膠體研磨器 的英文怎麼說
中文拼音 [jiāotǐyánmóqì]
膠體研磨器
英文
colloid mill- 膠 : Ⅰ名詞1 （某些具有黏性的物質） glue; gum 2 （橡膠） rubber 3 （姓氏） a surname Ⅱ動詞（用膠粘） st...
- 體 : 體構詞成分。
- 研 : 研同 「硯」
- 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
- 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
- 研磨 : 1. （用工具研成粉末） grind; pestle2. （用磨料摩擦器物使變得光潔） abrade; polish
-
An excellent adhesive was prepared from bismaleimide ( bmi ), epoxy resin ( e - 51 and tde - 85 ), 4, 4 ' - diaminodiphenyl sulfone ( dds ) in this thesis. the influence of liquid rubber and polymer ether imide ( pei ) on the properties ( especially high - temperature strength and the peeling strength ) were discussed, their different toughening characteristics and mechanisms were discussed. last, the process and effection of heat - resisted structural adhesive were studied by adhesive experiment of synchronizer in automobile. the results of investigation made clear : the adhesive, has good properties, especially heat - resisted properity
根據材料分子設計的原理，研究了二苯甲烷雙馬來酰亞胺（ bmi ） 4 ， 4 』 ?二胺基二苯基碸（ dds ） e ? 51 tde ? 85組成的環氧膠粘劑體系，研究該體系在作為高溫結構膠粘劑使用時的粘接性能；然後研究了用無規羧基液體丁腈橡膠（ ctbn ? x ）和聚醚酰亞胺（ pei ）分別來增韌該體系的增韌效果；最後通過碳纖維耐磨材料與同步器圓錐環的粘接實驗，研究了耐高溫結構膠粘劑的粘接工藝和使用效果。In this paper, the microstructure changes of polypropylene induced by a complex combination of shearing, compression, stretching and friction actions during single pan - milling or co - milling with iron, uhmwpe and waste tire rubber chips ( wtr ) were studied and the stress induced effects were revealed. the structure and morphological development of iron particulates and wtr during pan - milling and co - milling with polypropylene were also characterized. the properties of pp / fe, pp / wtr and pp / wtr / fe composites prepared through pan - milling techniques were investigated
本文利用磨盤型力化學反應器對被碾磨材料施加強大的剪切、環向應力、擠壓、拉伸和摩擦作用，研究聚丙烯碾磨和共碾磨粉碎過程微觀形態結構和性能的變化，以及聚合物在碾磨過程中呈現的力化學現象，並將其應用拓展至金屬、橡膠等體系，研究碾磨粉碎在聚丙烯鐵超微粉體的制備、高交聯密度彈性材料廢舊輪胎橡膠（ wtr ）的超微粉碎，以及pp fe ， pp wtr材料的性能與碾磨作用的關系。When change the component of adhesive its shear strength increased from 39. 3 mpa to 53. 5 mpa at room temperature and it have long - term usage at 180 with 25 mpa and can be served at 230 in short period. the addition of liquid rubber resulted in a 300 % increase in the peeling strength. the addition of polymer ether imide led to a 260 % increase in the peeling strength, a 15 % increase in shear strength and a 10 increase in tg ( tg = 195. 54 )
研究結果表明： bmi dds e ? 51 tde ? 85組成的膠粘劑體系的室溫剪切強度為39 . 3mpa ，當改變環氧樹脂的含量時，剪切強度提高到53 . 5mpa ；用無規羧基液體丁腈橡膠改性環氧樹脂膠粘劑時室溫剝離強度提高3 . 0倍；用聚醚酰亞胺改性環氧樹脂膠粘劑，室溫剪切強度最高可達45 . 2mpa ，剝離強度提高2 . 6倍，玻璃化轉變溫度tg = 195 . 54 ，比未增韌體系提高10以上；碳纖維耐磨材料與同步器圓錐環的粘接實驗結果表明，膠粘劑的使用工藝性能良好，滿足室溫剪切強度30mpa和180剪切強度12 . 5mpa的技術要求。
分享友人