膜層應力 的英文怎麼說

中文拼音 [mócéngyīnglì]
膜層應力 英文
stress in thin film
  • 膜 : 名詞1. [生物學] （像薄皮的組織） membrane 2. （像膜的薄皮） film; thin coating
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  1. The strain effect on physical properties of bilayer manganite thin films

    雙層錳氧化物薄膜中的應力效應
  2. The dissertation firstly discusses the reflectance of euv and soft x - ray in " multilayer system based on classical electrodynamics and optical characteristics of materials. the nns surface roughness in different spatial frequency range is carefully studied since scattering can seriously reduce the reflectance in euv and soft x - ray wavelength region. we discuss representative model of residual stress in

    首先從材料在極紫外、軟x射線波段的光學特性出發，討論了極紫外、軟x射線在理想和非理想多層膜系中的反射特性；研究了影響極紫外、軟x射線多層膜反射率的表面粗糙度的空間頻率范圍；重點探討了多層膜殘余應力的典型模型、應力形成機制以及薄膜的形成過程。
  3. Theoretical study of multilayer thermal stresses

    多層薄膜的熱應力研究
  4. The conclusion is that the extrusion presses between primary and secondary linings, elasticity of the waterproof layer and unblocked drainage layer are the vital factors influencing the waterproof layer of spraying - on acrylate membrane in tunnel composite linings

    試驗結果表明，襯砌間的擠壓應力、防水層的彈性恢復能力、通暢的排水層對丙烯酸鹽噴膜防水層在隧道復合式襯砌中的防水效能發揮重要作用。
  5. Secondly, been generalized the failure data of electrical connectors from working and testing environment, electric contact failure, insulation failure, mechanical connection failure and other failure are four mainly failure modes of connectors, moreover, built the faulty - tree to analyze their reliability level. however, contact fault failure was the most prevalent mode of electrical connectors. under natural working and reserving conditions, the contact stress decreasing, fretting and surface film growing are mainly reasons to make electrical connector failure

    其次，通過對現場、試驗場電連接器的失效情況進行統計和分析，總結出電連接器的四種主要失效模式：電接觸失效、絕緣失效、機械連接失效和其他失效，並對電連接器進行了故障樹分析，指出電接觸失效是電連接器失效的主要形式，而在正常的工作條件下，造成電接觸失效，即決定電連接器工作壽命的主要原因是氧化膜層的生長、接觸對磨損以及磨損腐蝕物的堆積，而影響氧化膜層的生長、接觸對磨損以及磨損腐蝕物堆積的主要因素是環境振動和溫度應力，為電連接器進行失效機理分析奠定了基礎。
  6. Typical temperature is 800 - 1000 in cvd diamond process, while the high temperature limits its application in optical window and coating such as gaas, zns etc. low temperature can not only make diamond crystal nucleus finer, reduce surface roughness of diamond films and lessen light dispersion, but also eliminate thermal stress

    化學氣相沉積金剛石膜過程中，襯底的典型溫度為800 1000 ，這么高的溫度限制了其作為gaas 、 zns等低熔點光學材料窗口和塗層的應用。低溫沉積金剛石膜不僅可以使晶粒細化，降低表面粗糙度，減小光的散射作用，而且可以消除熱應力。
  7. It can be concluded that the performance differences between the plate membrane and the hollow fiber membrane can be attribute to difference of the stresses in the membranes when they were under pressure and the difference of the strain caused in the membrane, besides the possible reason that the surface curvature difference between a plate substrate and a hollow fiber one may cause structure difference in the dense functional layer when coating. the stresses in a hollow fiber composite membrane under an outside pressure are quite different from that in a plate one in that they exert on the hollow fiber in both the radial and circular directions, and the compress strain of the hollow fiber is thus much more complex, which may cause the top layer crinkle and a decreased salt rejection

    分析認為造成平板復合膜（ ）和中空纖維復合膜（ ）性能差異的主要原因，除了平板基膜與中空纖維基膜因表面曲率不同可能引起在塗覆時形成的緻密功能層結構上的差異之外，由於中空纖維膜受外壓時，膜內部承受的應力形式與平板膜不同，會同時在徑向（膜厚度方向）和環向（膜面內方向）兩個方向產生壓應力，因此，所發生的形變也較為復雜，可能造成表面復合層的起皺或脫落，引起脫鹽率下降。
  8. The chemical composition, micro - structure and optical properties and its application of tio2 thin films deposited on k9 glass by using reactive electron - beam evaporation ( reb ) are studied through sem, tem, xps, xrd, spectroscopic ellipsometry ( se ) and uv - vis spectrophotometer in the dissertation, and the progresses of nucleation and growth of thin film are discussed from the point of view of dynamics and thermodynamics so that a structure model of tio _ ( 2 ) thin film is brought forward

    本文採用sem 、 tem 、 xps 、 xrd 、橢圓偏振儀（ se ） 、 uv - vis分光光度計等分析手段系統地研究了電子束反應蒸發方法在k9玻璃上制備tio _ 2薄膜的成分、結構和光學性能以及tio _ 2薄膜在光學多層膜中應用，並開發了膜系設計軟體。文中還從動力學和熱力學角度分析了tio _ 2超薄膜的形核生長過程，得出了tio _ 2薄膜的組織結構模型。
  9. Then, combined with the mechanism of vacuum preloading and based on the layer method, settlement calculation of vacuum preloading was analyzed. the study shows that the vacuum degree under membrane equivalent load method does not accord with the mechanism of vacuum preloading. based on the layer method, vacuum degree difference method and effective stress method are presented. the results show that the final settlement calculated by the vacuum degree difference method is more close to the observation results

    然後，結合真空預壓的機理，基於分層總和法的思想，對真空預壓沉降計算方法進行研究：指出用現有的膜下真空度等效荷載法進行沉降計算不符合真空預壓機理；提出了符合真空預壓機理的真空度差值法與有效應力法，前者所推算的最終沉降量較接近實測推算結果，後者與實際結果存在一定差距。
  10. This article analyses the reinforcement mechanism of pile - net composite foundation mainly, combining natural equilibrium arch theory and reinforced cushion tension membrane theory to deduce the calculation formula of the stress ratio of pile - soil in the pile - net composite foundation under embankment

    本文主要對樁網復合地基的加固機理進行分析，並結合自然平衡拱理論和加筋墊層拉膜效應理論推導出路堤下樁網復合地基樁土應力比計算公式，同時分析了各設計參數變化對樁土應力比的變化規律。
  11. Abstract : in the paper, the operation technology of electron beam evaporation plating aluminium - chromium alloy coating is studied the optimum technology is obtained by discussing the influence of votage, current on auter appearance, adhesion inner stress. the ingredients of coation and evaporation materials are analyzed, the results show that the chromium contents of coating are very different from that of evaporation materials, in the end, the corrosion - resistance of the coating consisting of different chromium contents is investigated

    文摘:本文研究了電子束蒸發鍍鋁-鉻合金塗層的制備工藝，通過討論不同的電壓、束流對膜層外觀、結合力、內應力的影響，確定了合適的陳鍍工藝，對塗層和膜料的成分進行了分析，表明塗層中鉻含量與膜料中鉻含量有較大差異，最後探討了不同含鉻量的塗層的耐蝕性。
  12. The main contributions of this work are included as follows : ( 1 ) numerical tests of the outside axial and helical flows were carried out respectively. the velocities and pressure profiles and shear distributions have been obtained and they were compared due to the different flow field. it is concluded that when no particles are deposited, the helical flow would lower the pressure on membrane surface to some little extent but not markedly

    （ 1 ）對外軸向流和外切向流兩種方式下膜器環隙內流場進行變參數數值實驗，作出流場及切應力的分佈規律，分析無顆粒沉積時層流條件下流動結構對過濾通量的影響，認為：採用外旋流的方式將對膜面壓力有削弱作用，但並不明顯。
  13. The article analyses negative effects of pretensioning for underground structure on waterproof coated membrane and introduces the way of treatment and quality control measures taken

    分析了地下工程結構預應力張拉對塗膜防水層的負面影響，介紹了採取的有針對性的處理方法以及保證防水施工質量的控制措施。
  14. By varying mo - to - si ratio ( ), stress in multilayers - can be compensated to a certian extent / and 13mpa low - stress mo / si multilayers is fabricated. this research is supported by the national natural science foundation of china and " 863 " project of china and innovation foundation of china academy of sciences

    實驗發現，通過改變多層膜兩種材料的比率、改變ar氣工作氣壓等方法，可以在一定程度上補償因貫穿擴散產生的壓應力，而採用同時改變比率和ar氣工作氣壓可以控制多層膜中殘余應力。
  15. The reason why the existence of cr underlayers enhanced the pma energy of tbco films is that the existence of cr underlayers leads to forming the columnar structure and enhancing the inner stress in tbco films, thereby, enhancing the pma energy

    金屬cr底層增強tbco薄膜垂直磁各向異性的主要原因是：金屬cr底層的存在將可以使得tbco非晶垂直磁化膜內產生柱狀結構，而且會增強薄膜的內應力，從而使得其磁各向異性能增加。
  16. Abstract : a laser damage facilities, which has mm size spot and operates in tem00 mode ， were achieved. in order to know the reasons of laser damage, the laser energy density was controlled near the damage threshold of the oxide thin films. according to the examined near - threshold damage morphology, the damage mechanisms of the optical coatings can be divided into two types. one was caused by melting of the coating materials, another by exploding, induced with the inner stress of the film. the plasma generated was an important reason to expand the damage area

    文摘:採用毫米量級大光斑的近單模的激光器，控制入射薄膜表面的激光能量，獲得了幾種常見單層膜和增透膜的損傷形貌，實驗結果表明，薄膜的損傷可區分為熔化型和應力型兩種，薄膜表面等離子體對損傷斑點的擴大有重要作用。
  17. Stress generating mechanisms was discussed. the residual stress of 40 - bilayer mo / si multilayers in a high reflectivity multilayer was - 500 mpa ( compressive ), stress generating cause may be attributed to interfacial diffusion

    重點研究了多層膜的殘余應力控制技術；通過對單層膜以及多層膜的應力狀態分析，得出應力主要是由膜層之間的貫穿擴散引起的。
  18. It is also found that the concentrations of reactant, catalyst, the time and temperature of action and the working conditions have perceptible effects on its membrane performances. in this paper, the application of these membranes is also introduced

    探討了原料濃度、交聯劑種類和濃度、催化劑、添加劑、反應時間和反應溫度對膜性能的影響，初步計算了聚乙烯醇/ 5102一a12o3復合納濾膜各膜層的阻力。
  19. At present, the more wide ways are spray and brush and so on, but these ones have many disadvantages, for example polluting environment, poor adhesion etc. magnetron sputtering is a green one and the adhesion of the film with the substrate is very good

    目前應用較廣泛的方法是噴塗和刷塗法等，這些方法普遍存在污染環境、附著力差等缺點;磁控濺射方法能夠實現綠色環保生產，而且膜層的附著力較好。
  20. After annealing, the refractive index of the film decreases. and, the annealing process release the stress of the films, which give the film a higher density

    退火使薄膜的折射率將低，釋放膜層中的應力，膜層結構更加緻密。
分享友人
分享到 Line

分享到臉書