腐蝕余度 的英文怎麼說

中文拼音 [fǔshíyúdù]
腐蝕余度 英文
corrosion allowance
  • 腐 : Ⅰ名詞（豆腐） bean curdⅡ動詞（腐爛; 變壞） decay Ⅲ形容詞（腐爛） rotten; corroded; putrid
  • 蝕 : Ⅰ動詞1. （損失; 虧耗） lose 2. （腐蝕） erode; corrode Ⅱ名詞（天體現象） eclipse
  • 余 : Ⅰ動詞（剩下） remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 腐蝕 : 1 （通過化學作用使物體逐漸消損破壞） corrode; corrosion; corroding; deep etch; diabrosis; rot; ea...
  1. The reduction factors derived from curve fitting based on calculation results by the finite element program ( ansys ) considering all kinds of damages such as cutouts, corrosion, cracks, denting, initial deflection and residual stress are introduced to modify the effective width of perfect panel in the present paper

    本文考慮板中可能存在孔洞、腐蝕、裂縫、局部撞損和初始焊接變形或殘余應力等損傷和初始缺陷，對不同的損傷形式用有限元程序（ ansys ）進行大量的計算，通過曲線擬合的方法引入折減系數對完好板格的有效寬度進行修正。
  2. Residual stresses not only result in unexpected machining distortion, but also increases the possibility of unpredicted fatigue failures and stress corrosion cracks ( scc )

    殘余應力的存在直接影響構件的疲勞強度、抗應力腐蝕性能及尺寸穩定性，並導致后續機械加工過程中產生變形。
  3. The paper mainly discussed the reasons of stress from liquid ammonia pressure vessel causing crack through examing data and experimental results and analysing relevant referential documents and materials, taking 1200 ammonia vessel ' s crack and leaking in a certain fertilization company as an example : there existed remaining welding, stress in the equipment ; there existed a stress decaying surrounding, i. e., moisture 0. 2 %, and temperature > - 5 with o2 or co2 inside ; the higher the intensity of raw materials, more possible it was to have stress decaying crack

    摘要以某化肥公司1200氨冷器殼體開裂泄漏的失效分析為例，通過對檢驗數據和結果及有關文獻資料的分析研究，探究了液氨介質壓力容器產生應力腐蝕裂紋的原因：設備中存在較高的焊接殘余應力；液氨介質具備應力腐蝕環境，即含水量0 . 2 % ，且有空氣（ o2或co2 ）污染（或摻入） ，使用溫度高於零下5 ；母材強度越高，應力腐蝕裂紋產生的傾向就越大。
  4. The original design was intermediate vapor 42t / h, but the actual output is 30 - 35t / h, at the same time the temperature and pressure of the vapor are unstable, it affects the economic efficiency, the reason were the collecting dust on the heat area and serious corrision, they led to the decrease of the boiler load, and need stop to washing the dust, the article deals with the reform of the exhaust gas boiler, at the basic of the design condition, after thermo calculation, flute gas, resistence calculationand strenth calculation, the structure of the heat surface had been rearranged, then the proof calculation was done

    原設計產中壓蒸汽42噸時，但投運后只產30 - 35噸時，並且蒸汽溫度和壓力均不穩定，影響到經濟效益。其原因是受熱面積灰和腐蝕嚴重，影響傳熱使鍋爐負荷下降，不能長時間運行，需停產清理積灰。本論文針對此余熱鍋爐的技術改造，在給定設計條件基礎上，通過熱力計算，煙氣阻力計算和強度計算，對鍋爐受熱面結構重新布置，然後再作校核計算。
  5. The buckling and ultimate strength of ship plating normally depend on a variety of influential factors, namely geometric / material properties, loading characteristics, initial imperfections ( i. e. initial deflections and residual stresses ), boundary conditions and corrosion, fatigue cracking

    船體板的屈曲和極限強度取決于很多影響因素，主要有：板的幾何尺寸、材料特性、載荷特徵、初始缺陷（如初始變形和焊接殘余應力） 、邊界條件以及腐蝕的影響、疲勞裂紋等。
分享友人
分享到 Line

分享到臉書