膛壓計 的英文怎麼說
中文拼音 [tángyājì]
膛壓計
英文
pressure gage-
The results proved that : ( 1 ) because of the material ' s difference of primer - 9 and primer - 5, the maximum stress of primer - 5 is larger than primer - 9 but the maximum displacement is smaller than primer - 9. ( 2 ) because of the unrenewable shape changing of primer - 9 after impacting by the pin, it will cracking under high pressure more easily. so, the paper give the suggestion that the designer should decrease the depth of impacting by pin in the case of the primer be fired successfully
對底- 9底火、底部被擊針撞擊后的第- 9底火和底- 5底火在膛壓作用下分別進行了有限元數值分析，計算表明： （ 1 ）底- 5底火底部擊針撞擊部位為火帽座，其材料為鋼帶，底- 9底部承受撞擊部位為底火體，其材料為冷拉退火圓鋼，由於材料強度不同，承受壓力能力和變形能力不同：雖然在膛壓作用過程中底- 5底火的最大應力值比底- 9底火的大，但底- 5底火的最大位移量卻比底- 9底火的小得多。By researched and analyzed, it was found that grain fracture had close relation with charge design safety of guns. grain fracture can lead to pressure abnormity in chamber. particularly in the condition of low temperature, it was the main cause leading to chamber blow
經研究分析，火藥顆粒的破碎直接影響到裝藥設計安全性，造成膛壓異常現象，特別在低溫條件下，火藥破碎是引起膛炸的主要原因。The dissertation links with charge design safety of guns and constitutes the theory model of relation between grain fracture and interior ballistic performance. the program which resembles the influence of grain fracture to interior ballistic performance is compiled. the relation between grain fracture and exceptional pressure in chamber is analyzed, and an elementary analysis to the principle of chamber blow is made
本論文是結合火炮裝藥設計安全性的研究課題，通過理論分析和數值模擬的研究手段，建立火藥破碎與內彈道性能關系的理論模型，進行火藥破碎對內彈道性能影響的數值模擬，分析了火藥破碎與膛內異常壓力之間的聯系，並對膛炸機理進行初步分析。( 3 ) through numerical simulation and compution on model of two - phase flow, analysis is done on pressure distributing in the chamber of gun for balance
（ 3 ）應用兩相流彈道模型的模擬計算，對膛內壓力分佈進行分析。This thesis designed and constructed a series of solid circulating loop devices, including cyclone separator, loop seal, external heat exchanger ( ehe ) and correspondent joining pipes. a data acquiring system was completed to realize the data real - time display and record the pressure of the whole system and air flow
設計和搭建了從爐膛頂部出口到底部進口的物料回送裝置，包括旋風分離器，返料器，外置換熱器和相關連接管道，編寫了數據採集程序實現數據實時顯示，並記錄整個運行中床體各點壓力、各處送風量。Based on the furnace chamber flame monitoring system, this paper designed and analyzed a combustion control system with the main steam pressure as the primary adjusting parameter and the total radiant energy of the furnace chamber as the subsidiary parameter, and compared the advantages of the system with emulation research and the experimental test
在爐膛火焰監測系統的基礎上，設計分析了以主蒸汽壓力為主調、以爐膛總輻射能為副調參數的燃燒控制系統，並通過模擬研究和試驗驗證，比較了該方法的優越性。分享友人