現鐵水全部脫硫預處理，鑄機改造總體規劃設計、分步實施，先改建成一座直弧式板坯鑄機，以適應高質量鋼的要求。
  4. The outer form of the impression is made by the way of the rotary - cutting according to the inner form of the body. the process is that a semi - dry body is coated over the impression, then patting the outer wall of the body evenly, and then demolding

    印模的外形是按坯體內形弧線旋削而成的，將晾至半乾的坯覆在模種上，均勻按拍坯體外壁，然後脫模。
  5. Reaction - bonded sic was prepared by using melt silicon infiltrated carbon perform at 1500 c ; then evaporated the resist silicon at 1800 c for 2h in vacuum and the porous body of sic was attained. using melting mosi2 infiltrated sic body at 2050 c we got the desitive mosi2 / sic composite

    將c質坯體在1500左右制得rbsc （反應燒結sic ）材料，採用真空下1800脫除rbsc中的殘余si的方法，獲得了多孔的sic坯體，用mosi _ 2在2050直接浸滲坯體得到了緻密的mosi _ 2 sic復合材料。
  6. The technique can avoid produce ti / al chemical compound in high temperature. the chemical compound would increase the difficulty of pressing. the research on vacuum degassing and temperature of pressing can acquire the ideal composite powders of highly

    對ti / al復合粉進行真空脫氣及低溫熱壓制可以降低坯料中空氣含量並提高粉末顆粒的界面結合強度，同時避免高溫下生成tial基化合物增加緻密難度，對真空脫氣及壓制溫度進行研究，獲得理想的緻密度極高的復合粉末。
分享友人
分享到 Line

分享到臉書